49531 / 01 User Guide • guÍa del usuario • guide d’utilisation www.kwikset.
Contents 4 Kevo Overview 5 System Requirements for Smart Devices 6 Getting Started 6 Install the Kevo Lock Download the Kevo Mobile App Programming Instructions 6 6 7 Smart Devices 7 eKeys 8 Fobs 9 Resetting Your Kevo System Normal Operation 11 12 Unlocking the Door 12 Locking the Door 13 Error Notifications 14 Audio/Visual Feedback 16 Battery Replacement 18 Fob 18 Deadbolt 19 Troubleshooting 20 System Updates 20 Regulatory Compliance 21 FCC 21 Industry Canada 21 Tec
Kevo at a Glance Exterior Deadbolt rose (touch surface) Light ring SmartKey tool hole Keyway Interior (cover removed) Reset button Calibrate button Back panel Program button Switches Status LED Turnpiece Switches ON OFF Turn On/Off Beeping Sound (ON by default) Turn On/Off Status LED (ON by default) Triple Touch Lock (OFF by default) See page 14.
Kevo Overview You may choose to use only Kevo fobs, only smart devices, or a mix of both in your Kevo system. In order for your smart device to connect to the lock, you will need to download the Kevo mobile app. The app acts as your virtual key and runs in the background without you even having to remove it from your pocket or purse to unlock the door. You can grant family and friends access to your Kevo lock by giving them Kevo fobs or sending eKeys to their smart devices.
System Requirements for Smart Devices A Kevo compatible smart device must have Bluetooth Smart Ready/ Bluetooth 4.0, and the Kevo app specific to the device must be installed. Find out if your device is compatible by consulting our website: www.kwikset.com/kevo/devices If your device is compatible, the QR code above will transfer you directly to your device’s app store so you can download the Kevo app. If your device is not compatible, you can still use the Kevo fob to operate your lock. See page 9.
Programming Instructions Smart Devices ENGLISH Note: Throughout this manual, smart devices (phones, tablets and mobile internet-connected devices) will be referred to as “smartphones” or “phones.” All smartphones will be configured through the Kevo app. The first phone you setup with the lock will become the Owner of the lock. You can send eKeys to friends and family with compatible smartphones and use the app to decide who receives Admin rights in your system.
Disabling Your Lost or Stolen Smartphone If your phone is lost or stolen, use the Kevo web portal to delete or disable your old phone: www.kwiksetkevo.com Transferring Your Information to a New Phone When you get a new phone, download the Kevo app and sign in. All of your settings will be transferred to your new phone and deleted from your former phone.
Fobs The Kevo fob that came with your Kevo lock is already enrolled in the lock, but it is recommended that you perform the calibration process below. Note: In order to have a mix of smartphones and fobs in your Kevo system, a Kevo compatible smartphone must be designated as the Owner of the lock. See page 7. Kevo Fob Calibration The calibration process will help the Kevo lock learn where you normally carry your fob while locking and unlocking the door.
The following sections show you how to enroll and remove Kevo fobs in a fob-only system or in a fob-and-phone system. Note: A single fob can be enrolled in multiple Kevo locks. Note: The fob that came with your Kevo lock is already enrolled in the lock. Fob-Only System enrolling an additional fob 1. Push the Program button on the back panel. 2. Hold an already enrolled fob close against the back panel until you hear one beep. 3. Use a ballpoint pen to press the enroll button on the new Kevo fob.
removing a fob Note: If you lose a fob from a fob-only system, you will need to reset the lock to delete the fob from memory. enrolling the first fob after a factory reset 1. Push the Program button on the back panel. 2. Press the enroll button on the fob. 3. Hold the fob close against the back panel. Once the Kevo lock beeps twice and the fob’s LED turns solid green, the fob has enrolled successfully. You may now perform the Kevo fob calibration process on page 9.
Normal Operation Unlocking the Door From the Outside To unlock the Kevo lock (while your smartphone or fob is in your pocket or purse), hold one finger against the deadbolt rose until the light ring spins blue. The light ring will flash green twice and you will hear two beeps. The door will unlock. Tip: The deadbolt rose is the entire metallic guard extending from the light ring to the door. You can touch the rose in any location.
Locking the Door From the Outside To lock the door (while your smartphone or fob is in your pocket or purse), hold one finger against the deadbolt rose until the light ring spins blue. The light ring will flash amber and you will hear one beep. The door will lock. If someone with a Kevo device that is not authorized in your system touches the rose, the light ring will spin blue, then flash red. The door will not lock. If someone without a Kevo device touches the rose, the light ring will just spin blue.
