Contents Overview oon ne Setting Up ECG Monitoring. Display Detail io iii Monitoring Paced ECG Patients Restoring Default Settings: Changing ihe Display Rose) Selecting Options for Lead Display ECG Alarm Message Summary. 00 OYE Overview Digital telemetry EGG monitoring provides continuous monitoring of electrocardiographs signals in order fo detect abnormal cardiac rhythms, including e-threatening arrhythmia such as systole, ventricular Fibrillation.
A Ultra view Digital Telemetry oy b ” All Stony connections must ba ads by Space labs Medical personnel only. Leakage currants are not affected by the Sigh level output. The patient is: electrically isolated Fro the patient monitor by. the RE link: WARNING: * Operating television receivers or other CRT displays near he transmitter (within 2 fo 3 feet), or operation of some pacemaker programmers may suppress the ECG waveform, preventing QHS detection and tale counting.
ECG CA iw LOTION: Visually Inspect each lead wire for obvious damage and. replace them as needed. Only use patient cables and lead wires specified by Space labs Medical. Ether cables and lead wires may degrade performance and may damage the monitor during defibrillation. Non-Space labs Medical cables and lead wires may also change the required input impedance and DC offset voltage, affecting monitor performance. Do not use stainless steel electrodes.
a Ultraviolet Digital Telemetry Display Detail Signal detection is indicated pn your monitor when an ECG signal appears extinction the ECG parameter keybinding the zone assigned to receive the transmitted. telemetry channel. The: transmitters channel number Is always identified above the waveform, ta the left of the ECG key. I I oy CHAN 254% : v J: MON PACED.
a ts is ECG © Abnormal per minute cotter + ‘Current heart rate ECG lead designation for second lead ST segment level for second sadist” ECG key for-second lead coerces NIB measurements: systalic/diastolic (mean) at hours:minutes; Spas measurement at housemistresses (91343 only; shimmy not seen on continuous 8p0,}. Depending on the patient monitor's display size, the rite “NIB may not appear.
Ultra view Di digital Telemetry To restore default settings: Touch ECG: Touch SETUP; Touch RESTORE SETTINGS: Select YES. Bw Mesmer Ep GRIEVER To change the display resolution: 1: Touch ECG! 2: Touch SETUP. 3: Select MONITOR or EXTENDED: pacemaker rate during occurrences of cardiac arrest or some arrhythmia. Do not rely entirely upon ECG rate alarms. Keep pacemaker patients undo close surveillance. +The system may Insert pacemaker. flags into the ECG signal in response 10 signals that are not Pacemaker.
EE a: Ultra view Digital Telemetry HIE RATE ALARM Displayed during high rate alarms for dither 10 corridors or the duration of the alarm. UNLEARN Displayed when the software is in lair mode. CHANT 8 2 LEADS OFF Displayed when idea failures preside ECG majoritarianism both ECG channels 1 and 2. The message is displayed in the waveform zone for the first ECG channel: Ad alarm tone sounds if the molecule Has completed ita: initial period ot leaning ahd Fricasseeing has not bean suspends.
SpO, (91343 only) Contents Overview opus an Meting Up Spot Monitoring; Ensuring Accurate Monitoring Betting or Adjusting Alarm Limits ERE Setting Spot Data Averaging Period and Sampling Interval | Viewing Pulse Rate jun ha $pO2 with tantra-Aoric Balloon Pumps Using Spot with Neonates ©. Spot Alarm Message Summary. Spot Troubleshooting Guide: Overview Pulse optometry enables you to noninvasive monitor a patient's hemoglobin Oxygen saturation either.
A Ultra view Digital Telemetry To setup Sp0, monitoring: 1:2 Opening battery cover and Setting Up SpO, Monitoring The 81343 digital telemetry multilateral transitive uses Space labs Medical sensors as well as those from other manufacturers Refer io Accessories oh. page remove the battery: 1-13 for information concerning specific sensors. 2. Confirm that the DIP switches 1 through 8 are i the doomster CAUTION: setting (Switch 7 midi be sat ito * ‘Use only patient sensors specified by Space labs Radical.
