Model: 90300 Full Motion Wall Mount for Flat Panel TVs (Fits most TV sizes weighing up to 50 lbs) Questions, problems, missing parts? Before returning to the store, call STC Customer Service 9 a.m. - 5 p.m., Monday to Friday Toll Free 1-833-GOSTCNY (1-833-467-8269) STCNY.
Before you begin, carefully read and understand the instructions in this manual. Please follow the instructions in the order presented in this manual and observe all warnings and cautions. 16.85"(428mm) 3.15"(80mm) This mount has been tested to support televisions with maximum weight as follows: WOOD STUDS, BRICK,CONCRETE WALLS: 50lbs. (22.
D A B C E F G A Wall Mount 1 B Cable management 1 C VESA adapter 4 D E F G Screw Nut Allen key Wrench 4 4 1 1 NOTE: The hardware included is suitable for mounting to walls made of brick, solid concrete using (AA and BB).
To ensure proper mounting of the brackets to your TV, this mounting system includes several sizes (M4, M5, M6, and M8) of screws (DD). Select the screw diameter to use by inserting the various sized screws (M4, M5, M6, and M8) into the mounting holes in the back of your TV to identify the right size. CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV.
3 Arranging the wall plate Pull the arm out and then remove the VESA plate and the decorative cover to start assembling. G G Installing the VESA adapter VESA 300x300,400x400 VESA 400x200,300x200 15.74"(400mm) 11.81"(300mm) 7.87"(200mm) G E 11.81"(300mm) 15.74"(400mm) 15.74"(400mm) 11.81"(300mm) D VESA 400x300 G E D VESA 100x100,200x100,200x200 15.74"(400mm) 7.87"(200mm) 3.93"(100mm) D 7.87"(200mm) 3.93"(100mm) G E 11.
Attaching the mounting brackets to the TV CAUTION: Tighten the screws so the brackets are firmly attached. DO NOT OVERTIGHTEN. This may damage your TV. TVs ≤ 200 VESA EE CC DD TVs > 200 VESA Use of the spacers (FF) will vary depending on the type of TV you will be mounting.
5 PLANNING WALL PLACEMENT For Plasterboard/ Sheetrock walls mount directly on the board, no stud is required.
6 Installing the wall plate (concrete/brick wall) Use 1/4 in (6mm) drill bit to drill a pilot holes and then use a 3/8 in (10 mm) masonry drill bit to slowly drill 2.4 in (60 mm) holes. (6 mm) 1/4” 1 (10 mm) 3/8” 2 AA 3 4 8 BB (60 mm) 2.
7 Installing the wall plate (wood stud) Use a commercially-available stud finder to locate the stud centers in the wall. Studs are usually spaced 16 in. apart. Use a 3/16 in. (4.5 mm) drill bit to slowly drill 2.2 in. (55 mm) pilot holes.
9 Mounting the TV to the wall plate Secure the TV HEAVY! You will need assistance with this step.
Adjusting the TV to the desired position To adjust the tilting position, release the screws by using the Allen key, adjust the best tilting position and tight the screws to keep the position. F 12 To fold the mount into the decorative rear housing STEP 1: MOVE LEG 1 into the housing. STEP 2: POSITION LEG 2 at the approximate angle shown to avoid contact with the decorative plate. 1 2 STEP 3: MOVE LEG 2 and your TV backward and into the decorative rear housing.
Questions, problems, missing parts? Before returning to the store, call STC Customer Service 9 a.m. - 5 p.m., Monday to Friday Toll Free 1-833-GOSTCNY (1-833-467-8269) STCNY.