User's Manual

ManualsBrandsSouthco, ManualsElectronicsElectronic Swinghandle

H3-EM-68-100 Electronic Swinghandle

Operating Instructions

J-H3-EM-68-100-M_revA visit www.southco.com for latest version of this document Page 1 of 4

Package Contents

 H3-EM-68-x00 Electronic Swinghandle

with Proximity Reader (qty1)

 EM-0-45827 M3x25 Long Mounting Screws (qty 4)

 EM-0-47151 M3x14 Long Mounting Screw (qty 1)

 EM-0-45825 Rotation Limiter (qty 1)

 E5-C-04 Pawl Screw (qty 1)

 EM-0-45826 Top Mounting Bracket (qty 1)

 EM-0-45822 Bottom Mounting Bracket (qty 1)

 Operating Instructions (qty 1)

H3-EM-68-x00 Electronic Swinghandle with Proximity Reader

1. Handle

2. Prox Reader

3. Tri-Color Status LED

4. Lock Plug

Features

 Installed 125kHz proximity reader module with Wiegand data

output

 Remote lock and unlock capability

 Single or multi-point lock actuation

 Momentary or continuous lock actuation

 Tri-color LED (blue/magenta/red) to indicate lock and handle

status

 High security DIN lock manual override

 Accommodates both left and right doors

 For indoor use only

Specifications

Actuator Module

Supply Voltage (V

SUPPLY

): 12VDC to 24VDC (NOTE: Status LED will blink

red if the supply voltage is out of range.)

Standby Current: 50mA maximum at 12VDC

Operating Current: 200mA maximum at 12VDC (with no external

mechanical load applied to handle

Stall Current: 1A maximum (at 12VDC, limited to 2 seconds)

Operating Transit Time: 1 second maximum (NOTE: Power must be

present during transit times. If power is

removed while the lock slide is moving to the

unlock position, then the control input signal

must be asserted again. If power is removed

while the lock slide is moving to the lock

position, it will complete it’s cycle when power is

restored.)

Electronic Unlock Time: 3 seconds minimum

Open Collector Outputs: Rated for V

SUPPLY

, 200mA maximum load

Proximity Reader Module

Supply Voltage (V

): 12VDC to 24VDC

Operating Current: 20mA maximum (no external devices

attached)

Transmit Frequency: 125kHz FSK

DATA Signal Voltage: 5VDC

DATA Pulse Interval Time:40µs

DATA Signal Delay: 2ms

Mounting and Installation

Please refer to Southco trade drawing J-H3-EM-68-100 for mounting and

installation details.

Wiring Diagrams

The H3-EM-68-x00 contains two separate functional modules: the actuator

module and proximity reader module. The actuator module controls and

monitors the locking function of the swinghandle. The proximity module

reads the contents of a compatible proximity card and converts it to

Wiegand format.

These two modules operate independently of each other and require

connection to an access control unit (not provided), as illustrated below,

for the entire product to be fully functional.

Summary of content (4 pages)

PAGE 1
H3-EM-68-100 Electronic Swinghandle Operating Instructions Package Contents         Operating Transit Time: H3-EM-68-x00 Electronic Swinghandle with Proximity Reader (qty1) EM-0-45827 M3x25 Long Mounting Screws (qty 4) EM-0-47151 M3x14 Long Mounting Screw (qty 1) EM-0-45825 Rotation Limiter (qty 1) E5-C-04 Pawl Screw (qty 1) EM-0-45826 Top Mounting Bracket (qty 1) EM-0-45822 Bottom Mounting Bracket (qty 1) Operating Instructions (qty 1) Electronic Unlock Time: Open Collector Outputs: 1 second ma
PAGE 2
H3-EM-68-100 Electronic Swinghandle Operating Instructions The actuator module of the swinghandle is accessed with a six-position connector on the rear of the unit, shown below. Control Input Signal This signal is used to control the electronic lock slide position.   for UNLOCKED position: Supply 9VDC minimum (do not exceed supply voltage) for at least 50 milliseconds. The lock will remain unlocked for as long as the signal is present, or a minimum of 3 seconds.
PAGE 3
H3-EM-68-100 Electronic Swinghandle Operating Instructions Electronically Released Handle not Fully Closed The electronic lock slide is in the unlocked position and the handle can be pulled open.  The Status LED will alternate flashing blue/magenta.  The electronic lock status output is 0V while the lock slide is in the unlocked position.  The mechanical lock status output is at its open collector state.
PAGE 4
H3-EM-68-100 Electronic Swinghandle Operating Instructions FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.