Other External Components Other External Components Ñ Camera Setup View Camera 1 Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. hh SETUP Menu screen appears. 3 Touch [Camera]. [ NOTE • To connect a camera, see . • To use a rear view camera, a REVERSE lead connection is required. • The rear view screen is displayed when you shift the gear to the reverse (R) position. ] Ñ Display the camera screen 1 Press the [MENU] button. hh MENU screen appears. 2 Touch ].
Other External Components To adjust the parking guidelines NOTE • Install the rear view camera in the appropriate position according to the instructions supplied with the rear view camera. 1 Connect an external component to the AV-IN input terminal. • When adjusting the parking guidelines, make sure to use the parking brake to prevent the car from moving. 2 3 Select [AV-IN] as the source. 1 Touch [ON] of [Parking Guidelines] in the Camera screen. 2 Touch [Guidelines SETUP] in the Camera screen.
Setting Up Setting Up Monitor Screen Setup You can adjust image quality in video screen. 1 Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. ] System Setup NOTE • Each operation in this section can be started from the multi function menu. [ 1 Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. hh Screen Control screen appears. 3 Adjust each item as follows. ■ Contrast / Brightness / Colour / Tint Adjusts each item.
Setting Up User Interface Setup Special Setup You can setup user interface parameters. You can setup Special parameters. 1 Press the [MENU] button. hh MENU screen appears. 1 Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. hh SETUP screen appears. 2 Touch [ ]. hh SETUP screen appears. 3 Touch [User Interface]. [ ] 3 Touch [Special]. hh Special screen appears. 4 Set each item as follows. ■ DEMO Set the demonstration mode. Default is “ON”.
Setting Up Display Setup Ñ Change background image or 1 Press the [MENU] button. hh MENU screen appears. 2 1 2 Touch [ ]. hh SETUP screen appears. 3 Touch Display . [ color Touch [Background] in the Display screen. Select an image. ] hh Display screen appears. 4 Set each item as follows. ■ Dimmer Select dimmer mode. OFF: The display and buttons do not dim. ON: The display and buttons dim.
Setting Up To register original image You can load an image from the connected USB device and set it for the background image. Before operating this procedure, it is necessary to connect the device which has the image to load. AV Setup You can set AV parameters. 1 Press the [MENU] button. hh MENU screen appears. 1 Touch [User1 Select] or [User2 Select] in the Background screen. 2 Touch [ ]. hh SETUP screen appears. 2 Select the image to load. 3 Touch [AV]. hh AV screen appears.
Controlling Audio Controlling Audio Speaker/ X’over setup NOTICE • Each operation in this section can be started from the multi function menu. 1 Press the [MENU] button. hh MENU screen appears. You can adjust the various settings such as audio balance or subwoofer level. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Speaker/Xʼover]. 4 Select a car type. You can setup the car type and speaker network, etc.
Controlling Audio ■ Tweeter (Only for Front) You can set the tweeter when you are selecting front speakers. None, Small, Medium, Large ■ TW (Tweeter) Gain *2 Adjusts the tweeter level. (When front is selected on Speaker Select screen) ■ Phase Inversion*3 Sets the phase of subwoofer output. Check [Phase Inversion] to shift the phase 180 degrees. (When subwoofer is selected on Speaker Select screen) ■ X’over Displays the speaker crossover setup screen.
Controlling Audio Equalizer Control ■ SW Level Adjusts the subwoofer volume. This setting is not available when subwoofer is set to “None”. See Speaker/ X’over setup (P.41). You can adjust equalizer by selecting the optimized setting for each category. 1 Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Equalizer]. 4 Touch the screen and set the Graphic Equalizer as desired. Ñ Recall the EQ curve 1 2 Touch [Preset Select]. Select EQ curve.
Controlling Audio Volume Offset Finely adjust the volume of the current source to minimize the difference in volume between different sources. You can set sound effects. 1 Press the [MENU] button. hh MENU screen appears. Press the [MENU] button. hh MENU screen appears. 2 2 Touch [ ]. hh Audio screen appears. Touch [ ]. hh Audio screen appears. 3 Touch [Sound Effect]. 3 Touch [Volume Offset]. 4 Set each item as follows. 1 4 Touch [+] or [−] to adjust the level.
Controlling Audio Listening Position/ DTA Adjust the sound delay time as nearer speakers to the selected seat have more delay time, so that the sound from each speaker arrive a listener at the same time. 1 Press the [MENU] button. hh MENU screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Position/DTA]. 4 Select listening position from [Front R] (Right front), [Front L] (Left front), [Front All] (All front), and [All]. Position DTA control You can fine-adjust your listening position.
Remote control Remote control This unit can be operated using the remote control KNA-RCDV331 (optional accessory). Functions of the Remote control Buttons • Aim the remote control directly at the remote sensor on the faceplate. • DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting). 1 2 3 5 4 6 7 1 SRC 2 L Switches to the source to be played. Plays or pauses. 3 Û When a call comes in, answers the call. 4 VOL R S Adjusts the volume.
