Owner`s manual

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-3.0 • LINEAR P/N: 223105B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 14.000” FOLD TO 4.250” X 3.500”
• FOLDING: 4 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223105B • IMAGE 1
DESCRIPTION
The IRE-3.0 represents the highest level in sophistication for attachable
IR Emitters. It features a unique EZ-Docker
™
port that permits instant
removal of the emitter when rearranging or servicing components. It
flashes visible red when emitting IR control signals. It has 75% lower
IR output than non-visible emitters and therefore should be used
when controlling multi-zone components to avoid cross-zone interac
-
tion. An improved adhesive reduces callbacks for reattachment of
“fallen emitters”.
ATTACHMENT
First, locate the component’s IR Sensor window (See Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
™
port has a clear adhesive layer on its bottom
surface. Peel the protec
-
tive layer off, exposing
the adhesive.
Orient the port vertical
(see Fig. 2) and press
it over the center of the
component’s sensor
window. Press & hold
for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZ-
Docker
™
port. You should
feel it “snap” into place.
IRE-3.0
Emitter with
Visible LED
8 FT
9/16"
7/16"
3.5mm
mini plug
1/4"
Side View
Emitter
Wire Lead
Dockin
g
Por
t
Clear Adhesive Tape
(See Note 3)
Top View
NOTE: White striped
side is positive ( +)
(–
)
(+
)
Emitter slides into
Docking Por
t
Fig. 1
TYPICAL INSTALLATION
Satellite Receiver
A/V Receiver
PS-1.0
IRE-3.0
Emitter w/
Visible LED
IRE-3.0
Emitter w/
Visible LED
IRE-3.0
Emitter w/
Visible LE
D
VCR
Hand Held
Remote
IRC-3.0
IR Sensor
Window
AT-1. 0
Amplified Terminator
Unit
Power Supply
120V AC
(unswitched)
Shelf Top
IR Receiver
Fig. 3
Fig. 1
(To remove the emitter at any time, simply push upward until it
“pops” out).
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
™
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-3.0 shell.
Note 3: If you need to remove the EZ-Docker
™
port or emitter
previously stuck to a component’s surface, use a fresh adhesive
(included) before reattaching.
Fig. 3
IR Controlled Components
IR sensor
window
Docking Por
t
IRE-3.0 attached to
IR sensor window
2) Slide IRE-3.0 Emitter
end into docking por
t
1) Attach IRE-3.0 Docking Port to
IR sensor window with adhesive pad
Fig. 2
Fig. 2