User's Manual

ManualsBrandsSpeed Dragon Multimedia ManualsElectronicsSATA-IDE Bi-directional Adapter

Table Of Contents

SE-MANL-BSA2-S1-1IDE-1

User’s Manual

INTRODUCTION

This SATA - IDE Bi-directional adapter is designed for use on any motherboard with one available Serial ATA

(SATA) host port or one available IDE port. With this product, end-user can easily add a SATA device to the

motherboard’s IDE port, or add an IDE device to motherboard’s SATA port. This product complies with

Ultra ATA 133 and SATA 1.0a specificaions and offers superior performance and unmatched data transfer

rates.

FEATURES & SPECIFICATION

General

z Unique bi-directional SATA ÅÆ IDE converter

z Supports 3.5” SATA and IDE (ATA) hard drives

z Supports 5.25” SATA and IDE (ATA) optical drives

z Power-On and HDD-Activity LED indicators

z Ultra low power consumption

z Connectors: one IDE (ATA) connector, one SATA host connector (Yellow), one SATA device

connector (Black) and one 4-pin FDD power connector

z Driverless. No driver is needed

Serial ATA Interface

z Complies with SATA 1.0a specification

z Supports SATA Generation1 transfer rate of 1.5Gbps (150MB/s)

z Supports Spread Spectrum in receiver

z Supports SATA power saving mode: Partial and Slumber

IDE (ATA) Interface

z Complies with ATA specification

z Complies with UltraATA 133 with transfer rate up to 133MB/s

z Supports PIO mode 0, 1, 2, 3, 4, 5, 6, MDMA mode 0, 1, 2 and UltraDMA mode 0, 1, 2, 3, 4, 5, 6

z Supports Master/Slave/Cable Select mode by configuration switches

Package Contents:

z SATA - IDE Bi-directional adapter x 1

z SATA cable x 1

z Small and big 4-pin power extension Y-cable x 1

Summary of content (4 pages)

PAGE 1
SE-MANL-BSA2-S1-1IDE-1 User’s Manual INTRODUCTION This SATA - IDE Bi-directional adapter is designed for use on any motherboard with one available Serial ATA (SATA) host port or one available IDE port. With this product, end-user can easily add a SATA device to the motherboard’s IDE port, or add an IDE device to motherboard’s SATA port. This product complies with Ultra ATA 133 and SATA 1.0a specificaions and offers superior performance and unmatched data transfer rates.
PAGE 2
INSTALLATION Before installing this product, let us make the following assumptions: End users must have the basic knowledge of installing a device and its software driver to a computer. If they are not sure about their abilities or have any queries, please call their local dealers immediately, or find somebody who is experienced and qualified for assistance. Connecting an IDE Device to the motherboard’s SATA Port: 1. Turn off your computer and all devices connected to it. 2. Remove the computer’s cover.
PAGE 3
. Depending on the existing IDE devices (if any) on your system, follow the direction below to configure Master/Slave/Cable Select mode of this product (Figure 2). Figure 2: Master/Slave/Cable Select mode configuration 4. Insert this product into an IDE port on the motherboard (Figure 3). 5. Connect the Black SATA connector on the adapter to the SATA device using a SATA cable (Figure 3). Figure 3: SATA Device to motherboard’s IDE Port connection 6.
PAGE 4
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.