MA100 Owner’s Manual
MA100 CONTENTS Introduction................................................................................................................................................................................. 1 Features .............................................................................................................................................................................. 1 Box Content ..........................................................................................................
MA100 INTRODUCTION Thank for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen receiver for maximum enjoyment.
MA100 Safety Information To ensure full satisfaction with the product, please read the entire instruction manual. Keep instructions for future reference. Follow all operation guidelines and adhere to all safety warnings and cautions to ensure safe use. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Only use attachments/accessories specified by the manufacturer. Never use harsh cleaning agents.
MA100 INSTALLATION Mounting the Radio 1. 2. Choose a mounting location on the dash board or instrument panel that will allow room behind to run radio cables to the power source. Consider how you will use the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables to an accessible area. Cut a hole in the dash board using the template provided in the back of this manual. At least 3 ¾” depth is needed to mount the radio.
MA100 Auxiliary Input Connect a portable audio device to the Audio Input (AUX IN RIGHT/LEFT) on the back of the unit using RCA cables. Line Output The Line Out connectors (LINE OUT RIGHT/LEFT) on the back of the unit output a line-level analog signal.
MA100 Wiring Diagram PIN NO. WIRE COLOR DESCRIPTION B1 PURPLE RIGHT REAR SPEAKER (+) B2 PURPLE/BLACK RIGHT REAR SPEAKER () B7 GREEN LEFT REAR SPEAKER (+) B8 GREEN/BLACK LEFT REAR SPEAKER (-) A3 BLUE POWER AMP REMOTE A8 BLACK GROUND A7 RED ACC +12V B3 GRAY RIGHT FRONT SPEAKER (+) B4 GRAY/BLACK RIGHT FRONT SPEAKER () B5 WHITE LEFT FRONT SPEAKER (+) B6 WHITE/BLACK LEFT FRONT SPEAKER () 5 Note: Do not connect the red wire to a constant power connection.
MA100 OPERATION Basic Functions Power Press the JENSEN power button (1) to turn the unit on/off. Restore Factory Settings Perform the following steps to reset the radio to factory default settings: 1. Press and hold the power button (1) to display the software version. 2. Press the VOL + button (3) to display “RESET”. 3. Press the power button to confirm factory default restore. After reset, the unit will default to FM mode. Volume Press the VOL + button (3) to increase the volume.
MA100 3. 4. With the display showing the current tuning mode, press the VOL - or VOL+ button (2, 3) to change between USA/EURO. Press the JENSEN power button (1) to confirm your selection. Frequency Tuning Press the l<< or >>l button (6, 7) to fine tune the radio frequency. Channel Seek Press and hold the l<< or >>l button to seek strong radio frequencies. Preset Channel Store To manually store a favorite channel to one of the six preset channels, perform the following steps: 1.
MA100 Bluetooth Operation The MA100 includes built-in Bluetooth technology that allows you to connect this head unit to Bluetooth-enabled devices for streaming audio playback. About Bluetooth Technology Bluetooth wireless technology is a short-range wireless radio protocol. Operating in the 2.4 GHz range, it transmits audio and data at speeds up to 2.1 Mbit/s over a range of up to 10 meters.
MA100 Pairing a Bluetooth Device Before you begin, consult the owner’s manual for the Bluetooth device you want to pair with the MA100. 1. Make sure the device is on and ready to receive a signal from the MA100. With the MA100 in Bluetooth Audio mode, press and hold the MODE (8) button. 2. Repeatedly press MODE until the unit displays PAIR ON, then press ||/MUTE. The unit will display PAIR and count down from 120 to 0.
MA100 APP OPERATION JENSEN® Specialty Controller is the ultimate wireless remote control for your JENSEN stereo system.
MA100 TROUBLESHOOTING Table 1: Troubleshooting Problem No power Solution If the power supply is connected to the vehicle accessory circuits but the engine is not on, switch the ignition key to “ACC” Fuse may be blown. Replace with 10AMP ATO fuse. No AM/FM Reception Antenna cable not connected; insert antenna cable firmly. No sound Check volume level; increase volume if necessary. Check power; make sure device is on. Check device; press the play/pause button to ensure unit is not in Pause mode.
MA100 SPECIFICATIONS General Power Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 12 Volts, Negative Ground Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-16VDC Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASA Electronics Corporation www.asaelectronics.com www.jensenheavyduty.com ©2015 ASA Electronics Corporation v.