16-Channel Digital Video Recorder WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Operation Instruction Important Safeguards 1. Read Instructions All the safety and operating instructions should be read before the appliance is operated. 10. Overloading Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 2. Retain Instructions The safety and operating instructions should be retained for future reference. 11.
16-Channel Digital Video Recorder Table of Contents Chapter 1 — Introduction ........................................................................................................... 1 Feature ................................................................................................................................... 1 Technical Overview................................................................................................................ 1 Chapter 2 — Installation ........................
Operation Instruction Setup Screen ....................................................................................................................... 12 System Setup....................................................................................................................... 12 Information ....................................................................................................................... 12 Date/Time .........................................................................
16-Channel Digital Video Recorder Bookmarks ....................................................................................................................... 63 Clip-Copy ......................................................................................................................... 63 Appendix .................................................................................................................................. 65 USB Hard Disk Drive Preparation ..................................
Operation Instruction Figure 30 — Motion Detection Settings screen. .......................................................................................27 Figure 31 — Motion Detection Actions 1 screen. .....................................................................................28 Figure 32 — Motion Detection Actions 2 screen. .....................................................................................28 Figure 33 — Video Loss Settings screen. ...........................................
16-Channel Digital Video Recorder Chapter 1 — Introduction Feature Your color digital video recorder (DVR) provides recording capabilities for 16 camera inputs. It provides exceptional picture quality in both live and playback modes, and offers the following features: 16 Composite Video Input Connectors Compatible with Color (NTSC or PAL) and B&W (CCIR and EIA-170) Video Sources Auto Detection for NTSC and PAL H.
Operation Instruction Figure 1 — Typical DVR installation.
16-Channel Digital Video Recorder Chapter 2 — Installation Package Contents The package contains the following: Digital Video Recorder Power Adaptor and Power Cord Operation Instruction (This Document) Speco Central Software CD and Operation Instruction Infrared Remote Control Required Installation Tools No special tools are required to install the DVR. Refer to the installation manuals for the other items that make up part of your system. Figure 2 — DVR rear panel.
Operation Instruction Video Out Connect the main monitor to the Video Out connector. A VGA connector is provided so that you can use a standard, multi-sync computer monitor as your main monitor. Use the cable supplied with your monitor to connect it to the DVR. NOTE: The VGA and Video Out (BNC) connectors may be connected to individual monitors for simultaneous operation. Audio In/Out Your DVR can record audio from up to four sources.
16-Channel Digital Video Recorder RS485 Port The DVR can be controlled remotely by an external device or control system, such as a control keyboard, using RS485 half-duplex serial communications signals. The RS485 connector can also be used to control PTZ (pan, tilt, zoom) cameras or text-in devices. Connect RX+/TX+ and RX-/TX- of the control system to the P (+) and N (–) (respectively) of the DVR.
Operation Instruction To reset the unit, you will need a straightened paperclip: 1. Turn the DVR off. 2. Turn it on again. 3. While the DVR is initializing, the front panel LEDs will blink. When the front panel LEDs blink, poke the straightened paperclip into the unlabeled hole to the right of the VGA connector. 4. Hold the switch until all the LEDs on the front panel are lit. NOTE: When the DVR successfully resets to factory defaults all the LEDs on the front panel flash five times. 5.
16-Channel Digital Video Recorder Chapter 3 — Configuration NOTE: Your DVR should be completely installed before proceeding. Refer to Chapter 2 — Installation. Front Panel Controls Figure 3 — DVR front panel. Menu Button Copy Button Esc Button Play/Stop Button Camera Buttons Arrow Buttons Play/Pause Button HDD LED Power LED USB Port The front panel looks and operates much like a VCR combined with a multiplexer. The following describes each button and control.
Operation Instruction Play/Stop Button Pressing the PLAY/STOP button enters the playback mode, and pressing the button again exits the playback mode. When entering the playback mode, video is paused. Pressing the (Play/Pause) button plays back video at regular speed. The screen displays when the DVR is in the Pause mode and the screen displays when the DVR is playing back video. When in one of the multi-view formats, pressing this button enters the Triplex mode.
