Owner`s manual

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-2.0 • LINEAR P/N: 223109B • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.25” X 17.500” FOLD TO 4.250” X 3.500”
• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223109B • IMAGE 1
DESCRIPTION
The IRE-2.0 is the dual emitter version of the IRE-1.0. It features a
unique EZ-Docker
™
port that permits instant removal of the emitter
when rearranging or servicing components. An improved adhesive
reduces callbacks for reattachment of “fallen emitters”. The case may
also be taken apart so that the tiny internal emitter can be placed
inside a component, when desired. High IR output from the top
curved surface allows emitter to be mounted on a nearby surface,
below, above or on a cabinet door, rather than directly on the sensor
of the unit where conditions permit.
ATTACHMENT
First, locate the component’s IR Sensor window (see Note 1) and
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker
™
port has a clear adhesive layer on its bottom surface.
Peel the protective layer
off, exposing the adhesive.
Orient the port vertical (see
Fig. 2) and press it over the
center of the component’s
sensor window. Press &
hold for several seconds to
ensure maximum contact
of the adhesive.
Insert the 3.5mm plug
into an Emitter jack on a
SpeakerCraft Terminator or
other source of IR (see Fig.
3). Slide the emitter from
the top down, into the EZ-
Docker
™
port.
IRE-2.0
Dual Emitter
8 FT
9/16 "
7/16 "
3.5mm
mini plug
Emitters &
Docking Ports
7/16 "
(– )
(+)
Top View
NOTE: White striped
side is positive ( +
)
1/4"
Side View
Emit ter
Emit ter slides int o
Dock ing Port
Wire Lead
Dock ing
Port
Clea r Adhesive Tap e
(See Note 3)
TYPICAL INSTALLATION
Satellite Receiver
PS-1.0
IRE-2.0
Dual Emitter
IRE-2.0
Dual Emitter
IRE-1.0
Emitter
A/V Receiver
VCR
Hand Held
Remote
IRC-3.0
IR Sensor
Window
AT-1.0
Amplified Terminator
Unit
Shelf Top
IR Receiver
Power Supply
120V AC
(unswitched)
Fig. 3
Fig. 1
You should feel it “snap” into place. (To remove the emitter at any
time, simply push upward until it “pops” out).
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
™
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-2.0 shell.
Note 3: If you need to remove the EZ-Docker
™
port or emitter previ-
ously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.
Fig. 3
IR Controlled Components
IR sensor
window
Docking Port
IRE-2.0 attached to
IR sensor window
2) Slide IRE-2.
0 Emitter
end into docking port
1) Attach
IRE-2.0 Docking Port
to IR sensor window with adhesive pa
d
Fig. 2
Fig. 2