Installation Sheet

ManualsBrandsSpeakman ManualsSafety AccessoriesOptimus Eye and Face Wash Bowl Combination Emergency Shower System

INSTRUCTIONS FOR MODELS

NEED HELP?

TOOLS AND SUPPLIES

IMPORTANT

For ADA installation see Page 6.

Use Thread Locker or Sealant on ALL

threaded connections

SAFETY TIPS

MAINTENANCE

WARRANTY

3 year limited warranty.

Additional warranty information can be found at:

www.speakmancompany.com

For additional assistance or service please contact:

SPEAKMAN

Company

400 Anchor Mill Road

New Castle, DE 19720

800-537-2107

customerservice@speakmancompany.com

www.speakmancompany.com

STANDARD INSTALLATION - FOR ADA INSTALLATION SEE PAGE 6 PG.1

SE-1200

SE-1250

SE-1255

OPTIMUS

™

92-SE-1200-1255-R4

Level Adjustable

Wrench

Pipe

Wrench

7/16” Hex Key

Wrench

Strap

Wrench

Mounting

Hardware

(not included)

ANSI Z358.1 requires that all safety emergency

equipment shall be activated on a weekly basis to flush

the line and verify proper operation. SPEAKMAN

furnishes a testing record tag (91-0635) with each unit.

On this tag, the date of inspection and the inspector’s

initials should be noted. ANSI Z358.1 specifies that the

height of the spray heads is to be between 33” - 45”

from the floor. Use Thread Locker or Sealant on all

threaded connections. Be sure the Unit is level and

plum.

Cover your drain to prevent loss of parts. Always wear

eye protection.

Should you need parts to repair this unit, please

reference the parts listing for correct repair part

number. Before any maintenance is done, be sure to

shut the water supply off. Use only genuine

SPEAKMAN parts when repairing or replacing

components. To order parts, call 1-800-537-2107.

At desired location, mount Floor Flange

on a flat, level surface using suitable

anchors, making sure that one of the three

ears on the Floor Flange is positioned at

what will be the front of the Stanchion.

The Unit should be placed so that there is

sufficient unobstructed area around the

Stanchion.

Assemble

1-1/4” x 32-3/8” Pipe to Floor

Flange .

Thread 1-1/4” x 1/2” Drain/Supply Cross

onto Pipe . Side Outlets should face

the front and back of the Unit, and the

1/2” male threaded outlet upward at 45°

to the right side of the Unit.

Front of Unit

1/2” Male

Threading

Assemble 1-1/4” x 26-7/16” Pipe to

Drain/Supply Cross . Assemble

1-1/4”

Tee to Pipe .

Assure the Side Outlet portion of Tee

is facing the rear of the Unit.

Rear of Unit

Front of Unit

STANDARD INSTALLATION

(FOR ADA INSTALLATION SEE PAGE 6)

Summary of content (11 pages)