16-Channel Digital Video Recorder Remote Control Buttons ID Button Camera Buttons Sequence Button Login/Logout Button Arrow Buttons Menu Button Playback Buttons Alarm Button Layout Button Zoom Button PTZ Button Enter Button Esc Button PTZ Control Buttons Copy Button Play/Stop Button Figure 4 — Infrared remote control. NOTE: For simplicity, the button descriptions in this manual refer to the front panel buttons.
Operation Instruction Arrow Buttons These buttons are used to navigate through menus and GUI. You can also use them to change numbers by highlighting a number in the menu and using the Up and Down arrow buttons to increase or decrease the number’s value. When in the PIP display format, pressing the Up and Down arrow buttons moves the position of the small screen counter-clockwise and clockwise. Pressing the Left and Right buttons moves through screen pages in the Live Monitoring mode and Search mode.
16-Channel Digital Video Recorder PTZ Control Buttons While in the PTZ mode, the PRESET buttons are used to save Presets and load a Preset View, the ZOOM buttons are used to Zoom In and Zoom Out, and the FOCUS buttons are used for Near Focus and Far Focus. Copy Button Pressing the COPY button allows you to copy video clips. Play/Stop Button Pressing the PLAY/STOP button enters the playback mode, and pressing the button again exits the playback mode. When entering the playback mode, video is paused.
Operation Instruction Setup Screen Figure 7 — Setup screen. Press the MENU button or move the mouse pointer to the top of the screen and then select Monitoring menu to enter the setup screen. (Setup) in the Live While setting up the DVR, there will be many opportunities to enter names and titles. When making these entries, a Virtual Keyboard will appear. Use the arrow keys to highlight the character you want in the name or title and press the button.
16-Channel Digital Video Recorder In the Information screen, you can name the site location, assign a System ID number, select the language the screens are displayed in, display software version number, upgrade the software, show the System Log, display recorded time data, and clear all data. Highlight the Site box and press the button. A virtual keyboard appears that you can use to enter a Site Name. Once you have entered your title, highlight OK and press the button. Figure 9 — Information setup screen.
Operation Instruction Highlight Show System Log… and press the button to display the System Log. The System Log screen lists system activities (up to 5,000 from the latest) that have occurred along with the time and date. The icon will be displayed in the last column for system activities of the remote site. You can scroll through the log pages by using the Up and Down arrows, or you can go directly to a log page by entering the log page number in the box at the bottom left of the screen.
16-Channel Digital Video Recorder You can set up holidays by highlighting + and pressing the button. The current date appears. Highlight the month and day and change them by using the Up and Down arrow buttons. Press the button to add the date. Dates can be deleted by highlighting the beside the date and pressing the button. NOTE: Holidays that do not fall on the same date each year should be updated once the current year’s holiday has passed. Figure 11 — Holiday setup screen. Highlighting the Time Sync.
Operation Instruction Highlight the box in the Format column for the desired storage device and press the button. You will be able to format the device for recording. When selecting Not Using from Use As and highlighting the Format button, the device will not be used for recording. NOTE: The DVR does NOT support USB hard disk drives with a version lower than 2.0. The Information column displays whether the device is being used or not. Other indicates the device has been used for another DVR.
16-Channel Digital Video Recorder The +/- column is used to collapse and expand user groups. If there is a + or – in this column, it indicates the item is a Group Name. If there is a – in front of the Group Name, it indicates that the group has been “expanded” and all of the User Names within that group are displayed below the Group Name. If there is a + in front of the Group Name, it indicates that the group has been “collapsed” and all of the User Names within that group are hidden.
Operation Instruction To add a User, highlight the + User… box and press the button. A virtual keyboard appears allowing you to enter the User Name. Enter the name and assign the User to a Group and password. You can use camera buttons 1 to 9 on the front panel to assign the password. The password can be up to 8 digits. You will be asked to confirm the password.
16-Channel Digital Video Recorder Date/Time Setup Date: Set the system date and select the date format. Time: Set the system time and select the time format. Time Zone: Select your time zone. The Time Zone can be selected on the map. Use Daylight Saving Time: Selecting the box sets the system to use daylight saving time. NOTE: The Date/Time will be set, and the clock will start when you click the Next button.
