xx INSTRUCTION MANUAL xxxxxx
Introduction Thank you for your purchase of "xxxxxx". For proper use of the xxxxxx, read this manual carefully before and while you use the xxxxxx. About manuals ● " クイックスタートガイド (Quick Start Guide)" (Supplied accessories) Part names and functions are explained. ● "Instruction Manual" application (Application of the terminal) (in Japanese only) Operations and settings of each function are explained. You can search by free word, open a setting screen or launch an application from a displayed page, etc.
❖Information ・ ・ ・ ・ ・ ・ ・ ・ ・ Please note that "xxxxxx" is called as "the terminal" in this manual. In this manual, the description is written based on the default state. In this manual, the easier procedure is described for the functions and settings which have multiple operating procedures. The terminal may have a software update of the operating system (OS) for the purpose of quality improvement or addition of functions. In that case, operation procedure may change.
Contents ■ Supplied accessories. . . . . . . . . . . . . . . . . 1 Precautions . . . . . . . . . . . . . . . . . . 4 About using the terminal....................................................4 Recommended features......................................................7 Safety Precautions (Always follow these directions).....................................................................................8 Handling precautions.........................................................
dmarket.................................................................................... 148 Play Store................................................................................. 149 Osaifu-Keitai........................................................................... 150 TV.................................................................................................. 154 Music.......................................................................................... 161 Location services.....
Precautions About using the terminal The terminal supports 5G, LTE, W-CDMA, GSM/GPRS and wireless LAN systems. ・ Because the terminal uses radio frequencies, it is not available inside a tunnel, underground, building or other locations where radio waves do not reach, in a place with weak radio waves, or out of 5G service area or LTE service area. Also, it may not be available on the upper floors of high-rise apartments or buildings, even if there are no obstructions around you.
The terminal automatically performs communication for synchronizing data, checking the latest software version, and maintaining a connection with the server, and for other purposes. If you transmit a large amount of data, such as when downloading applications or watching video, a packet communication charge becomes high. Subscription to Packet Pack/packet flat-rate service is highly recommended.
The screen may become partially dark or the colors may be changed if you set the display brightness to brighter than necessary or use the terminal extremely for a long time. Also, unevenness of colors or brightness, or changes of colors may be found depending on direction you are looking. That is because of the structure of organic EL display, not a malfunction. ・ DOCOMO is not liable to any failures or malfunctions for commercially available optional equipment.
Recommended features Cinematography Pro (Cinema Pro) "Cinema Pro" feature, supervised by Sony professional camera team, is specialized for shooting videos. You can enjoy the operational feeling like shooting with a professional cinema camera, and its imaging. Record of casual daily scenes can be in cinematic impression. → P.145 Multi-window When you want to "post to SNS while seeing a video" or "search for the Internet when writing email", the Multi-window feature is very useful.
Safety Precautions (Always follow these directions) For safe and proper use of the terminal, please read the "Safety Precautions" prior to use. ■ ALWAYS observe the safety precautions since they intend to prevent personal injury or property damage. ■ The following symbols indicate the different levels of injury or damage that may result if the guidelines are not observed and the terminal is used improperly.
1. Handling the terminal, adapter, wireless charger, docomo nano UIM card, and TV antenna cable (common) Don’t DANGER Don’t Don’t Don’t Do not use, store or leave the equipment in locations subject to high temperature or accumulation of heat (e.g. by the fire, near a heater, under a kotatsu or bedding, in direct sunlight, in a car in the hot sun). Doing so may cause fire, burns, injury, electric shock, etc.
No disassembly Do not disassemble or modify the equipment. Doing so may cause fire, burns, injury, electric shock, etc. WARNING Don’t No liquids No liquids Do Do not let the equipment get wet with liquids such as water (drinking water, sweat, seawater, urine of pet animals, etc.). Doing so may cause fire, burns, injury, electric shock, etc. For waterproofness, see the following. ⇒ P.
Do Do Do Do Power off the terminal near electronic devices or equipment operating on high precision control or weak signals. The radio wave from the terminal may interfere with the operation of electronic devices or equipment. * The following are some electronic devices or equipment that you should be careful of: Hearing aids, implantable cardiac pacemaker, implantable cardioverter defibrillator, other electronic medical equipment, and other automatically controlled devices or equipment.
Don’t Do Keep the equipment out of the reach of babies and infants. Especially be careful with a storage location for small parts such as the docomo nano UIM card/microSD card tray Doing so may cause accidental ingestion, injury, electric shock etc. Be careful when using the terminal continuously for a long time or while charging because the temperature of the terminal may rise.
Don’t Don’t Don’t Do Do Do not watch a repeatedly-blinking screen for a long time. Doing so may cause cramp, loss of consciousness, etc. Do Do not allow water or other liquids (drinking water, sweat, seawater, urine of pet animal, etc.), or foreign substance such as a metal parts (blade of cutter, staple, etc.) or flammables to get in the docomo nano UIM card/microSD card slot of the terminal. Do not insert the docomo nano UIM card or a microSD card into wrong slot, or insert it in wrong orientation.
Do If the substance of the internal battery leaks or gives off a strange smell, immediately remove it from the vicinity of open flames. The leaking liquid may ignite fire, catch fire, explode etc. Do Be careful not to allow a pet etc. to bite the terminal. Doing so may cause fire, burns, injury, etc. because of damage of the internal battery. Don’t When using the motion sensor, check the safety around you, hold the terminal firmly, and do not shake it unnecessarily.
Do Do Do Keep the equipment out of the reach of children, people who needs to be supervised, etc. The terminal (including the supplied accessories) contains magnets. If he or she swallows the magnet, it may cause suffocation, or serious symptom resulting from hurt of bowel etc. When he or she swallowed the magnet, consult a doctor immediately. Do not let it close to medical device.
Don’t Do not connect the voltage converter (e.g. travel converter for overseas) to AC adapter. Doing so may cause ignition, overheating, electric shock etc. Don’t Do not put an excessive force to the connection part with the adapter connected to the terminal. Doing so may cause fire, burns, injury, electric shock, etc. Don’t No wet hands Do Do not charge equipment when it is wet with liquid such as water (drinking water, sweat, seawater, urine of pet animals, etc.) with the wireless charger.
Do If the charging terminal is deformed such as being bent etc., stop using immediately. Do not use it with the deformation restored. Doing so may cause fire, burns, injury, etc. due to short-circuit of charging terminal. Unplug Always disconnect the power plug from a power outlet or accessory socket when not using it. Keeping with connected to the power plug may cause fire, burns, electric shock, etc.
Do Do When you get close to other people within 15 cm just like not having enough space to turn around, set the radio wave of the terminal to OFF beforehand (Airplane mode, to Power off, etc.). A person in close proximity may put on implanted a medical electrical equipment such as pacemakers and ICDs. The radio waves from the terminal may affect the performance of electronic medical equipment. Follow the instructions of each medical facility for the use of the terminal on their premises.
Part Tray of docomo nano UIM card/tray of microSD card ■ Material Surface treatment Polyacetal resin ― Handling precautions ■ Common precautions ・ TV Antenna cable SO02 Part Connecting plug (body), headset jack (body), cable Connecting plug (inside resin part), headset jack (inside resin part) Connecting plug (metal jack), headset jack (metal jack) Connecting plug (insulator) Material Surface treatment Thermoplastic ― elastomer resin (black) Polypropylene ― resin (black) Copper alloy xxxxxx is w
- Drops of water or dirt left on the display may cause stains. - Do not use alcohol, thinner, benzine, cleaning detergent, etc. to clean the terminal. These chemicals may erase the printing on the terminal or cause discoloration. ・ Clean the jacks or the fingerprint sensor occasionally and use the terminal in a clean state. If the jack etc. is dirt, you may not use the terminal normally. When cleaning, be careful not to damage the jack etc. ・ Make sure to use the terminal without excessive force.
It is not abnormal if the terminal becomes warm while in use and charging. You can continue using the terminal. ・ Do not expose the camera lens under direct sunlight. ・ If you do so, some of the elements may melt or become faded. ・ ・ The operations of the functions using the proximity sensor, charging with the wireless charger, etc. ,may not work properly. For a location of proximity, see the following. ⇒ P.
・ To store the terminal, avoid the following conditions so as not to degrade the performance or the battery life of the internal battery. - The battery is fully charged (immediately after the charging is complete) - The battery has run out (the terminal cannot power on) An appropriate battery level for storing is about 40%. ・ Type of internal battery for the terminal is as follows.
・ Do not get a contactless IC card such as traffic IC card close to the wireless charging pad or the terminal during wireless charging. ・ Doing so may cause data loss or malfunction. ・ Doing so may cause damage of the contactless IC card. ■ ・ If the IC is dirt, it may not be used properly. Clean the terminal with a dry soft cloth (such as used for cleaning eyeglasses). ・ Back up data that you saved to the docomo nano UIM card to a microSD card, a PC, or cloud, etc.
・ Frequency band The frequency band used by the terminal's Bluetooth/wireless LAN function is written as follows: 2.4 : This radio equipment uses the 2400 MHz band. FH/XX/DS/OF: Modulation scheme is the FH-SS, other system, DS-SS, or OFDM system. 4 : The estimated interference distance is 40 m or less. 8 : The estimated interference distance is 80 m or less. : The full band between 2400 MHz and 2483.5 MHz is used and the band of the mobile identification device can be avoided.
