User's Manual

ManualsBrandsSpectrum Tracking Systems ManualsElectronicsTransceiver for wireless data transmission

SM-ETS Confidentia Spectrum Tracking Systems, LLC 2545

Tarpley Road

Carrollton, Texas 75006

SM-ETS, lms, 2013-07-10Page1of4

TPC2 Operating Instructions

Warning RF Exposure Compliance

The antenna(s) used for this transmitter must be installed to provide a separation

distance of at least 20 cm (7-7/8 inches) from all persons and must not be co-located or

operating in conjunction with any other antenna of transmitter.

Users and installers must be provided with antenna installation instructions and

transmitter operating conditions for satisfying RF exposure compliance.

This device may not interfere with TV reception or Federal Government radar.

User FCC Compliance

This transmitter is authorized by rule under the Low Power Radio Service (47 CFR

part 95) and must not cause harmful interference to TV reception or United States Navy

SPASUR installations. You do not need an FCC license to operate this transmitter. This

transmitter may only be used to provide: auditory assistance to persons with disabilities,

persons who require language translation, or persons in educational settings; health

care services to the ill; law enforcement tracking services under agreement with a law

enforcement agency; or automated maritime telecommunications system (AMTS)

network control communications. Two-way voice communications and all other types of

uses not mentioned above are expressly prohibited.

Device Preparation, Standard Firmware

1. Device preparation should be completed in a location where there is cellular

coverage; i.e., outside screen-room or anechoic chamber.

2. Remove the device from its ‘host enclosure’, and place device onto the Mag-Plate.

3. While maintaining device on Mag-Plate, connect the battery leads.

4. Observe the device. After a few seconds the on-board Green LED should

illuminate, indicating that the cellular module has powered up. The ‘installation’

message sequence requires approximately one minute for completion. The device

has returned to its Dormant-Standby state after the Green LED extinguishes. The

‘installation’ message sequence includes: CDMA/PCS network registration, DNS

look-up, location-fix receipt, and bi-directional UDP data communication with the

WebTracker Server. The VHF transmitter remains OFF.

Summary of content (4 pages)

PAGE 1
SM-ETS Confidentia Spectrum Tracking Systems, LLC Tarpley Road Carrollton, Texas 75006 2545 TPC2 Operating Instructions Warning RF Exposure Compliance The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm (7-7/8 inches) from all persons and must not be co-located or operating in conjunction with any other antenna of transmitter.
PAGE 2
SM-ETS Confidentia Spectrum Tracking Systems, LLC Tarpley Road Carrollton, Texas 75006 2545 5. Insert the device into its ‘host enclosure’ while maintaining device in close proximity to the Mag-Plate. This isn’t critical, but it minimizes the possibility of inadvertent activation. Device Operation, Standard Firmware 1. It is assumed that the device is on the Mag-Plate and is in Dormant-Standby state. Separate the device from the Mag-Plate by at least 6 inches.
PAGE 3
SM-ETS Confidentia Spectrum Tracking Systems, LLC Tarpley Road Carrollton, Texas 75006 2545 Device Repacking, Standard Firmware 1. While maintaining the device in proximity with the Mag-Plate, remove it from its ‘host enclosure’. This isn’t critical, but it minimizes the possibility of inadvertent activation. 2. While maintaining the device in proximity with the Mag-Plate, disconnect the battery leads. Device Preparation, VHF Test Firmware 1.
PAGE 4
SM-ETS Confidentia Spectrum Tracking Systems, LLC Tarpley Road Carrollton, Texas 75006 2545 Device Operation, VHF Test Firmware 1. It is assumed that the device is on the Mag-Plate and is in Dormant-Standby state. Separate the device from the Mag-Plate by at least 6 inches. The device will activate immediately (no integration). Upon activation, the VHF transmitter starts and continuously outputs signal.