User's Manual

HomeConnect Lock Configuration Guide
HomeConnect Lock Configuration Guide
HomeConnect Lock Configuration Guide
Home Connect
44571 / 04
English
1. Ensure you have followed all the steps in
the SmartCode Quick Installation Guide.
2. Locate and remove the interior cover from
your HomeConnect lock to expose the
Programming Instructions on the lock. See
Figure 1.
3. For inclusion or exclusion of the lock, refer
to your Z-Wave or ZigBee control system
instructions and reference Figure 2.
Notes
1. This HomeConnect lock supports 30 user
access codes. It is recommended to add
or change access code(s) directly from the
Z-Wave or ZigBee Control system.
2. Deleting access code(s) can only be
done directly from the Z-Wave or ZigBee
control system.
3. Depending on the controller location
and Z-Wave protocol version, it may be
necessary to perform the inclusion process
on the HomeConnect Lock within 12
inches from the control system. During
the inclusion process, ensure that both
the control system and HomeConnect lock
remain stationary for a total of 60 seconds
to complete the encryption exchange and
for the lock to be properly displayed on the
Z-Wave control system.
4. Z-Wave is a “Wireless mesh network,” and
although Z-Wave has an estimated open air
range of 65 feet, results may vary based on
building construction and communication
path, with 35 feet+ installed distance being
typical. It may be necessary to install a
repeatable or beaming Z-Wave device (i.e.
lamp module) to enhance the communication
path with the controller for a more robust
Z-Wave network.
5. If first inclusion attempt was unsuccessful,
perform exclusion process (see Figure 2) to reset
the lock. Then, repeat the inclusion process.
Español
1. Ensure you have followed all the steps in
the SmartCode Quick Installation Guide.
2. Locate and remove the interior cover from
your HomeConnect lock to expose the
Programming Instructions on the lock. See
Figure 1.
3. For inclusion or exclusion of the lock, refer
to your Z-Wave or ZigBee control system
instructions and reference Figure 2.
Notes
1. This HomeConnect lock supports 30 user
access codes. It is recommended to add
or change access code(s) directly from the
Z-Wave or ZigBee Control system.
2. Deleting access code(s) can only be done
directly from the Z-Wave or ZigBee control
system.
3. Depending on the controller location and
Z-Wave protocol version, it may be necessary
to perform the inclusion process on the
HomeConnect Lock within 12 inches from
the control system. During the inclusion
process, ensure that both the control system
and HomeConnect lock remain stationary
for a total of 60 seconds to complete the
encryption exchange and for the lock to be
properly displayed on the Z-Wave control
system.
4. Z-Wave is a “Wireless mesh network,” and
although Z-Wave has an estimated open air
range of 65 feet, results may vary based on
building construction and communication
path, with 35 feet+ installed distance being
typical. It may be necessary to install a
repeatable or beaming Z-Wave device (i.e.
lamp module) to enhance the communication
path with the controller for a more robust
Z-Wave network.
5. If first inclusion attempt was unsuccessful,
perform exclusion process (see Figure 2) to reset
the lock. Then, repeat the inclusion process.
Français
1. Ensure you have followed all the steps in
the SmartCode Quick Installation Guide.
2. Locate and remove the interior cover from
your HomeConnect lock to expose the
Programming Instructions on the lock. See
Figure 1.
3. For inclusion or exclusion of the lock, refer
to your Z-Wave or ZigBee control system
instructions and reference Figure 2.
Notes
1. This HomeConnect lock supports 30 user
access codes. It is recommended to add
or change access code(s) directly from the
Z-Wave or ZigBee Control system.
2. Deleting access code(s) can only be done
directly from the Z-Wave or ZigBee control
system.
3. Depending on the controller location and
Z-Wave protocol version, it may be necessary
to perform the inclusion process on the
HomeConnect Lock within 12 inches from
the control system. During the inclusion
process, ensure that both the control system
and HomeConnect lock remain stationary
for a total of 60 seconds to complete the
encryption exchange and for the lock to be
properly displayed on the Z-Wave control
system.
4. Z-Wave is a “Wireless mesh network,” and
although Z-Wave has an estimated open air
range of 65 feet, results may vary based on
building construction and communication
path, with 35 feet+ installed distance being
typical. It may be necessary to install a
repeatable or beaming Z-Wave device (i.e.
lamp module) to enhance the communication
path with the controller for a more robust
Z-Wave network.
5. If first inclusion attempt was unsuccessful,
perform exclusion process (see Figure 2) to reset
the lock. Then, repeat the inclusion process.
Copyright © 2013 Spectrum Brands, Inc.
For technical assistance,
call 1-866-863-6584
For technical assistance,
call 1-866-863-6584
For technical assistance,
call 1-866-863-6584
PROGRAM
BUTTON
SETTINGS
Press program button below once to enter
the 1st code & twice for the 2nd code
Enter code on exterior keypad
Press on exterior keypad to set code
PROGRAM MI NG
INSTRUCTIO NS
READY
Future Feature
Mute Beeper
Auto-Lock
LED Notification
A B
A (x1) A (x1)
A (x4) B (x9)
Inclusion
Inclusión
Inclusion
HomeConnect Lock Type
HomeConnect Lock Type
HomeConnect Lock Type
Z-Wave
Zigbee
Exclusion
Exclusión
Exclusion
Inclusion/Exclusion Configuration Process for HomeConnect Locks
Inclusion/Exclusion Conguration Process for HomeConnect Locks
Inclusion/Exclusion Conguration Process for HomeConnect Locks
Fig. 1 Fig. 2