■ Wireless LAN (WLAN) precautions Wireless LAN (WLAN) exchanges information using radio waves, and allows you to freely establish LAN connection if you are within an area where radio waves reach. However, without appropriate security settings, communications may be intercepted or hacked by malicious parties. It is recommended to configure necessary security settings on your own judgment and responsibility.
・ 5GHz device cautions The terminal can use 3 frequency bands of 5.2GHz band (W52), 5.3GHz band (W53), 5.6 GHz band (W56). - 5.2GHz band (W52/36, 40, 44, 48 ch) - 5.3GHz band (W53/52, 56, 60, 64 ch) - 5.6GHz band (W56/100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 144 ch) Use of 5.2/5.3 GHz band wireless LAN outdoors is prohibited by the law (except when communicating with an access point of high power data communication system for 5.2 GHz band/relay station).
■ Note ・ Do not use a remodeled terminal. Using a remodeled terminal violates the Radio Law/Telecommunications Business Act. The terminal is compliant with rules on the technical standard conformance of specified wireless equipment based on the Radio Law/ Telecommunications Business Act, and as a proof of it, the "Technical Compliance Mark " is depicted on the electronic nameplate of the terminal.
Waterproofness/ Dustproofness xxxxxx provides waterproofness property of IPX5*1, IPX8*2, and dustproofness property of IP6X*3 with the cover of docomo nano UIM card/microSD card slot firmly attached. *1 IPX5 means that a communication device keeps functioning after applying a jet flow of 12.5 L/min. from every direction from a distance of approximately 3 m for at least 3 minutes using water nozzle in 6.3 mm inner diameter.
・ You can use the terminal in a bathroom. - Do not immerse the terminal into a bathtub. Also, do not use the terminal in hot water. Doing so may cause malfunction. If you should fall the terminal into the bathtub, immediately pick it up to drain water in specified procedure (P.32). - Never put the terminal in hot spring water or water containing soap, detergent or bath powder. In case the terminal gets wet with water other than tap water, wash it in the procedure above.
■ Opening the cover of docomo nano UIM card/microSD card slot Put your tip of finger (fingernail) into the groove and draw the cover out in the arrow direction. ■ Closing the cover of docomo nano UIM card/microSD card slot Push the tray all the way in the arrow direction and firmly press parts and make sure that there are no gaps between the terminal and the cover.
Do not perform actions shown in the illustrations below. Using Soap/Detergent/ Washing with brush/sponge Bath powder Soaking in ocean water Machinewashing Using in hot spring Do not move the terminal in water or slam the terminal against the surface of water. ・ If you put the terminal in tap water, be sure to have it within 30 minutes. ・ When you use the terminal in swimming pool, obey rules of the facility. ・ The terminal does not float on water. ・ Do not leave water on the terminal.
c DOCOMO does not guarantee actual operations under all states. Malfunctions deemed to be caused by inappropriate operation by the customer are not covered by the warranty. Draining water from the terminal When the terminal is wet, water may flow out after wiping it off; drain the water in the following steps. a Hold the terminal firmly and wipe off moisture on the terminal surface and back side with dry, clean cloth etc.
d Wipe off water drained from the terminal with dry, clean cloth etc., and dry naturally. ・ Wipe off water drained from the terminal with dry, clean cloth etc., and dry naturally. ・ Do not wipe off water remaining in gaps directly with a cotton swab etc. ・ Dry the terminal naturally for about 3 hours at room temperature. ・ Never connect a Type-C plug if the terminal is wet.
Before using the terminal Part names and functions a b c Second microphone : Used for reducing noise when calling. d Front camera lens → P.131 e Earpiece/speaker f Proximity/light sensor*1 : Detects a face approach during a call to prevent misoperation, or used for automatic control of the screen brightness. g Notification LED → P.68 h Display (Touch screen) → P.53 i Speaker j Mouthpiece/microphone k USB Type-C jack : Used for charging etc. It supports USB Power Delivery.
❖Note The back panel cannot be removed. Attempting to remove the back panel with excessive force may cause damage or a malfunction. ・ The battery is built into the terminal and not removal. ・ Flash/Photo light RGBC-IR sensor*1 : When shooting, it detects elements of light source of shooting environment to adjust white balance automatically. q 5G antenna section*2 r 5G/LTE/Wi-Fi/Bluetooth/GPS antenna section*2 s 5G/Wi-Fi antenna section*2 t Camera lens→P.131 u mark→P.
docomo nano UIM card The docomo nano UIM card is an IC card recorded user information such as your phone number etc. ・ You can use the terminal with a docomo nano UIM card. If you have a docomo mini UIM card, UIM, or FOMA card, bring it to a docomo Shop to replace it with a docomo nano UIM card. ・ When docomo nano UIM card is not inserted to the terminal, making calls, packet communication, etc. are not available.
3 Set the docomo nano UIM card in the tray with the IC face down. 5 Make sure that the corner cut of the card is oriented properly. ・ Be sure to fit the docomo nano UIM card into the tray so that it does not shift. ・ 4 Hold the terminal horizontally, insert the tray with the card into the terminal, and then push it straight. ・ Check the orientation of the terminal and the tray.
3 4 Remove the docomo nano UIM card from the tray. Hold the terminal horizontally, insert the tray into the terminal, and then push it straight. ・ 5 Check the orientation of the terminal and the tray. Firmly push the tray into the end and make sure that there are no gaps between the terminal and the cover (P.37). microSD card You can save the data in the terminal to a microSD card or import data from the microSD card to the terminal.
The terminal supports microSD cards of up to Class 10 and UHS speed class 1. Note that the speed class indicates performance of microSD cards and all the functions may not be performed at the speed class rate. ・ Although a microSD card can be used on other compatible device, data which is transferred from the other device may not be viewed/played on the terminal. Also, data saved to the microSD card from the terminal may not be viewed/played on another devices.
4 Hold the terminal horizontally, insert the tray with the card into the terminal, and then push it straight. ・ Check the orientation of the terminal and the tray. 5 Push the tray into the end, firmly press each point indicated with , and then make sure that there are no gaps between the terminal and the cover. ・ When the terminal is turned on, appears on the status bar.
Removing microSD card 1 Draw the cover of docomo nano UIM card/microSD card slot (P.30). 2 Pull out the tray straight from the terminal (P.39). 3 Remove the microSD card from the tray. 4 Hold the terminal horizontally, insert the tray into the terminal, and then push it straight. ・ 5 Check the orientation of the terminal and the tray. Firmly push the tray into the end and make sure that there are no gaps between the terminal and the cover (P.40). FCC ID To view the regulatory compliance mark.
Charging The internal battery is not fully charged at the time of purchase. ・ Estimated charging time (P.244) ・ To check performance of the internal battery, from the Home screen, tap [apps folder]u [Settings]u[About phone]u[Battery life]. Before charging It is recommended to use the AC Adapter 07 (optional) for charging. For handling the AC Adapter 07, refer to the AC Adapter 07 manual. ・ The AC Adapter 07 is compatible with 100V to 240V AC.
If you start charging with the terminal powered off, the screen indicating charging status activates although you cannot operate the terminal. Therefore, do not charge the battery in a place where the powering off is required. ・ You can check the latest charging equipment compatible with the terminal in the DOCOMO online shop. https://onlineshop.smt.docomo.ne.jp/ options/search.
Charging with AC adapter 3 When using AC Adapter 07 (optional) for charging, do the following procedures. 1 Insert the Type-C plug of the AC adapter horizontally into the USB Type-C jack of the terminal. 2 Unfold the power plug of the AC adapter and insert it into a power outlet. ・ When charging is started with the power on, the charging start sound is heard and the notification LED of the terminal turns on (P.68).
Charging with a wireless charger Before charging with Wireless charger 04 (optional), refer to the manual supplied with the product. ・ Products with marks conform to the wireless charging standards developed by Wireless Power Consortium (WPC). Notes on wireless charging When charging, meet the wireless charging touch point of the terminal (P.35) to the wireless charger correctly. ・ If you attach a cover (commercially available), etc. to the terminal, remove it and then charge the terminal.
If the installation screen for the terminal's driver software appears on your PC, please wait a moment for the installation to complete. ・ When the confirmation screen of installing software appears on the terminal, tap [SKIP] or [CANCEL]. ・ Charging with a PC To charge the terminal by connecting to a PC, USB cable A to C 02 (optional) is required. 1 Insert a Type-C plug of the USB cable A to C horizontally into the USB Type-C jack of the terminal.
Turning power on/off Turning power on 1 Press and hold the power key for at least 3 second. The terminal vibrates and the lock screen appears after a while. ・ When you first turn on the power and " ようこそ (Welcome)" is displayed, follow the onscreen instructions to make the initial settings (P.48). ❖Information If the notification LED flashes in red several times or the low battery icon is displayed when you press the power key with the terminal powered off, the battery level is not sufficient.
