Sent build INC Set-08-9% 11:36am from 65056730665585 1189 Fade To Our Valued Customer Congratulations and thank you for purchasing a TITAN Technologies Access Locket. Your Access One Locket fs an exciting new product that gofers the ultimate in convenience and security by integrating conventional locket engineering with the most secure form of radian Adequacy technology available. There are several key featureless of your Accusing Locks es Hat we wil to highlight.
Sent build INC Set-08-9% 11:36am from 65056730665585 1189 Page 3 1.0 Door & Jamb Preparation / Latch Installation. 1.1 For new door preparation, begin by following drilling instructions on the template included. __ & Remove any existing hardware from road and jamb, 1.3 Determine backseat of door by measuring from edge of door to canter of large hole, 1.4 Adjust deadbolt tats (a) for a (70mm) backseat position if required, by rotating 1/2 tum. 1.5 Inge deadbolt arch through hole in adj of door. 1.
Sent build INC Set-08-9% 11:37am from 65056730665585 1189 rage 4 2.0 installation of Deadbolt Assembly 2.1 Open door to abase installation, 1 Place exterior deadbolt assembly (a) on exterior of road, aligning tailpiece (b) through deadbolt latch while passing the wire {c) under the deadbolt latch 10 the interior side of the door 2.3 On interior side of door, place mounting slate (d) so that wire is routed up through bridge {e) in plate. and caress of mounting piste is aligned with center of large hole.
Sent build INC Set-08-9% 11:37am from 65056730665585 1189 Ease ยง 3.0 Receiver Module Installation 8.1 Innermost handing of road by referring to diagram. . Units are prepackaged in right-handed (RH) configurations (unless pacified otherwise), f you determined your door to be right handed in step 3.1, skip to step 3.4. 3.3 Adjustment for left-handed doors; 1. Carefully remove the insert rack (a) using = small flat object (screwdriver, knife, catch. 2. Place the tumescence (b) in a straight vertical position.
Sent buwiD2M INC Set-08-9% 11:37am from 65056730665585 1189 Fade 4.0 Programming Transmitters. 4.1 Open door 50 {hat audio signals can be heard during programming. _Place the salver into PROGRAM MODE (P) by siding the MODE switch (a) (located in battery compartment) to the left most position. You will hear 2 audible beeps to confirm you have entered PROGRAM MODE. 4.3 Paint the {remote central) transmitter (b) toward the receiver module and push the LOG and UNLOCK buttes simultaneously.
Sent build INC Set-08-9% 11:38am from 65056730665585 1189 Fade 77 5.0 Operational Features 5.1 To remote LOCK the deadbolt, point transmitter towards door, push the LOCK icon on transmitter. The bolt will extend, 3 audio seeps will signal and the light on the exterior deadbolt housing will ash red for several seconds. 5.2 To remote UNLOCK the deadbolt, point transmitter towards door, push the UNLOCK icon an transmitter.
Sent build INC Set-08-9% 11:38am from 65056730665585 1189 6.0 Replacing Receiver Module Batteries 6.1 Remove battery cover {a} by pushing in at nectar of cover and sliding up and off. SLIDE OFF B.2 Inst ail {4} AA alkaline batteries {b) as indicated by the markings on receiver module. Unit will beep to indicate it is powered up. Note: For optimum pharmaceutic, do not use rechargeable batteries, 5.3 Snap cover back onto module.