Owner`s manual

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-4.0 • LINEAR P/N: 223110B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 14.000” FOLD TO 4.250” X 3.500”
• FOLDING: 4 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223110B • IMAGE 1
DESCRIPTION
The IRE-4.0 is the dual emitter version of the IRE-3.0. It features a
unique EZ-Docker
™
plate that permits instant removal of the emit-
ter when rearranging or servicing components. It flashes visible red
when emitting IR control signals. It has 75% lower IR output than
non-visible emitters and therefore should be used when controlling
multi-zone components to avoid cross-zone interaction. An improved
adhesive reduces callbacks for reattachment of “fallen emitters”.
ATTACHMENT
First, locate the component’s IR Sensor window (see Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
™
port has a clear adhesive layer on its bottom surface.
Peel the protective
layer off, exposing
the adhesive.
Orient the port vertical
(see Fig. 2) and press
it over the center of the
component’s sensor
window. Press & hold
for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZ-
Docker
™
port. You should
feel it “snap” into place.
IRE-4.0
Dual Emitter
with Visible LED
8 FT
9/16"
7/16"
3.5mm
mini plug
Emitters &
Docking Ports
7/16"
(– )
(+
)
Top View
NOTE: White striped
side is positive ( +
)
1/4"
Side View
Emitter
Emitter slides into
Docking Por
t
Wire L ead
Docking
Por
t
Clear Adhesive Tape
(See Note 3)
Fig. 1
TYPICAL INSTALLATION
Satellite Receiver
PS-1.0
IRE-4.0
Dual Emitter
with Visible LED
IRE-1.0
Emitter
IRE-4.0
Dual Emitter
with Visible LED
A/V Receiver
VCR
Hand Held
Remote
IRC-3.0
IR Sensor
Window
AT-1.0
Amplified Terminator
Unit
Power Supply
120V AC
(unswitched)
Shelf Top
IR Receiver
Fig. 3
Fig. 1
(To remove the emitter at any time, simply push upward until it
“pops” out).
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
™
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-4.0 shell.
Note 3: If you need to remove the EZ-Docker
™
port or emitter previ-
ously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.
Fig. 3
IR Controlled Components
IR Sensor
window
Docking Port
IRE-4.0 attached to
IR sensor window
2) Slide IRE-4.0 Emitter
end into docking port
1) Attach IRE-4.0 Docking Port to
IR sensor window with adhesive pad
Fig. 2
Fig. 2