Unlocking the screen lock The lock screen appears when you turn on the power or press the power key to exit from sleep mode. ・ When Ambient display (P.189) is activated, double-tap the screen or press the power key to display the lock screen. 1 On the lock screen, swipe (flick) the screen. ❖Information On the lock screen, swipe (flick) or to use Google Assistant or the camera. ・ You can change the screen lock unlocking method (P.197).
2 When the initial settings screen for docomo service appears, tap of "Agree to above"u[NEXT]. Follow the onscreen instructions to make the following confirmations and settings. - d ACCOUNT settings - Set all docomo services - Review additional apps - “Anything else?” settings ・ If the confirmation screen for use of functions appears, follow the onscreen instructions. ・ 3 When the setup completion screen appears, [FINISH].
Setting up d ACCOUNT d ACCOUNT is an ID/password to use applications or services provided by DOCOMO. With d ACCOUNT, you can use various services more convenient regardless of line type such as LTE, Wi-Fi, etc., or device type such as smartphone, tablet, PC. When you do not set up d ACCOUNT in the initial settings, you can set as follows. 1 From the Home screen, tap [apps folder]u[Settings]u[docomo service/cloud]u[d ACCOUNT setting]. ・ 2 If the d ACCOUNT confirmation screen etc.
・ ■ The PIN Unlocking Key is written on the subscription form (copy for customer) handed at the subscription in the docomo Shop. If you subscribed other than docomo Shop, you must bring your official identification (such as driver's license), the docomo nano UIM card with you to the nearest docomo Shop or contact the "General Inquiries" on the last page. PIN/Password for screen lock It is a security code for using the screen lock function of the terminal (P.197).
■ PIN Unlock Key (PUK code) The PUK code is an 8-digit number for canceling the locked PIN code. The PUK code cannot be changed by yourself. ・ If you failed to enter PUK code 10 times consecutively, the docomo nano UIM card is locked. Please contact a docomo Shop. Unlocking PIN lock 1 2 3 By entering PIN code when powered on, you can protect from improper use. 1 2 From the Home screen, [apps folder]u[Settings]u[Security]u [SIM card lock]u[Lock SIM card]. Enter PIN codeu[OK].
Basic operations Operations on the touch screen ■ Touch an item such as icon or menu with your finger lightly and release it. ・ Double-tap means tapping twice quickly. Basic operations Using the touch screen Precautions on using touch screen Touch screen is designed for being touched lightly with fingers. Do not push the touch screen hard with a finger or press sharp objects (nail, ballpoint pen, pin, etc.) against the screen. ・ Touching the touch screen may not work in the following cases.
■ Pinch Touch the screen with two fingers and widen (pinch-out) or narrow (pinch-in) the fingers' distance to zoom in/out screen display. Using Side sense Side sense is a feature that supports onehand operations by the side edge of the screen. ・ You can use Side sense in any screen (it may not be available depending on operating condition or displayed function).
Double-tap the side edge of the screen to open the Side sense menu where you can activate applications or turn on/off the functions. Slide up the side edge of the screen to display the Multi-window menu where you can activate the Multi-window (split screen). Also, slide down the side edge of the screen to undo the operation (return to the previous screen).
Using the Side sense menu 1 Double-tap the side edge of the screen ・ ・ The Side sense menu appears. If the explanation appears, tap [START]. You can practice the operations by tapping [TRY SIDE SENSE TUTORIAL]. e More apps ・ Display more applications that are not currently shown in the application icon list. f Multi-window ・ Switch to the Multi-window menu (P.57). g Advanced ・ Open the "Side sense" in Settings menu (P.191).
Using the Multi-window menu You can activate Multi-window (split screen) using Side sense. ・ Operations in the split screen (P.74). 1 Slide up the side edge of the screen ・ ・ The Multi-window menu appears. If the explanation appears, tap [START]. a e b c f d g b Pairs of applications (Combination) ・ Pairs of applications which are predicted by your usage condition are displayed. ・ You can also set to display your desired pairs (P.191). c Exit Multi-window ・ Exit Multi-window (split screen).
Basic key icon operation The following operations can be performed by tapping the key icon shown in the bottom of the screen. Switching portrait or landscape view automatically You can set the screen orientation to switch between landscape and portrait view automatically according to the terminal orientation. 1 Back Home History Go back to the previous screen. Or close the menu, the Notification panel, etc. Go to the Home screen. Touch and hold the icon to open the Google Assistant.
If the sound volume is adjusted in "Ring and notification volume" (P.193) in silent mode, the silent mode setting is canceled. ・ You can adjust media sound by dragging up/ down the slider on the volume control bar which appears when the volume key is pressed. Tap to display the sound volume screen and you can change the volume of call sound, ringtone and notification sound, and alarm sound. ・ Capturing the displayed screen You can capture the currently displayed screen as a still image (Take screenshot).
2 3 [Emergency mode]u[IMPORTANT INFORMATION]uConfirm the important informationu[CLOSE]. Mark "I have read the important information"u[TURN ON]. ・ The terminal restarts. ❖Information To cancel Emergency mode, operate any of the following (The terminal restarts when canceling). - Press and hold the power key for at least 1 second u[Emergency mode]uTap [TURN OFF]. - Drag the status bar downuOpen the notification of emergency mode (P.71)u[Emergency mode is on]u[TURN OFF].
❖Information ❖Information Some tasks may require you to select an application each time, with "JUST ONCE" or "ALWAYS" not displayed on an application selection screen. ・ To deselect the application which is set to "ALWAYS", from the Home screen, tap [apps folder]u[Settings] u[Apps & notifications]u[SEE ALL XX APPS]uTap an application you want to cancel the settingu [Advanced]u[Open by default]u[CLEAR DEFAULTS].
Character entry Enter characters using the software keyboard (On-screen keyboard) which appears when you tap the character input box in a mail, phonebook, etc. Input method is set to "Gboard" by default. ❖Information To hide software keyboard, tap displayed at the lower left of the screen. ・ For details on Gboard, in the character entry screen, tap u u[Help & feedback] and then refer to Support.
Adding the layout for Japanese keyboard To use the layouts other than 12 keys, add them beforehand. 1 2 3 In the character entry screen, u[Languages]. [Japanese 12 keys]. Put checkmarks to the layoutsu [Done]. Character input method When you tap a key on the software keyboard, candidates list for the entered characters appears. Tap a word to enter from the candidate list, text can be input one after another. Japanese keyboard in 12 keys and QWERTY layouts is explained in this section.
c j Shows characters entered by Multi-tap input (P.66) in the order that is reverse of the regular one. Or undoes character conversion after it is decided. d Moves the cursor to the left. Or changes range of character conversion when it is not yet decided. Swipe (Flick) up/down to move the cursor to the other entry field (the operation may not be available depending on condition). e Display the list of emoji/sticker/smiley etc. In QWERTY keyboard, enters a punctuation mark.
Using the tool icon Flick input Tap the tool icon on the tool bar to operate as follows. Touch a key of 12 keys to display a character, number, or symbol that are assigned to the key. Flick to the direction of a target character etc. to enter the character. ・ On the QWERTY keyboard, flick each key up or down to enter number or symbol. Display the list of emoji/sticker/ smiley etc. (Clipboard) Quote characters saved to the clipboard and enter characters. (Settings) Display the Settings screen.
Multi-tap input On the 12 keys keyboard, tap the same key consecutively to enter a character, number, or symbol that are assigned to the key. To enter characters etc. assigned to the same key consecutively, wait until the color of the cursor indicating the conversion range is changed (approx. 1 second) and then enter the next character. To enter the next character soon, tap to change the color of cursor.
❖Information To paste a copied or cut character string, touch and hold a position to insertuTap [Paste]. When text is already entered, tap a position to insertu uTap [Paste]. ・ On some applications, these functions may not be available or the editing menu may appear different. Setting character entry ・ Personal dictionary Add words to Personal dictionary beforehand to have them appeared preferentially in the candidate list when entering characters.
Notification LED Notification LED provides information on the terminal status, incoming calls, mail reception, etc.
Status icon *1 The main status icons displayed on the status bar are as follows. Signal strength*1 5G available 4G (LTE) available*2 During International roaming Out of service Connected to Wi-Fi*1*3 Connected to a Wi-Fi network with no access to the Internet. The Wi-Fi signal is poor.
New voice mail ― Notification from Schedule/Memo P.96, P.165 Stopwatch is running* P.167 Timer is in use* P.167 Alarm is sounding/Alarm is snoozing/ P.166 Next alarm exist Playing a truck in Music P.161 P.156 Watching TV*/Notification of reserved watching Recording TV*/Notification of P.160 reserved recording Auto Exit Timer of TV watching is set P.158 Creator mode is active P.188 Dynamic vibration is worked P.192 together USB device is connected/Moisture on P.182, USB Type-C jack is detected P.
c Notification panel When the notification icons appear on the status bar, you can open the Notification panel to check the notifications, activate corresponding application, etc. 1 Drag the status bar down. a b a e c f e d g Quick setting tools ・ A part of the quick setting tools (P.72) are displayed. ・ Tap it to turn on/off each function. ・ Touch and hold it to display the setting screen, etc. depending on function. b Open the Quick settings panel ・ Drag down to open the Quick settings panel (P.
g CLEAR ALL ・ It appears when there are any notifications that can be cleared to clear all notifications. However, some notifications may not be cleared. ❖Information Quick settings panel Set ON/OFF etc. of each function. 1 To close the Notification panel, tap or drag the Notification panel up. ・ Even when the notification icon is not displayed on the status bar, the notification etc. indicating the terminal status may be displayed.
