User Manual

ManualsBrandsSpectralink ManualsElectronicsISM SYSTEM 600

KIRK System IP600-ISM - User’s Guide

1. Introduction

This guide will help you set up the KIRK System IP600-ISM on a Cisco CallManager. Please refer to

your CallManager user’s manual for general information.

2. Installation

1. Mount the KIRK System IP600-ISM on a wall, where coverage is needed, using the mounting

KIT.

2. Connect the system to the Call Manager LAN network using a standard patch cable.

3. Connect the system to a power supply using only power supplies from KIRK telecom.

4. Verify that the LED’s are flashing as follows:

Active

In HTTP mode and when packets are transmitted on the Ethernet the Active LED is

turned on. In TFTP mode it will be turned on when the Interface Card has detected an

Ethernet connection.

100

In HTTP mode and when the Ethernet speed is 100mbps the 100 LED is turned on.

When 10mbps Ethernet is connected it will be off. In TFTP mode the 100 LED will be

turned on when the Interface Card has detected an Ethernet connection.

Link

When the Ethernet link layer is established the Link LED is turned on.

Ready

When the system is running and ready the Ready LED is turned on. If the system is not ready the

LED will start flashing.

Front LED

The front LED is green when the system is running and the subscriptions are read.

Software and help files are available at: http://www.kirktelecom.com/company/suk181.asp

Summary of content (7 pages)

PAGE 1
KIRK System IP600-ISM - User’s Guide 1. Introduction This guide will help you set up the KIRK System IP600-ISM on a Cisco CallManager. Please refer to your CallManager user’s manual for general information. 2. Installation 1. Mount the KIRK System IP600-ISM on a wall, where coverage is needed, using the mounting KIT. 2. Connect the system to the Call Manager LAN network using a standard patch cable. 3. Connect the system to a power supply using only power supplies from KIRK telecom. 4.
PAGE 2
3. IP Addresses The KIRK System IP600-ISM is pre-configured with the IP address: 192.168.0.1. This address has to be changed for customizing the sub-net mask of the network. Start configuring a PC to the IP system’s identical net mask, e.g. the address: 192.168.0.2 and sub-net mask: 255.255.255.0. The system is now ready to be reached with a standard internet browser. To change the address in the card to e.g. 172.180.0.170 please follow the steps below: 1.
PAGE 3
5. Registration of Users on the CallManager Users must be registered on the CallManager as well as on the KIRK IP Interface Card. Please follow the steps below to register users on the CallManager: 1. Start the CallManager software 2. Select "Device” -> ”phone” 3. Select ”add a new phone” 4. In the field “phone type” select “Cisco 7940” and press next 5. Type i.e. the handset serial number (without space) in the field ”MAC address” 6. Type a description of the handset in the field ”description” 7.
PAGE 4
7. Subscription of Handsets Before registering handsets on the system, the system must be set to “subscription allowed”. The subscription setting can be changed in the info menu. 1. From the handset choose the SUBSCRIPTION CREATE menu to subscribe to the new system. Use the < and > keys to scroll between the IDs of the different systems if there are more than one system available. If the handset is already subscribed to 10 systems you will need to remove one of the existing subscriptions. 2.
PAGE 5
Appropriate RF safety/installation information The System IP600-ISM base is intended to be installed by authorized personal. The base station shall be installed in accordance with FCC rules. The System IP600-ISM shall be placed at a location in such way, that there is at least 20 centimetres between the base transmitter and the users body or any other nearby persons.
PAGE 6
Exposure to sunlight, heat and moisture Do not expose the cordless phone to direct sunlight for long periods. Keep the cordless phone away from excessive heat and moisture. Battery disposal Defective batteries must be returned to a collection point for chemical waste disposal. Spare parts and accessories Use only approved spare parts and accessories. The operation of non-approved parts cannot be guaranteed and may even cause damage.
PAGE 7
is warranted to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser’s receipt. Our obligation under this warranty is limited to repair or replacement (at our option) of the product or any part(s) which are defective provided that the product is returned to the original place of purchase or an authorized service location during the warranty period.