Operation Instruction Select the Finish button to finish the EZ Record and select the Go to EZ Network button to start the EZ Network. If you selected the Go to EZ Network, select the Next button to start the EZ Network. Figure 18 — EZ Network screen. Internet Connection Select whether or not your DVR is connected to the Internet.
16-Channel Digital Video Recorder DVRNS Setup Use DVR Name Service: Select the box to use the DVR Name Service. DVRNS Server: Enter the IP address or domain name of the DVRNS server. Port: Set the port number of the DVRNS server. Use NAT: Select the box to use the NAT (Network Address Translation) device. DVR Name: Enter the DVR name to be registered on the DVRNS server. Check: Select the box to check whether or not the name you entered can be used.
Operation Instruction Highlighting Recycle and pressing the button toggles between On and Off. In the Recycle mode, the DVR records over the oldest video data once all available storage space has been used. When Recycle is turned off, the DVR stops recording once all available storage space has been used. Highlight the Event Record Dwell box and set the length of time you would like to record for the associated event. You can set the dwell from 5 seconds to 30 minutes.
16-Channel Digital Video Recorder Highlighting the Panic Recording – Quality and pressing the button allows you to set the recorded image quality for Panic recording. You can select from: Very High, High, Standard and Basic. Highlighting the Panic Recording – Resolution and pressing the button allows you to set the recorded image resolution for Panic recording. You can select from: Very High (D1), High (Half D1) and Standard (CIF).
Operation Instruction When the DVR is in the Time & Event mode, the DVR will follow the Time settings and the top-left corner of the screen. The DVR follows the Event settings and the icon displays. Highlight the box under the Channels heading and press the Mode Only) Highlight the box under the Settings heading and press the icon displays at the button to select which cameras will be recorded. (Simple button to define the recording settings.
16-Channel Digital Video Recorder When the DVR is in the Event Record mode it is possible to have it record images before the event occurs. The Pre-Event screen allows you to define how to handle pre-event recording. You can turn individual cameras On or Off for pre-event recording. The image speed can be set from 1.00 to 30.00 ips (25.
Operation Instruction Highlight the Actions 1 and Actions 2 tabs, and the Actions 1 and Actions 2 setup screens appear. You can set the actions the DVR will take whenever it senses an input on one of its alarm input connectors. Highlight the desired box under the Record heading, and press the button. A list of cameras appears. Select the cameras that you want the DVR to record whenever it detects an input on the associated alarm input.
16-Channel Digital Video Recorder Your DVR has built-in video motion detection. Video motion detection can be turned On or Off for each camera. Figure 30 — Motion Detection Settings screen. Highlighting the box under the Sensitivity heading and pressing the button allows you to adjust the DVR’s sensitivity to motion for Daytime and Nighttime independently. There are five settings with 1 being the least sensitive and 5 being the most sensitive.
Operation Instruction Highlight the box beside Daytime and press the button. Use the Up and Down arrow buttons to set the Daytime range. The DVR will consider the remaining time range as the Nighttime. Highlight the Actions 1 and Actions 2 tabs, and the Motion Detection Actions 1 and Actions 2 setup screens appear. The DVR can be set to react to motion detection differently for each camera.
16-Channel Digital Video Recorder Highlighting the box under the Video Loss Interval heading allows you to set the duration of a signal loss before the DVR will report a Video Loss. The DVR will not consider any signal loss from a camera to be a Video Loss if the detected signal loss is shorter than the interval set on this screen. Highlight Use Ignoring Time and press the button to toggle between On and Off. When set to On, the DVR will ignore video loss events occurring during the preset period.
Operation Instruction The DVR checks to see if anything is blinding a camera. Figure 35 — Video Blind Settings screen. Highlighting the box under the Sensitivity heading allows you to adjust the DVR’s sensitivity to video blind for Black and White independently from 0 (Never) and 1 (least sensitive) to 15 (most sensitive). NOTE: Video blind might NOT be detected for a camera with a very noisy image especially when set for low sensitivity values.