Spot (91343 only) CHECK XX: HAN 2241 e ¥ KE YYY PACED: {ECB WAVEFORM ZONE © ALEX es 0 Spinoza 10:02 @ 180. BED NAME PATIENT NAME 78 his Figure 3-2: Display Zone ~ Elul Striven ° ° HR XXX AX LEAD cn ro ECG WAVEFORM ZONE: < Sportsman tos a R47:2 Jane Doe ° Figure 3-3: Display Zola == Split Serene © Current SOs value (percent) and episodic time of reading. (Time ia not displayed when using continuous mode of operation.
ul Interview Digital Telemetry To set or adjust Spo; alarms: Touch ECG. Touch ALARM LIMITS, Touch SPOT ALARM LIMITS. Select Sp ALARMS ON: Select His, LO= ALM DELAY, and MSG ALARM DELAY: Use row keys to adjust: Setting or Adjusting Alarm Limits Pulse optometry alarm limits ang delays are based either on Factory default limits or user-defined mas. The factory default settings for alarm limits are. 100% for high: and 85% for low.
i Spot (91343 only) MSG ALM DELAY Key This key sets the number of seconds the system will wait before it issues alarming Tone after any of the following messages: + SpO, UNAVAILABLE +. Bps FAULTY SENSOR * Sepoy SENSOR DISCONNECTED +1 8p0; SENSOR OFF PATIENT +: 8p05 INSUFFICIENT SIGNAL + SpO, AMBIENT LIGHT INCH. * SPO NOISY SIGNAL When this feature is OFF. the key label will read "MBG ALM DELAY. OFF" When 1s ON the able will read "MSG ALM DELAY xx“where “i” is the.
OS OT Ultra view Digital Telemetry Setting SpO, Data Averaging Period and Sampling interval oo biog fore set 8p0, data averaging is used to-smooth the optometry saturation value by transmitter DIP switches 1 averaging the patient input values over seconds. This selection is made. through 4 to correct by setting the DIP switches 1 and 2 beneath the battery compartment in the 91343 configuration digital telemetry parameterize transmitter. The default value 1s 8 seconds.
a To display heart rate from Spy Sensor: Taus ECG. Touch: SETUP. Touch RATE SOURCE: Select SPOT ON. Select Spot as rate source. A To Use with balloon pump: 15 Gel transmitter DIP switch 1a: ON: EEE To view the current setting of the IAMB DIP switch: 1: Touch ECG 2:5 Touch CHANNEL FORMAT, 3:5 Select SpO, ON: Spot (91343 only) No $p0» monitoring occurs between episodic sampling CAUTION: » b intervals.
000 Ultra view Digital Telemetry Using SpO, with Neonates Enabling neonatal operation, by setting transmitter DIP switch 7, changes. the. sensor detection operation in the transmitter, improving thee: signal quality for. neonatal patients: This switch must be set ON for neonatal use and set OFF for adult use: When the neonate operation is selected Thessaly status key in the Channel Format menu indicates NEO. SpO, Alarm Message Summary affect accurate monitoring values.
Sp (91343 only) Spas INSUFFICIENT SIGNAL Displayed: when: vi insufficient signal for proper-operation; «Poor sensor application or. site: Correctly re-apply of reposition toa more: perused site massage the site; or apply a new sensor: Bp, NOISY SIGNAL: Displayed when «Thi sensor signal is disturbed by motion or other interference. Eliminate sensor movement.
Clinical Situation Spot, Troubleshooting Guide Possible Cause Solution No Spot, abet is MW 5p0; is riot enabled at the 91343. [EE SpO, value displays 2277 EEL TG {intermittent or complete failure to operate Factors that cause significant va sensor accuracy MW Sp0, is not gabled at the 90478 receiver. WM: Be sure transmitter DIP switch 1 and 2 are set correctly. ME Be sire transmitter DIP switch 8 is QFE: MR Sensor not connected to patient. BW Adapter cable not connected to module properly.
os tai AAR tats NEE BEE Ee SpO, Troubleshooting Guide continue Clinical Situation Possible Cause Solution RISE BEET) MW £06 “Lads OFF condition exists. Ml Reattach ECO lead wires 1o patient and ESE WM Higher priority lath condition is resume ECG manning la clear present; pending ECG alarms: ME Cl oar current alarm condition and/or repatriation Spy alarms of interesting the: Module Configuration Manager. WM When SpO.