User's Manual

ManualsBrandsSouthco, ManualsElectronicsElectronic Swinghandle

H3-EM-66-100 Electronic Swinghandle

Operating Instructions

J-H3-EM-66-100-M_revB visit www.southco.com for latest version of this document Page 1 of 4

Package Contents

 H3-EM-66-x00 Electronic Swinghandle

with RFID Reader (qty1)

 EM-0-45827 M3x25 POZIDRIV

Mounting Screws (qty 4)

 EM-0-47151 M3x14 POZIDRIV

Mounting Screw (qty 1)

 EM-0-45825 Rotation Limiter (qty 1)

 E5-C-04 Pawl Screw (qty 1)

 M3-0-24943-11 Lock Plug Screw (qty 1) (optional)

 EM-0-45826 Top Mounting Bracket (qty 1)

 EM-0-45822 Bottom Mounting Bracket (qty 1)

 Operating Instructions (qty 1)

H3-EM-66-x00 Electronic Swinghandle with RFID Reader

1. Handle

2. RFID Reader

3. Tri-Color Status LED

4. Lock Plug (optional)

Features

 Installed 13.56MHz RFID reader module with Wiegand data

output

 Compatible with 13.56Mhz RFID cards with 4, 7, or 8byte Unique

Identifiers (UID)

 Remote lock and unlock capability

 Single or multi-point lock actuation

 Momentary or continuous lock actuation

 Tri-color LED (blue/magenta/red) to indicate lock and handle

status

 DIN lock manual override

 Accommodates both left and right doors

 For indoor use only

WARNING: The H3-EM-66-000 is shipped without a lockplug. This

product must be paired with a Southco-approved lock to function properly.

Use with an unapproved lockplug voids the product warranty.

Contact Southco for additional support.

Specifications

Actuator Module

Supply Voltage (V

SUPPLY

): 12VDC to 24VDC (NOTE: Status LED will blink

red if the supply voltage is out of range.)

Standby Current: 50mA maximum at 12VDC

Operating Current: 200mA maximum at 12VDC (with no external

mechanical load applied to handle

Stall Current: 1A maximum (at 12VDC, limited to 2 seconds)

Operating Transit Time: 1 second maximum (NOTE: Power must be

present during transit times. If power is

removed while the lock slide is in transit, it will

complete it’s cycle when power is

restored.)

Electronic Unlock Time: 3 seconds minimum

Open Collector Outputs: Rated for V

SUPPLY

, 100mA maximum load

RFID Reader Module

Supply Voltage (V

): 12VDC to 24VDC

Operating Current: 60mA maximum (no external devices

attached)

Transmit Frequency: 13.56MHz

DATA Signal Voltage: 5VDC

DATA Pulse Interval Time: 40µs

DATA Signal Delay: 2ms

Output Format: Reverse Byte Order with Upper and Lower

Parity Bits

Mounting and Installation

Please refer to Southco trade drawing J-H3-EM-66-100 for mounting and

installation details.

NOTE: Use a #1 POZIDRIV

driver when installing the mounting

screws. See Southco trade drawing J-H3-EM-66-100 for additional details.

Wiring Diagrams

The H3-EM-66-x00 contains two separate functional modules: the actuator

module and RFID reader module. The actuator module controls and

monitors the locking function of the swinghandle. The RFID module reads

the contents of a compatible RFID card and converts it to Wiegand format.

These two modules operate independently of each other and require

connection to an access control unit (not provided), as illustrated below,

for the entire product to be fully functional.

Summary of content (4 pages)

PAGE 1
H3-EM-66-100 Electronic Swinghandle Operating Instructions Package Contents          Specifications H3-EM-66-x00 Electronic Swinghandle with RFID Reader (qty1) EM-0-45827 M3x25 POZIDRIV® Mounting Screws (qty 4) EM-0-47151 M3x14 POZIDRIV® Mounting Screw (qty 1) EM-0-45825 Rotation Limiter (qty 1) E5-C-04 Pawl Screw (qty 1) M3-0-24943-11 Lock Plug Screw (qty 1) (optional) EM-0-45826 Top Mounting Bracket (qty 1) EM-0-45822 Bottom Mounting Bracket (qty 1) Operating Instructions (qty 1) H3-EM-66-x00
PAGE 2
H3-EM-66-100 Electronic Swinghandle Operating Instructions The actuator module of the swinghandle is accessed with a six-position connector on the rear of the unit, shown below. NOTE: The mating connectors/harnesses are not provided with the H3-EM-66-x00. Refer to Southco trade drawing J-H3-EM-66-100 for mating connector/harness requirements.
PAGE 3
H3-EM-66-100 Electronic Swinghandle Operating Instructions Status LED and Output Signals Mechanically Released The latch is equipped with a tri-color (blue/magenta/red) LED visible from the front of the latch. This LED provides a visible notification of the latch status. The different latch states are described below. Please refer to the Control Input Signal, Electronic Lock Status Output Signal, and Mechanical Lock Status Output Signal sections for further details on these signals.
PAGE 4
H3-EM-66-100 Electronic Swinghandle Operating Instructions Electronic Lock Slide Error Error Input Command Sequence The electronic lock slide does not respond to the command input signal.  The Status LED will flash magenta if the latch is secured. It will alternate flashing red/magenta if the latch is mechanically released.  The electronic lock status output is at its open collector state.  The mechanical lock status output will be at its open collector state if the cam is in its lock position.