16-Channel Digital Video Recorder NOTE: For the Notify action, the notify item you select should be enabled in the Notification setup screen and the DVR should be registered in the Speco Central (Remote Administration System). Highlight the desired box under the PTZ heading, and press the button. A list of PTZ presets appears. Select the preset position for each PTZ camera, where you want PTZ cameras to move to when the DVR detects video blind on the selected camera’s input.
Operation Instruction Highlight the more line(s) box, and press the button. Select the number of additional lines of text that you want the DVR to record. You can choose from 0 to 10. Highlight the box beside Line Delimiter, and press the button. Use the virtual keyboard to enter the character(s) that the device uses to indicate the end of a line. Special characters can be created using ^ and a capital letter; e.g., ^J for NL (New Line), ^M for CR (Carriage Return).
16-Channel Digital Video Recorder The DVR can be configured to run self-diagnostics and report the results. Highlighting the box beside System and pressing the button allows you to select the interval that you want the DVR to run self-diagnostics on the system. You can select from 1 hr. to 30 days or Never. Figure 40 — Health Check screen Highlight the Setup... box beside Check Recording and press the button. The Check Recording screen appears.
Operation Instruction The DVR can be set to react to system events. System events can be associated with an Alarm-Out connector, sound the DVR’s internal buzzer, and/or notify a number of different devices. Highlight the Alarm-Out box beside the desired event (Check Recording, Check Alarm-In, Disk Almost Full, Disk Full, Disk Bad, Disk Temperature, or Disk S.M.A.R.T.), and press the button. A list of Alarm Outputs appears. You can associate as many Alarm-Outs with the Event as you wish.
16-Channel Digital Video Recorder Network Setup Figure 44 — Network menu. Network Highlight Network in the Network menu and press the button. Highlight the first box beside Remote Watch – bps/ips. Press the Up and Down arrow buttons to set the Transfer Speed from 50Kbps to 100Mbps. Highlight the second box beside Remote Watch – bps/ips. You can select the unit of measure for the transfer speed between: bps and ips. Press the button to set the transfer speed.
Operation Instruction Highlight the LAN tab, and the LAN screen displays. Highlight the box beside Type and press the button. You can select the type of network configuration from: Manual, DHCP and ADSL (with PPPoE). Select the desired type and press the button. Selecting Manual from the Type allows you to set up LAN parameters manually. Change the numbers by highlighting them and using the Up and Down arrow buttons to increase or decrease the number.
16-Channel Digital Video Recorder Selecting DHCP from the Type and highlighting Save button reads the current IP address of the DVR configured by DHCP (Dynamic Host Configuration Protocol) network. Highlight Auto (Default) and press the button to toggle between On and Off. When it is On, the DVR will obtain the IP address of the DNS server automatically. NOTE: Selecting Auto will only be enabled when the DVR is configured for DHCP or an ADSL network.
Operation Instruction Highlight the Check box and press the button to check whether or not the name you entered can be used. NOTE: The DVR name you entered should be checked by selecting Check, otherwise the DVRNS changes will not be saved. When entering no name or a name already registered on the DVRNS server, an error message displays. Highlighting Save and pressing the button registers the DVR on the DVRNS server.
16-Channel Digital Video Recorder The DVR can be set up to contact a computer running Speco Central (Remote Administration System) when an event occurs. Highlight the box under the No. heading and press the button to toggle between On and Off. You will only be able to change the IP addresses if No. is enabled. Highlight the IP Address box that you want to change and press the button. Use the arrow buttons to enter the IP address of the computer you want contacted during an event.
Operation Instruction Highlight the box beside Port and press the button. Use the arrow buttons to enter the SMTP Server port number obtained from your system administrator. The default port number is 25. Highlight Use SSL/TLS and press the button to toggle between On and Off. When it is On, the DVR can send an email via an SMTP server requiring SSL (Secure Sockets Layer) authentication. NOTE: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.