Airplane mode Silent mode (XXXX)* Location Flashlight STAMINA mode Hotspot Dolby Atmos Enable/disable Airplane mode. Set silent mode. Enable/disable location information. Set ON/OFF of the flash/photo light. Enable/disable STAMINA mode. Set ON/OFF of portable hotspot function. Set ON/OFF of Dolby Atmos. * In "XXXX", the silent mode type appears. c EDIT ・ Display the edit screen to add, delete or rearrange the quick setting tools. ・ In the edit screen, u[Reset] to restore to the default.
Split screen Split the screen to display and operate two applications at the same time. ・ Activate the applications to display beforehand. ・ Split screen may not be available depending on application. 1 2 . ・ Tap an icon appeared in the top of a thumbnailu[Split screen]. ・ 3 Applications are displayed as thumbnails. For applications which are not available for the split screen, "Split screen" does not appear. Tap the application thumbnail to display from the lower part of the screen.
3 Display the application thumbnail or the name you want to switch to. Swipe (flick) the thumbnail left/right (up/down in the landscape view) to display the thumbnail or name of the application you want to switch to. ・ Alternatively, tap [All apps] displayed in the left/right end (upper/lower end in the landscape view) of the thumbnail lineuTap the application to display it. ・ 4 [Done].
Searching information in the terminal and websites Enter a word in the search box to search the information in the terminal or on the Internet. 1 From the Home screen, tap the Google search widget. 2 Enter a keyword to search. 3 Tap the search suggestion or the software keyboard. ・ ・ Character entry (P.62) The search candidate list appears. of ❖Information Alternatively, from the Home screen, tap [Google]u [Google] to open the "Google" application.
Home screen Switching the home app You can switch the home app for the terminal to "docomo LIVE UX", "Xperia Home" or "Simple Home". ・ "docomo LIVE UX" (P.77) ・ "Xperia Home" (P.85) ・ "Simple Home" (P.88) 1 From the Home screen, [apps folder]u[Settings]u[Apps & notifications]. 2 3 [Default apps]u[Home app]. Tap any of [docomo LIVE UX]/ [Simple Home]/[Xperia Home].
c Home screen layout In Home screen, you can activate applications or use widgets. All applications can be added to the Home screen. ・ Swipe (flick) the Home screen left or right to switch the pages. ・ A dot or number may appear on upper right of application icon or folder when the application has a notification. a b g c d e f a h i Widgets ・ Activate widgets (Google Search). ・ Touch and hold to display the shortcut menu where you can perform certain operations.
Managing the Home screen Moving application icon, etc. 1 In the Home screen, touch and hold an icon you want to move. ・ 2 The shortcut menu appears. 1 To move to the next page, drag it to left/right end of the Home screen. ・ Alternatively, tap [Move] in the shortcut menu and then drag an application icon, etc. ・ The shortcut menu appears. [Remove from Home]. ・ In the Home screen, touch and hold an icon of application you want to uninstall. ・ ・ The shortcut menu appears.
Renaming folder 1 2 3 Changing wallpaper In the Home screen, tap a folder. Tap the folder name. Enter a folder name. ・ When entry is finished, tap software keyboard. on the Setting Home screen 1 1 Touch and hold an area of the Home screen where no icons, etc. are displayed. Create folder Add a folder. Wallpaper and Change wallpaper or Kisekae. Kisekae Create widgets Display widgets list.
Setting Machi-Chara display display 1 2 Touch and hold an area of the Home screen where no icons, etc. are displayedu[Home setting]u [Machi-Chara setting]. / of " キャラ表示 (Show character)". Using Osusume Apps Recommend applications or services according to your usage condition. 1 2 From the Home screen, [Recommends]. 3 Select an application or service. ・ Managing pages 1 Touch and hold an area of the Home screen where no icons, etc. are displayedu[Home screens].
Searching an application It is a function which allows you to search an application in a list sorted by used or installed order, or by an application name. 1 2 3 From the Home screen, ・ 4 . . In "Search app" field, enter an application name. Tap [By most recently used]/[By installation date]/[By app name] to display all applications in a list sorted by the specified order. Select the application. ・ ・ The application activates.
4 Setting the category display [RESTORE]. ・ If you selected "Restore from backup data list", select the data you want to restoreu[Restore]u[RESTORE]. My Magazine My Magazine is a search service for displaying articles in categories you selected. With tendency of articles you read and your profile information, the more you use, the more it comes close to your preference. Also, you can set to enable notifications, or customize My Magazine using location information, your docomo service subscriptions, etc.
my daiz NOW my daiz NOW is a service which delivers convenient information according to your preference or behavior. You can readily check information which is convenient for daily life such as weather, traffic, or gourmet. Displaying my daiz NOW 1 In the left end page of the Home screen, swipe (flick) right. In the right end page of the Home screen, swipe (flick) left. ・ Swipe (flick) up or down to switch cards to be displayed. ・ Swipe (flick) left or right to return to the Home screen.
Home app information Xperia Home screen You can check the version information, etc. of docomo LIVE UX. 1 2 From the Home screen, [About]. ・ u . This section describes the Home screen displayed when the home app is set to "Xperia Home". If the update of docomo LIVE UX is available, "Update now" is displayed in the application information screen. Tap it to update docomo LIVE UX. a b g c h d c e f a b Widget : Clock widget Machi-chara ・ Tap to ask something you want to know through dialog.
e Dock ・ Locate shortcuts (applications) or folders. They are always displayed even if the page of the Home screen switches. f Widget : Google Search g Wallpaper h Widget : 21:9 Multi-window ・ Tap to display the Multi-window menu (P.57). Adding folders on the Home screen You can put shortcuts etc. added to the Home screen into a folder to organize them. 1 ❖Information ・ ・ ・ ・ ・ ・ ・ Swipe (flick) the Home screen up to open the Application screen.
2 [Widgets]uTouch and hold a widget to add. When the Home screen appears, drag it to anywhere. ・ If the settings screen etc. appears, follow the onscreen instructions. ・ ❖Information If a frame is displayed when a widget added to the Home screen is touched and held, you can drag the frame to resize the widget. ・ To remove a widget, on the Home screen, touch and hold the widgetuDrag it to "Remove" which appears at the top of the screen.
a Simple Home screen This section describes the Home screen displayed when the home app is set to "Simple Home". Set Simple Home to use the home screen and the setting menu that are limited to the basic functions. 1 From the Home screen, [apps folder]u[Settings]u[Apps & notifications]. 2 [Default apps]u[Home app]u [Simple Home]. [OK]. 3 ■ ・ To set the font size to "Largest", put a checkmark "Set font size to Largest". Machi-chara ・ Tap to ask something you want to know through dialog.
Using Speed dial Register frequently used contacts to "Speed dial 1" - "Speed dial 3" to make calls or send emails easily. Saving contacts Register a frequently used contact to "docomo phonebook" application in advance. 1 2 Sending a message of +Message/ email 1 On the Simple Home screen, select the speed dialu[Send message]/ [Send email]. How to send a message via +Message (P.120) ・ How to send Gmail (P.124) ・ On the Simple Home screen, tap any of [Speed dial 1]/[Speed dial 2]/[Speed dial 3]u[OK].
Sound Using Settings 1 On the Simple Home screen, [Settings]. Phone number Display Brightness Adaptive brightness Auto-rotate screen Font size Sleep Screen lock Your own phone number is displayed. Adjust the screen brightness. Adjust the screen brightness automatically according to the ambient brightness, etc. with reference to the brightness set in "Brightness". Set whether to switch portrait/landscape view automatically according to the terminal orientation. Set font size.
Changing applications on the Simple Home screen 1 2 3 On the Simple Home screen, [Settings]u[Customize Home]. [Change apps]/[Reorder apps]. Select the applicationuSelect the application to newly display/select the location to move to. ・ 4 Application screen When the home app is set to "Xperia Home", all applications are displayed in the Application screen. ・ Switching Home app (P.77) 1 Swipe (flick) the Home screen up.
d Machi-chara ・ Tap to ask something you want to know through dialog. ❖Information A dot or number may appear for the application icon or folder when there is a notification from the application. ・ Adding an application to the Home screen Add shortcuts of application to the Home screen. 1 In the Application screen, touch and hold an application icon. ・ ・ 2 The shortcut menu appears. To add applications from a folder, tap the folder and then touch and hold an application icon.
3 [UNINSTALL]. 4 [OK]. ・ For applications that cannot be uninstalled, "UNINSTALL" is not shown. When "DISABLE" is displayed, you can disable the application (P.185). Editing the Application screen ❖Information To close the rearrange screen, u[Exit], or tap . To take out an application icon from a folder, tap the folderuTouch and hold the application iconuDrag it to a place you want to locate. ・ To rename a folder, tap a folderuTap the folder name, or tap [Unnamed Folder].
