Operating Instructions

Condenser Microphone
Microphone à condensateur
Operating Instructions Mode d’emploi
C-80
5-042-796-11(1)
©2022 Sony Corporation
Printed in Japan
Imprimé au Japon
https://www.sony.net/







English Condenser Microphone
Before using the microphone, please read this manual thoroughly. This manual should be
retained for future reference.
FOR UNITED STATES CUSTOMERS. NOT APPLICABLE IN CANADA, INCLUDING IN THE
PROVINCE OF QUEBEC.
POUR LES CONSOMMATEURS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y
COMPRIS LA PROVINCE DE QUÉBEC.
Owner’s Record
The model and serial numbers are located on the product.
Record them in the space below and store safely.
Model No.
Serial No.
Names and Functions of Parts (Fig.)
(The numbers refer to the corresponding numbers in the figure.)
Microphone

PAD switch
Select the PAD switch to the level of input source.
: Off
: On
 LOW CUT switch
The low cut filter reduces the wind noise effectively.
: Normal setting
: The low cut filter is applied.

Output connector (XLR-3-12C type)
The sound recorded with the microphone is output. The power is supplied to the
microphone from an external equipment through this connector when the microphone
is operating on the external power supply.

Cradle suspension
When using a microphone stand (not supplied), for example, attach the cradle
suspension to the microphone.

Ring
Be sure to rotate and fix the ring after the microphone is equipped to the cradle
suspension. Unless done so, there is a risk the microphone will fall.
Power Supply
This microphone is powered only from an external power supply. Connect output connector
 of the microphone to the microphone connector of a Phantom power supply (external
power supply) or an audio mixer. For connection, use a microphone cable.
Note
An unbalanced cable cannot be connected to this microphone. Be sure to use a balanced
microphone cable.
Precautions
• Unless the unit is used correctly, water may get into the unit and cause fire, electrocution,
or malfunctions. Note the following cautions carefully and use the unit correctly.
Other notes
• Microphones are delicate. Do not drop or subject it to excessive shock.
• Avoid extended usage or storage in high humidity or temperatures above 60 °C (140 °F).
It may cause noise or failure.
• If acoustic feedback occurs during use (a howling sound is heard from the speakers),
point the microphone away from the speakers or increase the distance between the
microphone and the speakers.
• The microphone output signal is a balanced output. Unbalanced output is not supported,
so be sure to connect it to the balanced input circuit.
• Since the microphone adopts an extremely high impedance circuit, if the switch is
changed while the external power is on, it may emit induction noise, but this is not a
malfunction.
• A cable with the connector housing part connected to the ground wire (pin 1) is
recommended for the microphone cable. Cables that are not connected to a ground wire
may emit noise. If a ground terminal is available, noise can be reduced by connecting to
that terminal. Also, if used extending several microphone cables and the connector
housing part touches the floor, noise may worsen.
Note
Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE
FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE
TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION
OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.
Specifications
Type Condenser Microphone
Power supply External power supply operation 44 V to 52 V DC (IEC* 61938 P48)
Current consumption Less than 4.5 mA
Output connector XLR-3-12C Type
Dimensions Approx. 40 mm (1.57 in.) dia. × 158 mm (6.22 in.)
Mass Approx. 215 g (7.6 oz)
Included items Condenser Microphone (1)
Cradle suspension (1)
Carrying case (1)
Frequency response 20 Hz - 20 000 Hz
Directivity Uni directional
Output impedance 90 Ω ±15%, balanced
Sensitivity -30 dB (Uni directional)
(deviation ±3 dB)
(0 dB=1 V/Pa, 1 kHz)
Inherent noise Less than 12.5 dB SPL (Uni directional)
(0 dB=2 × 10
-5
Pa)
(IEC* 61672-1 A-Weighted, 1 kHz, 1 Pa)
Maximum input sound pressure level
More than 138 dB SPL (Uni directional)
(output level for 1% waveform distortion at 1 kHz, converted into
equivalent input sound pressure level: 0 dB=2 × 10
-5
Pa)
Dynamic range More than 125.5 dB (Uni directional)
PAD 0 dB / -10 dB (switchable)
LOW CUT filter Flat / 70 Hz (switchable)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Frequency response and polar patterns/curve
(Fig.)