16-Channel Digital Video Recorder You can add and edit notification schedules on this screen. Highlight the + and press the button to add a schedule. Highlighting the boxes under the Column heading and pressing the button allows you to edit the information in those boxes. The Day box allows you to select the days that the notification schedule will be active. The choices are: Sun, Mon, Tue, Wed, Thu, Fri, Sat, M~F, Hol and All.
Operation Instruction You can turn the camera number On or Off, and you can change the Title of each camera using the virtual keyboard. You can also determine which cameras will display on the monitors by selecting Normal, Covert 1 or Covert 2 from a drop-down list in the Use column. NOTE: When selecting the Covert 1, the DVR displays the camera title and status icons on the covert video. When selecting the Covert 2, the DVR displays only camera title on the covert video. Figure 55 — Camera setup screen.
16-Channel Digital Video Recorder Audio Highlight Audio in the Devices menu and press the button. The Audio setup screen appears. The DVR can record up to four audio inputs. Highlight the box beside the input and press the button. A list of cameras appears, and you can select which camera you want associated with that audio input. Highlight Enable Audio-Out and press the button. This toggles between enabling and disabling audio out. Figure 57 — Audio setup screen.
Operation Instruction The Mode box allows you to set how the alarm reacts during the scheduled time. When set to On, the Alarm-Out is active during the scheduled time. When set to Event, the Alarm-Out is only active when there is an Event during the scheduled time. The Channels box allows you to set which alarm outputs will be active. You can also select the DVR’s internal buzzer. The box allows you to delete an alarm output schedule.
16-Channel Digital Video Recorder Highlight the box beside Channels and press the button. You can select the cameras with recorded audio you want to extract audio files from. Highlight the box beside From and press the button to toggle between On and Off. When set to Off, you can enter a specific Date and Time. When set to On, the search will be from the first recorded audio.
Operation Instruction Highlighting OSD Margin… and pressing the button displays how OSD text will be displayed on the monitor. You can adjust the horizontal and vertical margins so that text and icons will not be hidden beyond the edges of the monitor. Highlight the Main Monitor tab to switch to the Sequence screen. Highlight the box beside Mode and press the button. You can select between Full Sequence and Cameo Sequence.
16-Channel Digital Video Recorder Remote Control Highlight Remote Control in the Devices menu and press the button. The Remote Control setup screen allows you to select a port and make correct settings for a remote keyboard. Highlight the box beside Port and select from None, RS232 and RS485. If the RS232 port and RS485 port are in use for PTZ control, networking or text input, the remote keyboard cannot be configured.
Operation Instruction 48
16-Channel Digital Video Recorder Chapter 4 — Operation NOTE: This chapter assumes your DVR has been installed and configured. If it has not, please refer to Chapters 2 and 3. The DVR’s controls are similar to a VCR. As with a VCR, the main functions are recording and playing back video. However, you have much greater control over recording and playing back video. You can establish recording schedules based on time of day and day of the week.
Operation Instruction Camera: Selecting Camera and choosing the camera number displays the selected camera full screen. It is the same as pressing the individual camera buttons on the front panel or clicking the left mouse button on a camera image when in one of the multiview formats (i.e., 2x2, 1P5, 1P7, 3x3 or 4x4). Clicking the left mouse button on the screen again returns to the previous display mode.
16-Channel Digital Video Recorder PTZ: Selecting PTZ and choosing the camera number allows you to control the selected camera as long as it has Pan, Tilt and Zoom capabilities. Refer to the following PTZ Mode section for details. Zoom: Selecting Zoom and choosing the camera number zooms the current image of the selected camera on the screen. Refer to the following Zoom Mode section for details. Audio: Selecting Audio toggles audio output On and Off.
Operation Instruction Active Cameo Mode (Display) Edit Group in the Live Monitoring menu in any You can enter the Active Cameo mode by selecting multi-view format. The yellow outline surrounding the video indicates the active cameo, and pressing the arrow buttons moves the active cameo. Selecting (Display) Edit Group again in any multi-view format, or pressing the (Play/Pause) button exits the Active Cameo mode.
