Square Duct Board Installation Manual

ManualsBrandsSpacePak ManualsAccessoriesPlenum Hole Cutter

SECTION 1: INTRODUCTION ................................ 1

Square Fiberboard Plenum Duct Components .... 2

SECTION 2: INSTALLATION .................................. 2

Step 1 and 2: ........................................................... 1

Step 3: Attaching Supply Air Plenum Adaptor ........ 2

Horizontal Discharge ............................................ 2

Vertical Discharge ............................................... 2-3

Step 4: Installing Air Distibution Components ........ 3

Plenum Duct Installation ...................................... 3-4

Plenum Take-Off Installation ................................ 4

IN UNITED STATES: 260 NORTH ELM ST. WESTFIELD, MA 01085 (413) 564-5530/FAX (413) 564-5815

IN CANADA: 7555 TRANMERE DRIVE, MISSISSAUGA, ONTARIO, L5S 1L4 (905) 672-2991/FAX (905) 672-2883

SQUARE

FIBERBOARD

PLENUM DUCT

INSTALLATION

MANUAL

SDBMG2-311

W30-WG0377-02

1/11

SECTION 1: INTRODUCTION

The following terms are used throughout this

manual to bring attention to the presence of potential

hazards or to important information concerning the

product:

NOTICE: Used to notify of special instructions on

installation, operation or maintenance which are

important to equipment but not related to personal

injury hazards.

STEPS 1 AND 2: REFER TO FAN COIL UNIT INSTALLATION MANUAL

SECTION 2: INSTALLATION

Summary of content (4 pages)

PAGE 1
SDBMG2-311 W30-WG0377-02 SQUARE FIBERBOARD PLENUM DUCT INSTALLATION MANUAL SECTION 1: INTRODUCTION ................................ Square Fiberboard Plenum Duct Components .... SECTION 2: INSTALLATION .................................. Step 1 and 2: ........................................................... Step 3: Attaching Supply Air Plenum Adaptor ........ 1 2 2 1 2 Horizontal Discharge ............................................ 2 Vertical Discharge ...............................................
PAGE 2
Plenum Elbow BM-3004 Plenum Tee BM-3002 Balancing Orifice 27-6123 (15%) 27-6124 (35%) 27-6125 (50%) Kwik Connects BM-6818 End Cap BM-3003 Plenum Duct BM-3001 Sound Attenuating Tubing BM-6926 Plenum Adapter BM-3007 Insulated Elbow AC-KCWE Fan Coil Unit (See Legend) Square Supply Tubing Plenum AC-ST6-100 Take-off BM-3008 Terminator Plates BM-6845 Winter Supply Air Shut-off BM-6819 Return Air Duct 2 BM-6808-10 3 BM-6809-10 4 BM-6839-10 Drain Pan 2 ACS-BASE-2 3 ACS-BASE-3 4 ACS-BASE-5 Duct Strap Legen
PAGE 3
14. Assure blower wheel is centered in inlet and discharge of blower housing. If required, adjust by loosening (4) bolts securing motor. Shift motor and refasten. For blower wheel adjustments, loosen set screw (not shown), shift wheel and refasten. 15. Apply latex caulk to seal between blower housing and top panel. 16. Reinstall electrical control box. 17. Place supply air plenum adaptor over discharge opening. Align holes in plenum adaptor, gasket and top panel. Secure with screws provided with adaptor.
PAGE 4
Plenum tee and elbow fittings may be installed at any point in the plenum duct run. If installing a fitting at the end of a full plenum section (see Figure 2.16), insert female end of fitting onto duct. If installing a fitting at a “cut” in the plenum duct (see Figure 2.16), form a field-fabricated flange (1-1/2" wide) in the duct and insert male end of fitting into duct. Tape the joint securely.