Application list Preinstalled applications are as follows. The descriptions when the home app is set to "docomo LIVE UX" are explained here. ・ For usage of some applications, separate subscription (Charged) is required. ・ For some applications, you can check functions or operation steps from the help. ・ Design of application icon or folder where the application is stored may be different depending on the home app.
地図アプリ (Map application)*1 An application which supports your outings totally according to multiple means of transportation as a car, walk, train. To use a part of features such as navigation, subscription to the charged service is separately required. Data Copy*1 An application that allows you to transfer data when changing model, back up to/restore from a microSD card. → P.168 データ保管 BOX (Data Storage BOX)*1 An application for using Data Storage BOX.
Jspeak*1 An application for translating spoken words into the listener's native language. Use Face-to face translation/Phone translation/Image translation/Common phrase to enjoy communication with the other party who speaks different language. Files*1 You can search data such as still images, videos, music, or downloaded files. → P.211 Photos You can playback photos or videos. You can back them up to your Google account. → P.
Cinema Pro With the special features for cinema imaging and color representation, you can enjoy professional-like movie shooting. → P.145 d 払い (d payment) An application for use "d 払い (d payment)", the payment service provided by DOCOMO. You can do your shopping simply, convenient and with good bargain just by showing a barcode displayed on the application in the target stores.
Gmail*2 You can use the email services provided by Google and major Internet service providers. → P.124 Google*2 Search information in the terminal and websites by keywords. → P.76 Google Pay*2 An application for managing electronic money or point cards collectively. iD アプリ (iD application)*1 An application for using "iD", electronic money offered by DOCOMO.
TikTok TikTok is a short music video community. You can communicate with others, shoot music video, or post videos. Video & TV SideView*1 Play videos. In addition, view the TV program guide or use your terminal as a remote for Sony televisions or other devices. Xperia ガイド (Xperia guide) Display Xperia 使いこなしガイド (Xperia use guide) to read explanation of the functions or check how to use them.
Phone/Phonebook Making/Receiving a call ・ With VoLTE (HD+), you can make voice calls with sound that is much higher quality than with VoLTE. To use VoLTE (HD+), the usage requirements of VoLTE must be met, and both you and the other party must have models which support VoLTE (HD+). Making a call 1 2 From the Home screen, u Enter a phone numberu . 3 When the call is finished, ・ Tap . to delete the number. .
Emergency call Emergency call Police call Fire and emergency rescue Coast guard Phone number 110 119 118 ❖Note ・ When calling 110, 119 or 118 from the terminal, tell that you are calling from a mobile phone, and give your phone number and your current location precisely for checking callback from the Emergency call acceptance organization such as police. Also, make a point to call in a stationary position to prevent the call from being dropped.
Entering pause (,)/(;) to send For using services requiring entry of number during a call such as check of the balance of a bank account, reservation of tickets, etc., enter an additional number to a phone number beforehand and make a call. ■ 1 2 3 ■ Making an international call (WORLD CALL) Using 2-second pause (,) WORLD CALL is a service for making international calls, which is available from DOCOMO's mobile phones in Japan. For details on WORLD CALL, refer to NTT DOCOMO website.
e Receiving a call When a phone comes in, the incoming call screen appears. ・ If the screen is on (except on the lock screen) or an application is running, the notification appears at the top of the screen (P.104). 1 2 ■ Swipe (flick) screen. up on the incoming When the call is finished, Voice call incoming screen a . e b Name/phone number of the other party ❖Information When "Answer" of "Suguden setting" (P.109) is ON, an incoming call can be answered just by holding up the terminal to your ear.
Muting the ringtone for an incoming call 1 While receiving a call, press the volume key or the power key. ❖Information You can stop vibration by pressing the volume key or the power key when silent mode (Vibrate) is set. ・ To adjust the volume of ringtone or listening volume, press the volume up/down key with the Home screen, etc. displayed and then tap .
j Operations during a call On the Calling screen, you can set voice output or mute, or enter a phone number to make a call to another party. ■ Screen displayed during a voice call a b ❖Note ・ Do not bring the terminal close to your ear with the speakerphone on to avoid from hearing damage. ❖Information g To hold/add a call, "Call waiting" subscription is required (P.108). ・ The notification icon appears on the status bar while dialing, incoming, calling or holding.
c Call history Incoming calls and outgoing calls are displayed by chronological order in the call history screen. Displaying the call history 1 ■ uTap From the Home screen, "Call History" tab Call History screen a b f g c d An image set to a contact etc. ・ Tap to display the profile screen of the Contacts. d History ・ The call type (outgoing call/incoming call/missed call), number of calls, how long ago, etc. are shown.
4 [SAVE]. Answering Machine Deleting a call history uTap 1 From the Home screen, "Call History" tab. 2 Touch and hold outgoing history/ incoming historyu[Delete]. ❖Information To delete all the call history, in the call history screen, tap u[Call history]u u[Clear call history]u [OK]. ・ Displaying missed calls When you have missed calls, the status bar. 1 2 appears in Drag the status bar down. [Missed call].
Checking the Answering Machine message in the status bar When you have any recorded messages, displayed in the status bar. 1 Call settings is Drag the status bar downuTap notification from Answering Machine. 1 2 A list of Messages in Answering Machine is displayed. ・ To play a message of Answering Machine, tap the message. ・ To delete a message in the Answering Machine, touch and hold the message in the message listu[Delete]u[OK].
Network English service guidance Remote operation settings Public mode (power OFF) setting Roaming settings Answering Machine Call Blocking Reject call with message Suguden setting Contact docomo* Switch the voice guidance to English or Japanese. Set to operate Voice Mail Service or Call forwarding Service using land-line phone, public phone or DOCOMO mobile phone, etc.
You can make a call to the other party that is registered in advance or recorded to the call history by shaking the terminal once with the Home screen displayed and then placing it to your ear. Mute, Reject Mute the incoming ringtone or reject a call by placing the terminal horizontally with the screen faced down while a call is incoming, or shaking the terminal twice. You can select from "Mute", "Reject", or "Reject and send SMS". Call ranking Check the other party whom you called many times.
When disconnecting (Motion)/muting or rejecting a call, flipping over the terminal on a black desk, etc. may cause the operation (Disconnect (Motion)/Mute, Reject) to fail. In this case, instead of placing the terminal directly on the surface, flip over the terminal about 1 cm above the desk etc. to operate (Disconnect (Motion)/Mute, Reject). ・ When Suguden features are available, the notification icon appears. You can also confirm notification detail from the Notification panel.
● Mute (Hold)/Disconnect (Voice command) ・ While calling with Mute (Hold) or Disconnect (Voice command) ON, other application using the mouthpiece/ microphone or a voice recording application etc. using the voice sound during a call may not be available. To use those application during a call, turn off the both settings of Mute (Hold) and Disconnect (Voice command) and then start calling.
Phonebook ■ On the Contacts screen, you can view names of contacts etc. You can set a photo or image to a contact, and display contacts by group. In the phonebook, you can enter various information for contacts, for example, phone numbers, mail addresses and various service accounts. c d a b Displaying phonebook 1 Contacts screen From the Home screen, [apps folder]u[docomo phonebook] ・ The Contacts list screen appears.
Managing phonebook Adding a new contact 1 From the Home screen, [apps folder]u[docomo phonebook]u ・ 2 On the profile edit screen, enter necessary information such as name. ・ 3 When you have set up Google account etc., select the account to save to. To add items, tap [More fields]. [SAVE]. Making a call from the phonebook 1 2 Editing a contact 1 2 ❖Information The contacts are listed in alphabetical order of the first names and then order of Japanese syllabary of the phonetic last names.
Adding a contact to Top Contacts 1 2 Contacts screen From the Home screen, [apps folder]u[docomo phonebook]u Select a contact you want to add to Top Contacts. My info On the profile screen, tap change to . International use setting Service quality improvement to ❖Information ・ ■ Contacts that you registered to Top Contacts are displayed in field in the Contacts screen. Alternatively, tap "Top Contacts" tab in the call history screen etc.
■ Profile screen Join/View joined contacts Delete Share Create shortcut Set ringtone Join/separate displayed contact. Delete a displayed contact. Send a displayed contact via Bluetooth function, Email, etc. Add shortcut of displayed contact to the Home screen. Set a ringtone for displayed contact. Setting label (group) to contacts 1 From the Home screen, [apps folder]u[docomo phonebook]u 2 [Create label]. 3 4 Set a name of label (group)u[OK]. uTap a contact to set the label (group).
Importing/Exporting/Sharing phonebook entries Phonebook entries can be imported from a microSD card or docomo nano UIM card, or exported to a microSD card. This is useful, for example, when you want to move the contact information to another phone. Also, sending all phonebook data via Bluetooth function, Email, etc. is available. ・ You can also use an online synchronization service to synchronize your contacts (P.202). ・ For exporting to/importing from a microSD card, insert a microSD card in advance (P.
Mail/Web browser docomo mail Send/receive mails using DOCOMO mail address (@docomo.ne.jp). Data can be easily transferred when changing models or restored when you have lost the terminal since sent and received mails are saved on the docomo mail server. Also, your d ACCOUNT allows you to use the same email address to send, receive, and view email on several devices, such as tablets and computers. For details of docomo mail, refer to NTT DOCOMO website. https://www.nttdocomo.co.