16-Channel Digital Video Recorder You can save camera position settings as “presets” so that you can go directly to desired views. Once you have the camera at the desired settings, press the PRESET SET button, and the Set Preset dialog box will appear. Select the number you want to assign to the preset and press the (Play/Pause) button. Use the virtual keyboard to enter the preset name. Press the PRESET SELECT button to load the PTZ preset and the Move to Preset dialog box will appear.
Operation Instruction Covert Camera If a camera is set up as Covert 1 in the Camera setup screen (Settings tab), that camera will not be displayed unless a user with Covert Camera View authority logs into the system. However the camera title and status icons will be displayed on the monitor. If a camera is set up as Covert 2 in the Camera setup screen (Settings tab), that camera appears to be Off unless a user with Covert Camera View authority logs into the system.
16-Channel Digital Video Recorder Selecting All Channels plays back video of all cameras. The DVR maintains the same display format as it does in the live mode except for the PIP format. You can also change the screen layout in the same way as you do in the live mode. Selecting the camera number under Triplex enters the Triplex mode and plays back video of the selected camera.
Operation Instruction Display Search Go To Bookmark Export Camera Menu Alarm Digital Deterrent Panic Data Source Exit Figure 69 — Search menu. NOTE: The Search menu also can be displayed by moving the mouse pointer to the top of the screen. Search Menu Display Selecting (Display) in the Search menu displays the following Display Menu. Camera: Selecting Camera and choosing the camera number displays the selected camera full screen.
16-Channel Digital Video Recorder Move the cursor over the date and time and press the (Play/Pause) button. You can use the Left and Right arrow buttons to highlight the year, month, day, hours, minutes and seconds. Use the Up and Down arrow buttons to change to the date and time you want to search for video. Once you have set the date and time you want, press the button. Then highlight Go and press the button. The selected date and time will display.
Operation Instruction Data Source (Data Source) in the Search menu allows you to select the data source to be searched. Selecting Record Selecting searches recorded data on primary storage installed in the DVR, and selecting Other searches recorded data on storage used for another DVR then installed in this DVR. Exit Selecting (Exit) in the Search menu exits the search mode and enters the live monitoring mode. Event Log Search The DVR maintains a log of each time the Alarm Input port is activated.
16-Channel Digital Video Recorder Highlight the box beside Video Loss and press the reports of lost video. button. You can select the cameras for which you want any Highlight the box beside Video Blind and press the reports of blind video. button. You can select the cameras for which you want any Highlight the box beside Text-In and press the of text input. button. You can select the text-in devices which you want any reports Highlight the box beside Record Channels and press the button.
Operation Instruction Selecting or located at the bottom zooms the record table. Selecting displays eight hours (1-minute based), and selecting displays 24 hours (3-minute based) at once. To move to earlier or later times that are not shown in the current record table screen, select the arrows located at the end of the times by using the arrow buttons on the front panel.
16-Channel Digital Video Recorder Motion Search The Motion Search… can be selected from the Search menu while the DVR displays the camera full screen. The Motion Search screen displays a list of motion events. Use the arrow buttons to highlight the event for which you would like to see video and press the (Play/Pause) button to display the video associated with the selected event on the small search screen.
Operation Instruction Text-In Search The DVR maintains a log of each time there is Text Input. The Text-In Search screen displays this list. Use the arrow buttons to highlight the event for which you would like to see video. Pressing the (Play/Pause) button will extract the video associated with the Text Input and display the first image of the event. Pressing the button will start playing the “event” video segment. Pressing the PLAY/STOP button returns to live monitoring.
16-Channel Digital Video Recorder Bookmarks The Bookmarks screen can also be accessed by selecting (Bookmark) in the Search menu when in playback mode. Highlight + and press the (Play/Pause) button to add the current playback point to the bookmark list. Highlight the Title box and enter the name of the registered bookmark. Use the virtual keyboard to enter the bookmark name. NOTE: Up to 64 bookmarks can be registered.
Operation Instruction CAUTION: The USB device for clip copy must be FAT 16 or FAT32 format. The DVR automatically assigns a file name to the video clip. However, you can give the video clip file a different name. Highlight the box beside File Name and press the button. A virtual keyboard appears. Enter a file name for the video you are backing up and select Close. The DVR will automatically add the camera number (for example “01”) and “.exe” to the file name.
