SpiderCloud® Radio Node - SCRN-310 Hardware Installation Guide ® Part number: DOC-SCRN-310-HW-01, Rev. 0.
FCC Statements Caution: Any changes or modification cautions to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Table of Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radio Node Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 SpiderCloud Wireless, Inc.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide About this Manual This guide provides the system specifications of the SpiderCloud® Radio Node 310 (SCRN-310). It includes detailed hardware installation instructions, the boot sequence, and expected LED behavior both during the boot-up and under operating conditions. An appendix shows the radio node antenna patterns. The primary audience for this guide includes network planners, system administrators and installation personnel.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Radio Node Features The radio node supports the following features: • Complete enterprise mobility using licensed 3G and LTE spectrum • Self Organizing Network (SON) capabilities for autonomous setup, operation, and management • Secure boot • Transparent integration into enterprise network environments • Certificate-based authentication with the SpiderCloud services node Radio Node System Isometric Top View and Bottom View The radio no
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide System Specifications Following are the system specifications for the radio node frequency bands of operation, system size, environmental requirements, power, and compliance. Frequency Bands of Operation SpiderCloud Wireless currently provides two versions of the SCRN-310 for operation in the following UMTS and LTE band combinations.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Power The radio node is compliant with IEEE 802.3at (PoE+): • Power consumption: 23W maximum • UMTS transmitter output power: 1x 250 mW (24 dBm) RMS radio power • LTE transmit output power: 2x125 mW (24 dBm) Compliance • ETSI: — EN 301 489-1 — EN 301 489-23 — EN 301 908-1 — EN 301 908-3 — EN 50385 — EN 60950-1 (safety) • IEEE 802.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Antennas The radio node includes four integrated antennas: two UMTS antennas and two LTE antennas. The UMTS radio operates in 1x2 mode with receive diversity. The LTE radio operates in 2x2 mode with MIMO. Tip: To maximize antenna transmission, SpiderCloud Wireless recommends not installing the radio node inside a metallic enclosure.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Input Power The radio node receives its power from a standard PoE+ switch (typical) or injector. The radio node is fully compliant with the IEEE 802.3at Power Over Ethernet (PoE+) specification. Per IEEE 802.3at, use standard Cat 5e or better twisted-pair cable with a maximum length restriction of 100 meters (328 feet) for PoE+. This restriction minimizes power loss between the PoE+ power source and the radio node.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Step 3 Connect an Ethernet cable from the injector’s OUT port to the radio node. The injector will now inject power onto a pair of wire pairs in the cable. The radio node will expect a nominal 48V DC input (57V max) from a typical PoE+ injector. Select the Radio Node Location Radio nodes can be installed in a wide range of locations including walls, ceilings, and plenum spaces.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Use Table 2 to determine the maximum distance between radio node units. Greater separation may affect coverage or system performance. Table 2: Recommended Radio Node Separation Distances Type of Building Max Recommended Separation Warehouses and large open-spaced buildings 70 m (230 feet) Open-plan offices 45 m (148 feet) Closed-plan offices (e.g., individual rooms - plasterboard) 30 m (98 feet) Closed-plan offices (e.g.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Bracket Mounting and Cabling Guidelines Incorrectly cabling and mounting a radio node can result in crushed cables and loss of communications to the unit. Follow these guidelines in cabling the radio node and mounting it on the bracket: • Ensure that the cabling is properly routed and dressed. • Ensure that the pedestal base is fully inserted into the mount bracket so that it locks into place and is flush.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Transmit Side Figure 10 Attach the Mount Bracket Step 2 Insert the RJ-45 connector into the Ethernet port as shown in Figure 13.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Figure 12 Fully Mounted Installing the Radio Node (Method 2) To route the cable directly and mount the radio node Step 1 Route the Ethernet cable through the large hole in the mounting bracket. Transmit Side Figure 13 Mount Bracket with Direct Cable Routing Step 2 With two user-provided screws, attach the mount bracket assembly to a wall or ceiling. The screw holes are sized for an M4 (#10) screw.