■ c Contact list screen a b c d e f g ■ Message list screen k h i j l m a Switching tabs ・ Tap to switch between displaying all contacts and only +Message users (contact with icon) to display. b My profile ・ Your own contact is displayed. Tap to display/edit my profile. Official Account ・ Tap to display official accounts. d Favorite contact ・ The contacts set to Favorites are displayed in the upper part of contact list, below "Official Account".
Sending a message 1 From the Home screen, [+Message]. 2 u u[New message]/[New group message]. ・ 3 4 ■ ab Group message is a function which allows multiple +Message users ( icon displayed in the contact) to exchange messages among them. g Select a recipient. c d To send a recipient who is not registered to Contacts, tap [Enter name and phone number] and input a phone number directly. ・ For group message, select multiple recipients and then tap [OK].
d : Display a sharing menu to send photos, stamps, location information, etc. ・ While the sharing menu is displayed, you can use functions such as sending images or recording voice. e Message entry field ・ You can enter a message. f : Switch to the stamp selection screen g : Send an entered message. h Message delivery status ・ : The recipient has checked the message It is available only when the settings of "Use message read function" of both sender and recipient are ON.
Reading a message Sent/received messages are displayed in thread by recipient/sender. 1 2 From the Home screen, [+Message]. uSelect a message thread. ・ Deleting a message 1 From the Home screen, [+Message]. 2 3 uSelect a thread. Functions used for replying to messages (P.120) 2 3 4 From the Home screen, [+Message]. uSelect a thread. Touch and hold a messageu . Select a recipient and enter a messageu (Send). u Only messages on the terminal can be deleted.
Changing the settings of +Message 1 2 From the Home screen, [+Message]. u[MyPage]u[Settings]. Set for messages, back up/restore, etc. Official Set the notification sound for official Account accounts. Photos and Set for file attachment, etc. such as videos photos or videos when sending/ receiving. Screen display Set the theme color, or background of message screen. Notification Set notifications. Privacy Set a passcode, block list, etc.
Gmail You can use the email services provided by Google or by general providers. ・ Set up your Google account (P.49) or email account by following the onscreen instructions, if you have not already done so. ・ When a message indicating that auto-sync is off appears after you set up your Google account, follow the onscreen instructions to set. ❖Information (Send). 5 ❖Information To attach a file, when creating a Gmail, tap [Attach file] and select the file.
Early Warning "Area Mail" Area Mail is a service which allows you to receive earthquake early warning or tsunami warning, emergency warning related to weather etc. delivered by the Meteorological Agency, and disaster/evacuation information delivered by the national government or local governments without being influenced by congestion. ・ Area Mail is a free service for which subscription is not required. ・ Up to 50 messages can be saved.
Checking received Area Mail later 1 From the Home screen, [apps folder]u[Disaster kit]. 2 3 [Early Warning "Area Mail"]. Select an Area Mail from the Area Mail list. Deleting Area Mail 1 2 3 From the Home screen, [apps folder]u[Disaster kit]. [Early Warning "Area Mail"]. Mark Area Mail messages you want to deleteu[Delete]u [DELETE]. Setting Early Warning "Area Mail" Set whether to receive Area Mail, or set operations when receiving Area Mail. 1 From the Home screen, [apps folder]u[Disaster kit].
Set volume of beep sound of incoming Area Mail. ・ When it is set to ON, the terminal emits sound at the maximum volume even in silent mode. ・ When it is set to OFF, the terminal emits sound according to the alarm volume setting. Check screen Check the reception screen and the image and buzzer/ringtone sound for earthquake beep tone early warning, tsunami warning and disaster/evacuation information, emergency warning related to weather etc.
❖Information ・ Changing tabs To copy text in a web page, touch and hold a textu Drag or to select a range of textuTap [Copy]. 1 . ・ Adding a new tab Open multiple tabs and view websites. 1 2 From the Home screen, [New tab]. View website. ・ u u 2 A number in the icon explained in Step 1 varies by the number of tabs that are opened. Closing a tab 1 Opening incognito tab 1 2 u u ❖Information Around address entry field is displayed in gray with incognito tab.
Languages Changing Chrome settings 1 2 From the Home screen, tap u[Settings]. Sign in to Chrome Sync and Google services Search engine Passwords Payment methods Address and more Notifications Home page Themes Privacy Accessibility Site settings . Sign in to Chrome with your Google account. Make the sync setting or Google services. Lite mode Downloads About Chrome Set the search engine. Set whether to save the passwords entered to websites.
Managing bookmarks and history Checking history 1 You can check history, save bookmarks, etc. Bookmarking a website 1 2 From the Home screen, u Display a website to bookmark. u . Opening a bookmark 1 2 2 From the Home screen, [History]. Tap a history to check. u u ❖Information ・ ・ To delete history, tap of history. To delete all history, [Clear browsing data...]uSelect the period to clear the datauConfirm that "Browsing history" is marked, then tap [Clear data].
Shooting/sending images Please be considerate of the privacy of individuals around you when taking and sending photos using camera-equipped mobile phones. If you cause the public any trouble using the terminal, you may be punished under law or regulations (for example, nuisance prevention ordinance). Camera/Photos Camera All still pictures or videos that you capture on the terminal are stored into the internal storage or a microSD card.
j k Shooting screen a b c d e f g h i j k a l m n o Display area for status icons ・ When the settings such as Smile Shutter (P.138) and Save location (Geo-tagging) are set, the icons are displayed here. Also, when the battery level is low, a red battery icon and the battery level are displayed. b Auto focus frame ・ Appeared when the screen is tapped. ・ When you press the camera key halfway, a square frame appears. ・ When pupil of people is detected, a focus frame of Pupil AF appears (P.142).
❖Information ・ ・ ・ ・ ・ ・ The display and operations differ depending on the capturing mode etc. To adjust magnification in detail, do as follows. - Drag the zoom indicator up or down (for portrait view, left or right) - Set "Use Volume key as" (P.140) to "Zoom" and operate with the Volume key - Pinch-in/-out the screen Switch to triple-lens or zoom is not available when shooting with the front camera or depending on the capturing mode.
■ Main capturing mode and Still image size/Video size Capturing Still image size/Video size mode PHOTO Camera : Front camera : 4:3 (12MP) 4:3 (8MP) 16:9 (9MP) 16:9 (6MP) 1:1 (9MP) 1:1 (6MP) VIDEO Video camera : Front video camera : 4K Full HD Full HD 1080 × 1080 (1:1) Full HD (60 fps) HD 1080 × 1080 (1:1) HD Slow HD motion ❖Information For shooting in "Slow motion" mode, sufficient brightness is needed because of its high-shutter speed.
■ Shooting photos ■ 1 2 3 ■ Shooting with the shutter icon From the Home screen, [Camera]. Swipe (flick) the screen to display "PHOTO" mode shooting screen. Tap the shutter icon ( ・ 1 2 Shooting with the camera key From the Home screen, [Camera]. Swipe (flick) the screen to display "PHOTO" mode shooting screen.
■ Shooting with Hand Shutter When shooting with the front camera, turn your palm toward the camera to shoot automatically. You can take picture of yourself without operations such as tapping an icon etc. ・ Hand Shutter is available for shooting with front camera in "PHOTO" mode. It is not available for "Portrait selfie" mode. ・ Setting "Auto capturing" P.138 to "Hand Shutter" is required. 1 2 3 From the Home screen, [Camera]. Swipe (flick) the screen to display "PHOTO" mode shooting screen.
■ 1 2 3 4 ■ Shooting with the start/stop icon From the Home screen, [Camera]. Swipe (flick) the screen to display the shooting screen in "VIDEO" mode. Tap the start shooting icon ( Tap the stop icon ( ). ・ Tap the pause/start shooting icon ( ) to pause/resume shooting. 1 2 From the Home screen, [Camera]. Swipe (flick) the screen to display the shooting screen in "VIDEO" mode. 3 Tap the shooting screen. 1 2 Tap the shooting screen again to stop shooting.
■ Changing settings when shooting Set still image size. The larger the size of a photo, the larger its file size. Changing from the menu ■ The displayed icons or operations vary by the capturing mode, camera/front camera, or lens type. ・ Some settings cannot be used in combination with one another. ■ 1 2 From the Home screen, [Camera]. uSelect a setting item. 3 Change the setting. For some capturing modes, tap the shooting screen to set.
■ File format (4K) : "VIDEO" mode*1 ■ Select the compression format for shooting videos with 4K from "H.264" or "H.265 (HEVC)". ■ Set whether to tag photos/videos location information (geotag) for the shooting spot. ・ Location information is added when shooting if appeared on the shooting screen. ・ appears while acquiring location information. To pictures shot while acquiring location information, geotags are not added.
■ Use Volume key as Select the function from "Zoom", "Volume", or "Shutter" to assign to the Volume key for shooting. ■ Data storage Set the saving location for shot photos/ videos. ■ Launch with camera key Set the operation for activating the camera by pressing and holding the camera key for at least 1 second. Launch Camera app Only launch the camera. Launch Camera app and capture Launch the camera and shoot a still image. Launch Photography Pro Launch "Photo Pro".
