Gasketed Spiral Metal Duct System Installation Manual

ManualsBrandsSpacePak ManualsAccessoriesSpacePak round plenum 45 elbow

SECTION 1: INTRODUCTION ................................ 1

SmartSeal Metal Duct .......................................... 2

SECTION 2: INSTALLATION .................................. 2

Steps 1 and 2: ........................................................... 2

SECTION 3: ATTACHING AIR PLENUM

ADAPTOR (AL-SM9-PA) ........................................... 2

Step 4 Thru 7: ......................................................... 3

Step 8: Installing Air Distibution Components

(Plenum Duct and Plenum Take-Offs) .................... 3-4

IN UNITED STATES: 260 NORTH ELM ST. WESTFIELD, MA 01085 800-465-8558/FAX (413) 564-5815

IN CANADA: 7555 TRANMERE DRIVE, MISSISSAUGA, ONTARIO, L5S 1L4 (905) 672-2991/FAX (905) 672-2883

GASKETED

SPIRAL

METAL DUCT

INSTALLATION

MANUAL

SMSG2-311

W30-WG0193-01

3/11

SECTION 1: INTRODUCTION

The following terms are used throughout this

manual to bring attention to the presence of potential

hazards or to important information concerning the

product:

NOTICE: Used to notify of special instructions on

installation, operation or maintenance which are

important to equipment but not related to personal

injury hazards.

Summary of content (4 pages)

PAGE 1
SMSG2-311 W30-WG0193-01 GASKETED SPIRAL METAL DUCT INSTALLATION MANUAL SECTION 1: INTRODUCTION ................................ SmartSeal Metal Duct .......................................... SECTION 2: INSTALLATION .................................. Steps 1 and 2: ........................................................... SECTION 3: ATTACHING AIR PLENUM ADAPTOR (AL-SM9-PA) ........................................... 1 2 2 2 Step 4 Thru 7: .........................................................
PAGE 2
90° Plenum Elbow AC-SM9-EL90 Plenum End Cap AC-SM9-EC Plenum Tee AC-SM9-T Coupling AC-SM9-C Supply Tubing AC-ST6-100 Kwik Connect Wall Elbow AC-KCWE Plenum Duct (6FT Length) AC-SM9-6 Plenum Adaptor AC-SM9-PA Round Plenum Take-Off AC-TORD Kwik Connect BM-6818 Fan Coil Unit (See Legend) Sound Attenuating Tube BM-6926 Terminator Plate BM-6845 Return Air Duct 2 BM-6808-10 3 BM-6809-10 4 BM-6839-10 Winter Supply Air Shut-Off BM-6819 Balancing Orifice 27-6123 (15%) 27-6124 (35%) 27-6125 (50%) Secondary D
PAGE 3
8b. Shift motor mounting base (and blower housing) back toward coil to second set of mounting lugs on motor support channel. Rotate blower housing up 90°. Reattach base with screws. 9. Cut insulation from discharge air location on top panel (opening dimensions shown in Figure 2.3 of unit manual). Insert cut piece into opening. Apply adhesive per manufacturer's instructions. Attach cover plate to front of unit. 10. Bend both flanges 90° into cabinet using 3" duct-bill pliers.
PAGE 4
Cover plenum adaptor with extra insulation wrap included with straight plenum duct section. Insulation wrap is to be flush against the unit and secured with UL 181A tape. Reposition duct insulation and jacket to completely cover duct connection. Seal jacket seams with UL 181A tape. Plenum Take-off Installation Mark locations for take-offs on plenum duct. All take-off locations must be a minimum of 18" from any plenum tee, plenum elbow or the fan coil unit.