Connection/Installation Connection/Installation Before Installation Before installation of this unit, please note the following precautions. # WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation Ñ Supplied accessories for Installing the unit installation 1 (3 m) x1 2 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. x2 3 x1 4 Ñ Trim plate 1) Attach accessory 2 to the unit. (2 m) x1 5 x1 Ñ Installation procedure 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Make the proper input and output wire connections for each unit.
Connection/Installation Ñ Removing the unit NOTE 1) Remove the trim plate by referring to step 1 in “Removing the trim plate”. 2) Insert the extraction key (accessory 2) deeply into the slot as shown. (The protrusion at the tip of the extraction key must face toward the unit.) • Swap the clips if necessary. 2 Ñ Removing the trim plate 1) Use the extraction key (accessory 5) to lever out the four tabs (two on the left part, two on the right part).
Connection/Installation Ñ Connecting wires to terminals STEERING WHEEL REMOTE INPUT Light Blue/Yellow (Steering remote control wire) To steering remote To use the steering wheel remote control feature, you need an exclusive remote adapter (not supplied) matched to your car. Light Green (Parking sensor wire) Accessory 3: Parking Extention cable Connect to the vehicle’s parking brake detection switch harness. PRK SW USB terminal[1] (1 m) For best safety, be sure to connect the parking sensor. 5V=1.
Connection/Installation Ñ ISO Connector function guide Pin A-4 A-5 A-6 A-7 A-8 Color and function Yellow Battery Blue/White[1] Power Control Orange/White Illumination Red Ignition (ACC) Black Earth (Ground) Connection B-1/ B-2 Purple (+) / Rear Right Purple/Black (–) B-3/ B-4 Gray (+) / Front Right Gray/Black (–) B-5/ B-6 White (+) / Front Left White/Black (–) B-7/ B-8 Green (+) / Rear Left Green/Black (–) [1] Max.
Troubleshooting Troubleshooting Problems and Solutions If any trouble occurs, first check the following table for possible problems. NOTE • Some functions of this unit may be disabled by some settings made on this unit. • What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Ñ About settings • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter.
Appendix Appendix Playable Media and Files You can play various kinds of media and files on this unit. Ñ About files The following audio and video files are supported. ■ Playable Audio files Format AAC-LC (.m4a) MPEG2/4 AAC LC HE-AAC(V1,V2) MP3 (.mp3) MPEG 1/2 Audio Layer 3 WMA (.wma) Windows Media Audio Standard L3 profile (Version 7,8,9) Linear PCM RIFF waveform Audio (WAVE) (.wav) Format FLAC (.flac) flac Vorbis (.
Appendix Specifications ■ Monitor section Picture Size : 6.75 inches (diagonal) wide : 151.8 mm (W) × 79.7 mm (H) Display System : TN LCD panel Drive System : TFT active matrix system Number of Pixels : 1,152,000 (800H x 480V x RGB) Effective Pixels : 99.99 % Pixel Arrangement : RGB striped arrangement Back Lighting : LED ■ USB interface section USB Standard : USB 2.0 High Speed File System : FAT 16/ 32, NTFS Maximum Power Supply Current : DC 5 V 1.
Appendix ■ FM tuner section ■ Audio section Frequency Range (step) : 87.5 MHz – 108.0 MHz (50 kHz) Maximum Power Output (Front & Rear) : 50 W × 4 Usable Sensitivity (S/N : 26 dB) : 13.2 dBf (1.3 μV/75 Ω) Full Bandwidth Power (at less than 1% THD) : 21 W × 4 Quieting Sensitivity (S/N : 46 dB) : 19.2 dBf (2.5 μV/75 Ω) Output frequency band : 20 – 20,000 Hz Frequency Response : 30 Hz – 15 kHz Preout Level (V) : 4 V/ 10 kΩ S/N Ratio (dB) : 70 dB (MONO) Preout Impedance : 1.
Appendix About this Unit ■ Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. • This product is protected by certain intellectual property rights of Microsoft.
Appendix – Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. – Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
Appendix Declaration of Conformity with regard to the RE Directive 2014/53/EU Declaration of Conformity with regard to the RoHS Directive 2011/65/EU Manufacturer: JVCKENWOOD Corporation 2 9 6 7 -3, Ishikawa-machi, Hachioji-shi,Tokyo 19 2 - 8 52 5, J apan EU Representative: JVCKENWOOD Europe B.V. Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands English Hereby, JVCKENWOOD declares that the radio equipment DMX5020DABS/ DMX5020BTS / DMX4707S is in compliance with Directive 2014/53/EU.
Українська Таким чином, компанія JVCKENWOOD заявляє, що радіообладнання DMX5020DABS/ DMX5020BTS/ DMX4707S відповідає Директиві 2014/53/EU. Повний текст декларації про відповідність ЄС можна знайти в Інтернеті за такою адресою: Türkçe Burada, JVCKENWOOD DMX5020DABS/ DMX5020BTS/ DMX4707S radyo ekipmanının 2014/53/AB Direktifine uygun olduğunu bildirir. AB uyumluluk deklarasyonunun tam metni aşağıdaki internet adresinde mevcuttur.
URL : http://www.kenwood.