PAGE 1
INSTRUCTIONS FOR MODELS OPTIMUS™ TOOLS AND SUPPLIES Level Adjustable Wrench Pipe Wrench Use Thread Locker or Sealant on ALL threaded connections At desired location, mount Floor Flange 13 on a flat, level surface using suitable anchors, making sure that one of the three ears on the Floor Flange is positioned at what will be the front of the Stanchion.
PAGE 2
If water supply is coming from above Unit, install Plug 7 into side outlet of Tee 10 . If water supply is coming from behind Unit, install Plug 7 into top outlet of Tee 8 . Assemble 1” x 4-1/2” Pipe 6 into Side Outlet of Tee 8 . Review View 4a below to understand the orientation of Ball Valve 5 . Assemble 1” Ball Valve 5 onto Pipe 6 . Valve Stops must be aligned correctly in order for the Pull Handle to operate properly. 7 8 Insert Flow Control 4 into Floet Housing 3 , referring to Detail View 5a.
PAGE 3
Thread Pipe 12 . 21 into Drain/Supply Cross Thread entire Bowl Assembly 22 to Pipe 21 , being sure Bowl is level, plumb, and horizontal when completely secured. Install Paddle Handle 24 to Ball Valve using Nylo-Hex Nut Nut 25 . Assemble male end of Flex Hose Valve 23 (Detail View 8a). 15 to Ball Assemble female end of Flex Hose 15 to Drain/Supply Cross 12 (Detail View 8b). 23 Detail View 8a 22 Connect an uninterruptible potable water supply with a minimum of 30psi flowing pressure to Water Inlet.
PAGE 4
STANDARD INSTALLATION EXPLODED VIEW / REPAIR PART GROUPS 4 5 6 3 7 2 1 8 14 17 19 16 9 18 10 20 11 22 15 24 12 Item No. Description Qty. 1 2 3 4 5.1 5.2 6 7 8 9 10 11 12 13 14 15 16.1 16.2 17 18 19 20.1 20.2 21 22 22.1 22.2 22.3 23 23.1 23.2 24 25 29 1" x 90 Galv. Street Elbow 1" x 19-3/8" Galv. Pipe, TBE Rubber Floet Housing 20 GPM Flow Control 1" Chrome Plated Brass Ball Valve 1" Stainless Steel Ball Valve 1" 4-1/2" Galv. Pipe, TBE 1-1/4" Galv. Plug 1-1/4" x 1-1/4" x 1" Galv.
PAGE 5
STANDARD INSTALLATION ROUGH-IN DIMENSIONS SE-1200/1250/1255 SHOWER FLOW DATA PRESSURE 5 31 3 "±8 " 4 806mm±16 3 27 3 "±4 " 4 705mm±19 FLOW RATE psi bar gpm L/min 30 2.07 20 75 60 4.14 25 94 8"± 1 " 16 203mm±2 SE-1200/1250/1255 EYE/FACEWASH FLOW DATA PRESSURE 1-1/4" NPT FEMALE INLET FLOW RATE psi bar gpm L/min 30 2.07 4.9 18.5 60 4.14 5.0 18.9 1-1/4" NPT (TOP) FEMALE INLET 3 8 7 "±8 " 8 225mm±10 NOTE: ALL UNITS MEET EXISTING ANSI Z358.1 STANDARDS AND OSHA RULES.
PAGE 6
INSTRUCTIONS FOR MODELS OPTIMUS™ TOOLS AND SUPPLIES Level Adjustable Wrench Pipe Wrench SE-1200 SE-1250 SE-1255 For Standard installation see Page 1. Use Thread Locker or Sealant on ALL threaded connections At desired location, mount Floor Flange 13 on a flat, level surface using suitable anchors, making sure that one of the three ears on the Floor Flange is positioned at what will be the front of the Stanchion.
PAGE 7
If water supply is coming from above Unit, install Plug 7 into side outlet of Tee 10 . Assemble 1” x 4-1/2” Pipe 6 into Side Outlet of Tee 8 . Review View 4a below to understand the orientation of Ball Valve 5 . If water supply is coming from behind Unit, install Plug 7 into top outlet of Tee 8 . Assemble 1” Ball Valve 5 onto Pipe 6 . Valve Stops must be aligned correctly in order for the Pull Handle to operate properly.
PAGE 8
Assemble Pull Rod 20 to Pull Rod Extension 26 using Machine Screw 27 and Nylo-Hex Nut 28 . Thread Pipe 12 . 21 into Drain/Supply Cross Thread entire Bowl Assembly 22 to Pipe 21 , being sure Bowl is level, plumb, and horizontal when completely secured. 28 27 Install Paddle Handle 24 to Ball Valve using Nylo-Hex Nut Nut 25 . Assemble male end of Flex Hose Valve 23 (Detail View 8a). 15 to Ball Assemble female end of Flex Hose 15 to Drain/Supply Cross 12 (Detail View 8b).
PAGE 9
ADA INSTALLATION EXPLODED VIEW / REPAIR PART GROUPS 5 4 6 3 7 2 1 14 8 9 19 17 18 16 26 10 27 28 29 20 22 15 24 12 Item No. Description Qty. 1 2 3 4 5.1 5.2 6 7 8 9 10 11 12 13 14 15 16.1 16.2 17 18 19 20.1 20.2 21 22 22.1 22.2 22.3 23 23.1 23.2 24 25 26.1* 26.2* 27* 28* 29 1" x 90 Galv. Street Elbow 1" x 19-3/8" Galv. Pipe, TBE Rubber Floet Housing 20 GPM Flow Control 1" Chrome Plated Brass Ball Valve 1" Stainless Steel Ball Valve 1" 4-1/2" Galv. Pipe, TBE 1-1/4" Galv.
PAGE 10
ADA INSTALLATION ROUGH-IN DIMENSIONS SE-1200/1250/1255 SHOWER FLOW DATA PRESSURE 31 3 " 4 806.32mm 27 3 " 4 704.72mm FLOW RATE psi bar gpm L/min 30 2.07 20 75 60 4.14 25 94 SE-1200/1250/1255 EYE/FACEWASH FLOW DATA PRESSURE 1-1/4" NPT (TOP) FEMALE INLET 8"± 1 " 16 203.20mm±2 1-1/4" NPT FEMALE INLET FLOW RATE psi bar gpm L/min 30 2.07 4.9 18.5 60 4.14 5.0 18.9 91 23 "±1" 32 2329.92mm±25 NOTE: ALL UNITS MEET EXISTING ANSI Z358.1 STANDARDS AND OSHA RULES.
PAGE 11
To Clean the Aerated Outlets: To Clean the In-Line Strainer: Using the Aerator Wrench 1 , remove the Aerator 2 . The Flow Control Housing 3 will come out next, with the Flow Control 4 inside of it. Remove the Flow Control and check for debris surrounding the o-ring. Flush with clean water. Check the mesh on the back of the Aerator for debris. Flush with clean water. Begin by removing Supply Hose 3 from Hose Manifold Tee 1 . The Strainer 2 will be located inside the threading of Supply Hose 3 .