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide RJ-45 Connector in Ethernet Port Figure 14 Route and Terminate the Cable Step 4 Push as much cable back through the wall or ceiling as possible. The mount bracket assembly has room for some cable slack. Step 5 Slide the pedestal base of the radio node into the groove opening in the mount bracket. When the pedestal reaches the end of the trough, a spring clip will secure the unit into place.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Completing the Installation Step 1 Attach a padlock or cable tie wrap through the cutout lock holes in the mount bracket and pedestal base. Figure 16 Padlock and Lock Holes The lock in the above figure is shown schematically. The orientation is for illustration purposes (not accurate) since the bracket is typically wall or ceiling mounted. Step 2 The radio node boots up and attempts to connect to the services node.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Boot Sequence and Services Node Communication On initial boot, the radio node performs the following boot sequence and communicates with the services node. It performs this boot sequence twice, first for the UMTS subsystem, then again for the LTE subsystem. This sequence takes about one minute to complete for each subsystem. When finished, all devices are reachable.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Radio Node LED Boot Sequence The radio node state machine is sequential and progresses in the following order: State 0 -> State 1 -> State 2 -> State 3 -> State 4 -> State 5 A normal boot sequence transitions through all these states sequentially and the LED state transitions accordingly. If the radio node fails to transition to the next state, the system restarts the boot sequence, starting with State 0.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Table 3: Radio Node LED Boot Sequence (continued) State 3. TFTP LED Color Flashing Blue Description Possible Failures and Actions The radio node proceeds next to download the operating system image from the services node. The radio node moves to the next state (State 4) after the image has been downloaded. 4. Operating System Booting Flashing Green The radio node loads the operating system and starts the default platform applications.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Table 4: Radio Node LED Behavior (continued) LED Status Blue: fast flashing Locate radio node enabled* Blue: solid Follow IMSI enabled* Off Powered off or LED disabled Flash Rate Approximately 1 second on/off cycle * Refer to the SpiderCloud OS (SCOS) Administrator Guide for information about the locate radio node and follow IMSI features.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide The SpiderCloud Documentation Set The SpiderCloud documentation set includes: • The SpiderCloud System Description provides an overview of how the SpiderCloud system fits within an operator’s network and in an enterprise, describes key features of the system, and provides specifications for the services and radio nodes.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Appendix A: UMTS Antenna Patterns 0º UMTS Band Antenna Patterns 90º Up Front 0o 3 dB -30o 30o 0 -3 -6 -60o 60o -9 -12 -15 90º -90o 9 0o -15 0º -12 -9 -6 -120o Front 120o 90o 3 dB 120o -3 0 -150o 60o 0 -3 150o 3 dB -6 150o 180o AUT = 2140 MHz : Max Gain = 2.59 dBi at 90 o 1 30o -9 1 AUT = 2140 MHz : Max Gain = -0.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide PCS Band Antenna Patterns 0º 90º Up 0o Front 3 dB -30o 30o 0 -3 -6 -60o 60o -9 -12 -15 -90o 9 0o 90º -15 -12 0º -9 -6 -120o 120o -3 90o Front 3 dB 120o 0 -150o 60o 0 -3 150o 3 dB -6 150o 180o AUT = 1960 MHz : Max Gain = 4.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide DCS Band Antenna Patterns 0º 90º Up Front 0o 3 dB -30o 30o 0 -3 -6 -60o 60o -9 -12 90º -15 -90o 9 0o 0º -15 -12 -9 90o Front -6 -120o 3 dB 120o 120o -3 0 -150o 60o 0 -3 150o 3 dB -6 150o 30o -9 180o -12 AUT = 1844 MHz : Max Gain = 3.55 dBi at 54 o 1 1 -15 AUT = 1844 MHz : Max Gain = 0.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide 26 SpiderCloud Wireless, Inc.
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Appendix B: LTE Antenna Patterns LTE Band 4 Antenna Patterns 0º Up 90º Front 0o 3 dB -30 o 30 o 0 -3 -60 o 60 o -6 -9 90º -12 90 o Top -90 o -12 0º -9 -6 -120 o Front 120 o -3 90o 0 o -150 o 3 dB 3 dB 120 150 o 60o 0 180 o -3 150o EL1 Cut (Front-to-Back) 30o -6 -9 -12 180o 0o -12 0º -9 -6 Up -150o 90º -30o -3 0 0o -30 o 3 dB -120o 30 o 3 dB -60o -90o 0 AZ Cut -3 -60 o 60 o -6 -9 -12 -90 o
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide LTE Band 7 Antenna Patterns 0º Up 90º 0o Front -30 o 3 dB 30 o 0 -3 -60 o 60 o -6 -9 -12 90º -90 o 90 o Top -12 -9 0º -6 -120 o 120 o -3 Front 90 0 -150 o 3 dB 3 dB 120 o 150 o 60 o 0 180 o -3 150 o EL1 Cut (Front-to-Back) 30 o -6 -9 -12 180 o 0o -12 -9 0º -6 -150 o Up 90º 0 -120 o 0o -30 o -30 o -3 3 dB -60 o 3 dB -90 o 30 o AZ Cut 0 -3 -60 o 60 o -6 -9 -12 -90 o 90 o -12 -9 -6 -120 o