WPEQ-256ACNRBI WPEQ-256ACN 1
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] Product Introduction Standard IEEE802.11ac/a/b/g/n Chipset solution QCA9892-BR4B Radio stream [Note1] 2T2R Antenna type / connector. External with IPEX connector Bus Interface PCI Express Form Factor Mini-PCIe 802.11b: 11, 5.5, 2, 1 Mbps; 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz Data Rate 802.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] 802.11a: 14dBm@54Mbps 802.11b: 20dBm@11Mbps Transmit Output Power (Tolerance: +/-2dBm) 802.11g: 16dBm@54Mbps 802.11gn HT20: 15dBm@MCS7 802.11gn HT40: 15dBm@MCS7 802.11an HT20: 13dBm@MCS7 802.11an HT40: 13dBm@MCS7 802.11ac VHT80: 10dBm@MCS9 802.11a: ≤-74dBm@54Mbps 802.11b: ≤-87dBm@11Mbps 802.11g: ≤-74dBm@54Mbps Receiver Sensitivity 802.11gn HT20: ≤-70dBm@MCS7 802.11gn HT40: ≤-68dBm@MCS7 802.11an HT20: ≤-71dBm@MCS7 802.11an HT40: ≤-68dBm@MCS7 802.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] 2. Hardware Specification 2.1 Hardware Dimension Dimension: 50.8mm * 29.85mm * 4.1mm(±0.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] 2.3 Pin Assignment The following section illustrate signal pin-outs for the system connector. Pin# Pin Name Description Pin# Pin Name Description 2 +3.3V +3.3V GND 1 WAKE_L(NA) Output and open Drain active Low signal. This signal is used to request that the system return from a sleep/suspended state to service a function initiated wake event.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] this signal requires a pull-up resistor on the card Input signal for 21 GND GND 22 PERST_L functional reset to the card PCI Express x1 data 23 PERn0 interface: one differential 24 +3.3V +3.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] * NA: No active * OPT: Optional (Depends on S/W and H/W design of the module and customer platform main board, functionalities of end devices and drivers.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] 15.407(a)(1)(i). The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; IC Radiation Exposure Statement: This equipment complies with IC RSS
PRODUCT APPROVAL SHEET –WPEQ-256ACNRBI [W] The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. Japan Antenna List Connector Brand Model 1 Walsin RFDPA131000SBLB808 I-Pex Dipole 2 Cortec AN2450-5511BRS I-Pex Dipole 3 SANSEI ANTDP-027A0 I-Pex Dipole 1.3 4 Taoglas MA231.LBC.
