User's Manual

ManualsBrandsSouthco, ManualsElectronicsElectronic Swinghandle

H3-EM-69-100 Electronic Swinghandle

Operating Instructions

J-H3-EM-69-100-M_revB Page 1 of 4

Package Contents

H3-EM-69-x00 Electronic Swinghandle (qty1)

EM-0-45827 M3x25 POZIDRIV

Mounting Screws (qty 4)

EM-0-47151 M3x14 POZIDRIV

Mounting Screw (qty 1)

EM-0-45825 Rotation Limiter (qty 1)

E5-C-04 Pawl Screw (qty 1)

M3-0-24943-11 Lock Plug Screw (qty 1) (optional)

EM-0-45826 Top Mounting Bracket (qty 1)

EM-0-45822 Bottom Mounting Bracket (qty 1)

Operating Instructions (qty 1)

H3-EM-69-x00 Electronic Swinghandle

1. Handle

2. Prox Reader

3. Tri-Color Status LED

4. Lock Plug (optional)

Features

Installed 125kHz proximity reader module with RS232 data

output

Remote lock and unlock capability

Single or multi-point lock actuation

Momentary or continuous lock actuation

Tri-color LED (blue/magenta/red) to indicate lock and handle

status

DIN lock manual override

Accommodates both left and right doors

For indoor use only

WARNING: The H3-EM-69-000 is shipped without a lockplug. This

product must be paired with a Southco-approved lock to function properly.

Use with an unapproved lockplug voids the product warranty.

Contact Southco for additional support.

Specifications

Actuator Module

Supply Voltage (V

SUPPLY

): 12VDC to 24VDC (NOTE: Status LED will blink

red if the supply voltage is out of range.)

Standby Current: 50mA maximum at 12VDC

Operating Current: 200mA maximum at 12VDC (with no external

mechanical load applied to handle

Stall Current: 1A maximum (at 12VDC, limited to 2 seconds)

Operating Transit Time: 1 second maximum (NOTE: Power must be

present during transit times. If power is

removed while the lock slide is moving to the

unlock position, then the control input signal

must be asserted again. If power is removed

while the lock slide is moving to the lock

position, it will complete it’s cycle when power is

restored.)

Electronic Unlock Time: 3 seconds minimum

Open Collector Outputs: Rated for V

SUPPLY

, 100mA maximum load

Proximity Reader Module

Supply Voltage (V

): 12VDC to 24VDC

Operating Current: 50mA maximum (no external devices

attached)

Transmit Frequency: 125kHz FSK

TX Data Output Voltage: -12VDC / +12VDC

COM Port Settings:

parameter

setting

bits per second

9600

data bits

parity

none

stop bits

flow control

none

Mounting and Installation

Please refer to Southco trade drawing J-H3-EM-69-100 for mounting and

installation details.

NOTE: Use a #1 POZIDRIV

driver when installing the mounting

screws. See Southco trade drawing J-H3-EM-69-100 for additional details.

Summary of content (4 pages)

PAGE 1
H3-EM-69-100 Electronic Swinghandle Operating Instructions Package Contents H3-EM-69-x00 Electronic Swinghandle (qty1) EM-0-45827 M3x25 POZIDRIV® Mounting Screws (qty 4) EM-0-47151 M3x14 POZIDRIV® Mounting Screw (qty 1) EM-0-45825 Rotation Limiter (qty 1) E5-C-04 Pawl Screw (qty 1) M3-0-24943-11 Lock Plug Screw (qty 1) (optional) EM-0-45826 Top Mounting Bracket (qty 1) EM-0-45822 Bottom Mounting Bracket (qty 1) Operating Instructions (qty 1) H3-EM-69-x00 Electronic Swinghandle 2 3 1 4 WARNING: The H3-EM-6
PAGE 2
H3-EM-69-100 Electronic Swinghandle Operating Instructions Wiring Diagrams The proximity reader module of the swinghandle is accessed with a fourposition connector attached to a harness connected to the module’s circuit The H3-EM-69-x00 contains two separate functional modules: the actuator board. The module’s connector pinout is: module and proximity reader module. The actuator module controls and monitors the locking function of the swinghandle.
PAGE 3
H3-EM-69-100 Electronic Swinghandle Operating Instructions Proximity Module Data Output (TX) Status LED and Output Signals The proximity module will read a compatible card and output the ASCII code for the hexadecimal equivalent (not including parity bits). Refer to the Specifications section for the required RS232 COM port settings. The latch is equipped with a tri-color (blue/magenta/red) LED visible from the front of the latch. This LED provides a visible notification of the latch status.
PAGE 4
H3-EM-69-100 Electronic Swinghandle Operating Instructions Mechanically Released The latch is released by opening the handle or moving the cam from its lock position. The Status LED will flash blue. The electronic lock status output will be at its open collector state if the electronic lock slide is in the locked position. It will be 0V if the lock slide is in the unlocked position. The mechanical lock status output is 0V.