■ Brightness/shade of color : "PHOTO", "VIDEO", "Slow motion" mode Tap to adjust brightness and shade of color. To make adjustments, drag the marker on the bar that appears on the shooting screen. Tap or to hide the adjusting bar and reset the setting. ・ When the brightness adjusting bar appears when tapping the shooting screen in "PHOTO" mode, consecutively tap (for portrait view, ) to display the color shade adjusting bar.
■ Pupil AF : "PHOTO" mode When a face of object is detected, the camera automatically focuses on the pupil and a green focus frame appears. Tap to change pupil to be focused. Tap anywhere other than face to cancel Pupil AF and display the auto focus frame. is displayed on the screen while Pupil AF is activated. When you tap it to turn to , the pupil AF is canceled and the focus changes to a face position. ■ ■ Switch of effect : "Creative effect" mode Tap to switch a type of effect.
c Using Photo Pro It provides with professional camera operatbility and features so that you can shoot more creative photos. * Available by system update. Activating Photo Pro From the Home screen, [Photo Pro]. 1 ■ Photo Pro screen a b c d e f g h i j k l m Data storage/image size/file format* ・ Storage of shot photos (Internal storage ( )/SD card ( )), available memory of storage, image size, and file format* are displayed. ・ In AUTO mode, the scene/condition icon also appears.
l Setting item area ・ Set Drive mode ( ), Focus mode ( ), Focus area ( ), EV ( ), ISO ( ), Metering mode ( ), Flash mode ( ), White balance ( ), Face detection/Eye AF settings ( ), or File format ( ) *. ・ Appearance of displayed icon varies depending on setting. ・ The settings for some items are restricted depending on mode or lens setting. m Lock ・ Lock the items on the left part of the screen and the setting item area to avoid unintended change of the settings when you hold the terminal.
e Using Cinema Pro Using Cinema Pro From the Home screen, [Cinema Pro]. ■ Cinema Pro screen 1 a b c d e a b f g hij Viewfinder Project setting ・ Parameters in the project setting affect an atmosphere of images for whole project including clips in the project. ・ Once you shoot a clip as a new project, change of the project setting is not available. Shot clips are saved to the project. ・ Tap u[Open project]u[New project] to create a new project.
Combining clips and creating a film 1 In the Cinema Pro screen, [All files]. ・ 2 3 Clips/still images shot in the ongoing project are displayed. u[Create final film]. Tap the clip in the order of combinationu[CREATE]. Photos View, playback, or manage photos or videos. Displaying photos or videos 1 2 Playing back a created film 1 2 From the Home screen, [Photos]. Tap a created film. From the Home screen, [Photos]. Tap the image or video. ・ ・ The photo or video is played.
Deleting files (photo, video) 1 2 3 4 From the Home screen, [Photos]. Touch and hold a file to delete. ・ You can also select multiple files by touching and holding a file and then tapping the other file successively. ・ [Delete] is displayed after you tap tap [Delete]. u[Delete from device]. , [Delete from device].
Apps d メニュー (dmenu) In dmenu, you can easily access sites recommended by DOCOMO or convenient applications. 1 From the Home screen, [d メニュー (dmenu)]. ・ Browser is activated, "d メニュー (dmenu)" appears. dmarket dmarket provides a variety of services, offering digital content, such as music, videos, and books, and giving you access to a shopping site, travel booking site, and other sites. 1 From the Home screen, [dmarket]. ❖Information ・ For details on dmarket, refer to the following website. https://d.
Installing an application Play Store Use Google Play to install useful applications or fun games to the terminal. ・ To use Google Play, you need to set up a Google account (P.49). ・ For details on purchasing applications, returning your purchases, or requesting a refund, see Google Play Help. ・ Once you accept the installation of an application, you will be held responsible for its use. Be careful especially about applications which access many functions or large amount of data.
Osaifu-Keitai This function allows you to use " おサイフケー タイ対応サービス (Osaifu-Keitai compatible service)" by which you can pay money or use as a point card. You can save electronic money and points to an IC card of the terminal and a docomo nano UIM card to check the balance or points on the screen. Also, you can prevent from being used without asking in case of theft or loss by locking Osaifu-Keitai function. For details on Osaifu-Keitai, see NTT DOCOMO website.
Notes on hovering over the device Please note the following when hovering the terminal over an IC card reader or NFC module equipped device. Enabling the NFC/Osaifu-Keitai function 1 From the Home screen, [apps folder]u[Settings]u[Device connection]u[Connection preferences]. 2 Tap ・ of "NFC/Osaifu-Keitai". The NFC/Osaifu-Keitai function is enabled. When the NFC/Osaifu-Keitai function is enabled, all of the OsaifuKeitai compatible services are available.
Using "Osaifu-Keitai compatible service" To use the Osaifu-Keitai compatible service, set services in the Osaifu-Keitai application. ・ Enable NFC/Osaifu-Keitai function in advance (P.151). 1 From the Home screen, [apps folder]u[Osaifu-Keitai]. ・ If the initial settings are not complete, the initial setting screen appears. Follow the onscreen instructions. 2 3 Select a service. Set the service. 4 Hold mark of the terminal over an IC card reader. ・ Set it from the service application or the website.
2 Tap of "NFC/Osaifu-Keitai lock ON/OFF". Setting "Osaifu-Keitai lock (UIM card)" Lock Osaifu-Keitai function in docomo nano UIM card. 1 2 3 From the Home screen, [apps folder]u[Settings]u[Security]u [Advanced]. [Osaifu-Keitai lock (UIM card)]u . Enter any passwordu[OK]. ・ The password is required for canceling the lock. Take notes etc. to avoid forgetting it. ❖Information Note that you cannot cancel "Osaifu-Keitai lock (UIM card)" if the battery runs out while "Osaifu-Keitai lock (UIM card)" is set.
TV TV is an application with which you can switch between Full seg and 1seg and watch them according to the airwave reception. In addition, since the data broadcasting can be received with images and sounds, interactive service using communication function of mobile devices and receiving detailed information are available. With Full seg, you can watch a terrestrial digital TV broadcasting service in high-vision quality.
Changing the direction of the TV antenna cable or moving to another location may improve signal reception. TV antenna cable To watch TV with the terminal, use the supplied TV Antenna cable SO02. 1 ❖Information ・ To output audio sound of the TV from a commercially available earphone or headphone, connect it to the supplied TV Antenna cable SO02. When connecting an earphone or headphone, insert the plug straight and firmly into the end of headset jack of TV Antenna cable SO02.
h Channel, broadcasting station and program information i Reception signal level j Start shooting k Channel selection key ・ Touch and hold / to search available channels. ・ Tap to to display the channel list. l Data broadcasting ・ On the 1seg watching screen, data broadcasting can be viewed only in the portrait screen. m Data broadcasting remote control Watching TV From the Home screen, [apps folder]u[TV].
It may take a time to acquire image data or broadcasting data when you activate TV or change channels due to characteristic of digital broadcasting. ・ According to the airwaves condition, image or sound may be interrupted or stopped. ・ Answering an incoming call while watching TV temporarily pauses the program. The program resumes automatically after the call ends. ・ To watch data broadcasting, call charge or packet communication charge is not required.
Display program information of the channel currently watched. ・ Select a TV program to show the detail information. ・ Select a programuTap on the program detail info screen to reserve viewing/recording of TV programs. Recorded program list Display recorded program list (P.160). Reserve Recording/ Reserve programs to record/ Viewing view, or display the failed reservation list (P.160). TV link Display TV link list.
Saving channels in the current location Available channels vary depending on the area (broadcasting service area) you are using in. Changing TV remote control number Change TV remote control number assigned to each broadcasting station. Each broadcasting station can be called up via the corresponding TV remote control number. 1 From the Home screen, [apps folder]u[TV]. 1 From the Home screen, [apps folder]u[TV]. 2 3 u[Change area]. Touch and hold an unregistered item.
Recording TV Record images, sound, captions or data broadcasting while displaying. ・ Data broadcasts can be recorded only in 1seg mode. 1 From the Home screen, [apps folder]u[TV]. 2 3 Tap to start recording. u[Stop recording]/[Stop recording as end of program]. ・ To end the recording when the program ends, tap [Stop recording as end of program]. ❖Information Continuous watching time (P.246) Recorded data is saved on a microSD card. Recording is not available if a microSD card is not attached.
Music When is displayed at the upper right of screen, music can be played with Google Cast devices. Tap and then follow the onscreen instructions to connect. To play music data on a Google Cast device, connect the terminal to the same Wi-Fi network as the one the Google Cast device connected in advance (P.172). ・ Use Music to play back music stored in the internal storage or a microSD card. ・ File formats of playable data (P.
Location services Your current location can be positioned using GPS, Wi-Fi, or mobile network. GPS function The terminal has a GPS receiver that uses satellite signals to calculate your location. Some GPS features use the Internet. Data rates and charges may apply. When you use GPS function to find your location, make sure you have a clear view of the sky. If GPS does not find your location after several minutes, move to another location.
■ Where radio waves are difficult to receive Note that radio waves may not be received or it may be difficult to receive radio waves in the following conditions, since GPS uses radio waves from a satellite.