16-Channel Digital Video Recorder Appendix USB Hard Disk Drive Preparation Preparing the USB hard disk drive in Windows 2000 NOTE: Preparing a USB hard disk drive under Windows XP, Window Vista and Window 7 is almost identical to Windows 2000. 1. 2. 3. 4. 5. 6. NOTE: Connect the USB hard disk drive to your computer using the USB Cable. Turn on your computer. The USB device icon should display on the Taskbar.
Operation Instruction Text-In Search Examples Search Example I 1 2 3 4 5 6 123456789012345678901234567890123456789012345678901234567890 Item Unit price Qty amount ================================================== Coke | $ 2.20 | 1(s) | $ 2.20 Fanta | $ 2.20 | 1(s) | $ 2.20 Hotdog | $ 3.50 | 3(s) | $ 10.50 Pepsi | $ 1.95 | 1(s) | $ 1.95 ================================================== total : $ 16.
16-Channel Digital Video Recorder For example, if you want to search for Coke with a Qty (Quantity) of more than 1 and Hotdog with an amount totaling over $8, the following search condition can be set. Speco Remote Speco Remote allows you to access a remote DVR, monitor live video images and search recorded video using Internet Explorer web browser anytime from virtually anywhere.
Operation Instruction NOTE: There might be a problem that the bottom of Speco Remote page is cropped due to the address or status bars in Microsoft Internet Explorer 7.0. In this situation, it is recommended that websites open windows without address or status bars by changing the internet setting.
16-Channel Digital Video Recorder ⑦ Click the to adjust the brightness, contrast, saturation and hue of monitoring image. ⑧ Click the to control pan, tilt and zoom of the camera from a remote site. ⑨ Click the to control alarm out devices at the remote site. ⑩ Click the to set up the image drawing mode and OSD display. You can adjust the display speed by changing the image drawing mode, and select OSD information to be displayed on the screen.
Operation Instruction ① Click the to log out the Speco Remote program. ② Click the to access to the web monitoring mode. ③ Position the mouse pointer on the Remote Search logo to see the version of the Speco Remote program. ④ The DVR information window displays the time information of recorded data on the remote DVR and login information of Speco Remote. ⑤ Click the to blur, sharpen, equalize and interpolate playback images. Click the to zoom to adjust the brightness of the recorded images.
16-Channel Digital Video Recorder ⑭ Selecting a camera on the screen and clicking the right mouse button displays the text menu screen. Change Camera Title: Changes the camera name. Enable Audio: Plays audio while playing back recorded video that has recorded audio. (Single-Screen Layout Only) Aspect Ratio: Changes the image aspect ratio. Deinterlacing: Using a deinterlace filter for interlaced video enhances image display quality by eliminating horizontal scan lines and noise in areas with motion.
Operation Instruction Map of Screens 72
16-Channel Digital Video Recorder Troubleshooting Problem Possible Solution No Power Check power cord connections. Confirm that there is power at the outlet. No Live Video DVR has stopped recording If hard disk drive is full, you will either need to delete video or set the DVR to the Overwrite Mode. The icon displays, however, the DVR is not recording. When the DVR is in the Pre-Event recording mode, the yellow and display when there is no event, and the DVR is not recording.
Operation Instruction Error Code Notices No. 0 1 2 3 4 100 101 102 103 104 105 300 301 302 303 304 400 401 402 403 404 405 500 System Upgrade Related Description Unknown error. File version error. Operating system version error. Software version error. Kernel version error. Upgrade device mounting failed. Package is not found. Extracting package failed. LILO failed. Rebooting failed. Invalid package. Remote connection failed. Remote network error. Remote upgrade is not authorized.
16-Channel Digital Video Recorder Alarm Input Alarm Output Internal Buzzer Network Connectivity Audio Input Audio Output Text Input INPUTS/OUTPUTS 16 terminal, programmable as NC or NO, 2.4V (NC) or 0.