Product Specs

ManualsBrandsSpektrum ManualsElectronicsSLT2 2CH TX

Table Of Contents

SLT2 2CH 2.4GHz Transmitter manual

Product specification

• Model number:SPMSLT200F(SLT2 2CH TX);

• PMN:SPMSLT200

• Power supply:4.0V~6.6V;

• Working frequency:2.4G;

• Transmitted power:<40mW;

• Control distance:>100meters;

• Battery:4*AA;

• Adjust method: Knob adjust & Switch adjust.

• Operating temperature:-10~55℃

Main function

• 2CH transmitter, It can adjust steering(CH1/ST) TRIM、DR、REV、

EPA. Can adjust throttle(CH2/TH) DR、EPA.

• Low battery voltage alarm.

Warning

Please strictly follow the supply voltage mentioned in the manual. Excessive

supply voltage may cause the equipment to burn.

Transmitter battery is suitable for 4 alkaline batteries, ensure that the

positive and negative batteries are installed correct, incorrect battery polarity

will cause damage to the transmitter! The transmitter uses red LED to indicate

the battery power. When the red LED blinks from steady on to slow, it means

the battery power is low. Please replace the battery in time!

Transmitter

Summary of content (6 pages)

PAGE 1
SLT2 2CH 2.4GHz Transmitter manual Product specification • • • • • • • • Model number:SPMSLT200F(SLT2 2CH TX); PMN:SPMSLT200 Power supply:4.0V~6.6V; Working frequency:2.4G; Transmitted power:<40mW; Control distance:>100meters; Battery:4*AA; Adjust method: Knob adjust & Switch adjust. • Operating temperature:-10~55℃ Main function • 2CH transmitter, It can adjust steering(CH1/ST) TRIM、DR、REV、 EPA. Can adjust throttle(CH2/TH) DR、EPA. • Low battery voltage alarm.
PAGE 2
Install battery Transmitter battery is suitable for 4pcs 1.5V AA alkaline batteries, Install the battery according to the mark in the battery box. 1. Press the battery cover hook in the direction of the arrow, and open the battery cover downward; 2. According to the mark in the battery box, put four AA batteries in turn. Do not put the wrong polarity, and do not mix old and new batteries. Do not mix batteries of different specifications. 3. Close the battery cover upward and close the hook.
PAGE 3
TH Transmitter can control throttle (TH/CH2). You can pull throttle trigger to backward to control car forward or push throttle trigger to forward to control car backward. ST DR(SR) Transmitter can adjust steering (ST/CH1) travel. You can rotate clockwise ST DR rotary knob to add steering (ST/CH1) to MAX travel, also you can rotate anticlockwise ST DR rotary knob to reduce steering (ST/CH1) to Min travel, range is 20%-100%. TH FORWARD D/R(TH/LIM) Transmitter can adjust throttle forward (TH/CH2+) travel.
PAGE 4
The setting is as follow: . Step1.turn steering wheel to max right position and push throttle trigger to max forward position, Hold them and push power button to open transmitter. . Step2.transmitter red LED will flash rapidly, It means transmitter enter EPA setting state, release steering wheel and throttle trigger to nature position (middle position). . Step3.turn steering wheel to max left position and holding, rotate SR rotary knob clockwise/anticlockwise to add/reduce steering left endpoint. . Step4.
PAGE 5
Note: Before the transmitter leaves the factory, the throttle and steering neutral point and the max travel have been calibrated OK. Incorrect throttle calibration will cause the motor to be unable to output the full throttle travel or the throttle backward is not linear; Incorrect steering calibration may result in the steering servo not being able to output at full Angle or not being linear at the back of the steering. At this point you need to do a calibration of the throttle and steering.
PAGE 6
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.