1. Light Sensor 2. Wide-angle Lens 3. Red / Blue Lights 4. Motion Sensor 5. Microphones 6.
Blue Indicator Light Blue light Live view Flashing blue Motion detection Astor Rechargeable Soar Para + Battery Camera 6000mAh Mounting arm Battery Pack Astor 7 Anchors / Mounting User Mania Screws
Charge the Included battery. Fully charge the battery by plugging it into a USE port using a Micro USE cable. It takes about 6-8 hours for the battery to Tull charge. When only one blue LED is IIL, halt Indicates the battery 's Tull charged. @& © = Charging @ = Fully Charged 1. Remove the battery cover. Twist the battery cover counterclockwise to unlock, and then remove It from your Astor.
2. insert a Micros D card. Insert a Micros D card (AGB — 32GB} into the the card slot with the label facing the battler compartment. You can sol the card by pressing It into the slot with your mailing. 3. Insert the battery. Insert the fully charged battery into the bottom of your Astor until it clicks into place. 4. Set up your device in the Wit app. Before You Start 1. Download and install Wit App. Scan the GR code below or search for Wait on the Apple App Store or Google Play.
2. Create an Wit account. 108 / Android App Download Set up your Astor in the Al wit app. To pale your Astor, follow the steps below and in—app instructions. 1. Open Wait App and log in to your account. 2. To add your camera, select the + icon. 3. Select Battery Camera 2. 4. Press and hold the Setup Button until the red light 1s Mashing. Bb. Enter your 2.40Hz WI-Fi network and the WI-Fi password, then tap Next (GHz is not supported). 6.
5. Attach the battery cover, Find the Open lock symbol located behind our Astor. Align the symbol with the line on the battery cover. Push the cover on and turn clockwise until it locks. 8. Give ita trv! After setup, tap the Live View In the Wait app to see live video from your Astor. Choose any location. Place the Astor anywhere, inside or outside your home. It can be mounted on a wall, ceiling, or placed on a tabletop. Put it in an area whets you wish 1o view.
Using the axis to rotate the stand, position the base above the camera. Ensure the bees 's directly positioned above your Astor. The base is hinged, so rotate the base behind the Astor prior to wall Installation.
Once you have chosen a wall or a ceiling Tor your Astor, Mark drill heels and use a bit to drill holes In your wall or ceiling. Insert anchors and secure your Astor with mounting screws. Flip the base under the Astor, so it can stand upright. Use the flicked base as a stand for table or shelf placement. Installation is compete.
If you experience some issues during the app setup, try these steps: Check your WiFi password. The most common Issue during setup is incorrect WI-Fi passwords. Passwords are case sensitive. Please double-check your password. Reboot the router/modem. f you have entered the correct password, but still experiencing issues, try unplugging the power to your router/modem. Wait for 30 seconds, then plug the power back and turn it back on. Proceed to sen again in tne Aw app.
Share via GR Code: 1. Open the Wit App on a new user's smartphone. 2. From the home page, tap +. 3. Tap GR Code Sharing, (nen scan the GR code the device owner generated before. 4. You will see Share successful, then tap Confirm. How many users can view the video at the same time? Up to 3 users may view the video feed, but only 7 user can use the direct intercom. Both 108 and Android are compatible ls GHz WI-Fi supported? No. Only 2.4GHz WI-F is supported.
1. Open Settings. Go to Wait app permissions and select Notifications. 2. Make sure all switches are on. What size Micros D card should | use? This device is compatible with 4CB, 8GB, 18CB and 32CB capacity micros D cards. We recommend only purchasing name brand micros D cars through official resellers. Please compete the battery camera setup in the App prior to installing the solar panel. 1. Choose the Installation location Fisk an unshaped spot for best sun exposure.
3. Drill the hoes Optional: You may opt to use a drill bit to drill the holes where you have previously marked. = For mounting surfaces that are brick, concrete, or stucco, please use the plastic anchors. You may need to use a hammer to Install the anchors. « For mounting surfaces that ars wood or vinyl, you can omit the anchors, and use the screws directly. 4. Install the mounting arm Use a screwdriver 10 secure the mounting arm to the wall, Tighten securely. £.
FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.