Finding the current location on the map You can detect your current location using location information service. ・ To detect current location, enable "Use location" (P.163) beforehand. 1 Viewing Street view 2 3 1 2 3 From the Home screen, [Google] u[Maps]. Current location is shown by blue mark. ・ To show the current location when it is not shown, tap . ・ If you tap , the icon changes to , and then the terminal's geomagnetic compass links the direction displayed on the map.
Creating schedule event Schedule Displaying schedule 1 2 From the Home screen, [apps folder]u[Schedule]. u[Monthly]/[Week]/[Daily]. ・ Swipe (flick) the calendar left or right to display the next or previous month/ week/day. 1 2 3 uEnter the item. ・ For setting alarms, tap [Display input option]. [Save]. ❖Information ・ ❖Information To move the cursor to the current date, in Step 2, tap u[Jump to]u[TODAY].
Setting display conditions in Schedule When a search criteria is set, specified data can be displayed. 1 2 3 From the Home screen, [apps folder]u[Schedule]. u[Conditions]. Select the display conditionu[OK] u . ❖Information ・ To search the contents entered in "title", "text" and "Where?", in Step 3, [Free word search]uEnter a search wordu[OK]u[OK]u . Clock Use alarm, world clock, stop watch and timer. Setting an alarm 1 2 From the Home screen, [apps folder]u[Clock]u"Alarm" tab. uSet a timeu[OK].
❖Information When you swipe (flick) it left, the alarm sounds again when the set time has passed (snooze). ・ Alternatively, you can operate by tapping the notification at the top of the screen when the display is on (except on the lock screen). Using Timer ・ Using World clock Display the date and time, time difference from the home city, etc. in cities around the world. 1 From the Home screen, [apps folder]u[Clock]u"Clock" tabu 2 Enter a city nameuSelect a city from the list.
docomo Data Copy docomo Data Copy application allows you to copy the data saved to the terminal to the other terminal or back up/restore the data. Use this application for transferring the data when changing the model or for the regular backup of important data. ・ Data may not be copied, backed up, or restored correctly depending on OS or file type. Data transfer You can copy the phonebook entries, images, etc.
If the battery is low, backup or restoration may not be done. In that case, charge the terminal and retry to back up or restore. ・ You can back up only the data such as still images and movies stored in the internal storage with this application. The data stored in a microSD card cannot be backed up. ・ The periodical backup cannot be executed at specified time if the screen is locked or "STAMINA mode" (P.187) is activated at that time.
Copying contacts to docomo account Copy contacts registered to your Google account to the docomo account. 1 From the Home screen, [apps folder]u[Data Copy]u[Backup & Restore]. 2 [Phonebook account copy]u [Select] of contacts to copyu [OVERWRITE] or [ADD]. ・ 3 The copied contacts are saved to your docomo account. [OK].
❖Information Settings Viewing the Settings menu 1 From the Home screen, [apps folder]u[Settings]. Network & internet Device connection Appearance Apps & notifications Battery Display Sound Storage Privacy Location Security docomo service/cloud Accounts Xperia Assist Accessibility Digital Wellbeing & parental controls Google System About phone The item indicating the set function may be displayed above the "Network & internet" depending on the condition of usage of the terminal.
Wi-Fi With Wi-Fi function, you can connect to an access point for your home, company network or public wireless LAN services to use mail and Internet. ■ Turning on Wi-Fi 1 2 Reception interference caused by Bluetooth devices Wireless LAN (IEEE802.11b/g/n) and Bluetooth devices use the same frequency band (2.4GHz). If you use the terminal near Bluetooth devices, reception interference may occur or the communications speed may deteriorate. Also, you may hear noise or have a connection problem.
❖Information Depending on your usage environment, the connection speed may be decreased, or Wi-Fi may not be available. ・ When the terminal is connected to Wi-Fi network successfully, "Connected" appears. If a different message is displayed, make sure of the password (security key). When the connection is not established even if you enter a correct password (security key), the correct IP address may not have been acquired. Check the signal status and reconnect.
Setting up Wi-Fi 1 From the Home screen, [apps folder]u[Settings]u[Network & internet]u[Wi-Fi]u[Wi-Fi preferences]. Turn on Wi-Fi Set whether to automatically turn automatically*1 on Wi-Fi when the terminal detects a saved high quality Wi-Fi network, and connect to it. Open network Set whether to notify you when any notification high quality Wi-Fi open network is detected. Auto-connect*2 Set whether to automatically connect to saved Wi-Fi network when it is detected for each Wi-Fi network.
❖Information Wi-Fi Direct function becomes available when you install a compatible application. ・ Enabling/Disabling mobile data communication 1 Mobile network 1 From the Home screen, [apps folder]u[Settings]u[Network & internet]u[Mobile network]. Mobile data Data roaming App data usage 4G Calling Preferred network type* Automatically select network* Choose network* Access Point Names* P.175 P.
Set data limit Data limit Set whether to temporarily suspend the mobile data communication when the mobile data usage reaches to the limit value. Set the limit value of mobile data usage. ■ 1 ・ ❖Information Displayed mobile data usage amount is an estimate and it may be different from the actual one. You can check your actual mobile data usage volume in My docomo. ・ Note that the mobile data communication will suspend when the mobile data usage reaches to the specified limit value.
❖Information Do not change the MCC/MNC. If you change them to the values other than the default (440/10), the access point will not be displayed on the APN screen. If the set access point is not displayed, in Step 2uTap [Reset to default], or tap and then set the access point again. ・ It is recommended that you use the access point that is registered by default as it is.
Using tethering function Use tethering function which allows wireless LAN devices, USB devices, or Bluetooth devices to access the Internet via the terminal as a modem. ❖Information If you want to use the tethering, use of Packet Pack/ packet flat-rate service is highly recommended. ・ Tethering function is not available when the docomo nano UIM card is not inserted, mobile data communication is disabled, or use of mobile network is not available due to out of service area.
5 Enter a password of the Wi-Fi access point to set as required. ・ 6 By default, a password is set in a random manner. [SAVE]. Enabling USB tethering 1 Connect the terminal to a PC with USB cable A to C 02 (optional) etc. (P.46). When a screen for requesting access to the device data appears, tap [DENY]. ・ When a screen for installing driver software appears, wait for a while until the installation is complete.
Airplane mode In this mode, the functions of using radio wave transmissions such as calling, accessing to the Internet (including sending/receiving mails), etc. are disabled. 1 2 From the Home screen, [apps folder]u[Settings]u[Network & internet]. of "Airplane mode". ・ appears on the status bar. ❖Information Even if Airplane mode is ON, Wi-Fi, Bluetooth function and NFC/Osaifu-Keitai function can be turned on. Do not turn on these functions in a place where the use of radio wave is prohibited.
Device connection 1 From the Home screen, [apps folder]u[Settings]u[Device connection]. Pair new device Connection preferences Setting Connection preferences 1 P.213 P.181 ❖Information When the terminal is connected to a device, the device information may be displayed above "Pair new device". Tap it to change the connection method, cancel connection, etc.
Set whether to display a confirmation screen for installing software which allows to manage the contents of the terminal when the terminal is connected to a PC. Restart USB When moisture is device auto- detected on the USB detection Type-C jack, automatic detection of USB device is stopped. Tap [Restart USB device autodetection] to resume the auto detection. DUALSHOCK™4 Set to allow a wireless controller (DUALSHOCK™4) to operate the terminal. Printing Install print service applications.
Apps & notifications 1 From the Home screen, [apps folder]u[Settings]u[Apps & notifications]. Display the list of recently activated applications. Tap an application to display the app info. SEE ALL XX APPS P.183 Configure notifications P.185 Screen time Check usage time per application, or set a timer for each application to restrict usage time of a day. Default apps Check/change the default application. Permission manager* Check/change the app permissions.
Battery* Open by default* version* Check the battery status from the last full-charge or set the use restriction in background etc. Clear the setting of default applications used for certain operations. Display the application's version. * Appeared when [Advanced] is tapped. ❖Information ・ The displayed items may differ or the item may not be selected depending on application or usage condition.
Disabling application You can disable some applications or services, that cannot be uninstalled. ・ Disabled applications are not displayed on the Home screen, etc. and you cannot execute them, but they are not uninstalled. 1 From the Home screen, [apps folder]u[Settings]u[Apps & notifications]u[SEE ALL XX APPS]. ・ 2 3 Tap u[Show system] to show all applications. Tap the application to disable. [DISABLE]uConfirm the content of the screen and then [DISABLE APP]. 2 3 u[Reset app preferences].
Keep notifications Allow notification snoozing*2 Suggested actions and replies*2 Allow notification dots*2 Use LED light to show incoming notifications*2 Notification sound*2 Set whether to keep the notification content displayed on the lock screen when you have any notifications. Set whether to allow notifications to snooze to display them again at specified time. To set snooze, drag the notification left or right in the Notification panel and tap .
Battery 1 From the Home screen, [apps folder]u[Settings]u[Battery]. XX% More than XX remaining* Apps are running normally* STAMINA mode The battery level and available time (estimate) are displayed. Battery usage condition, etc. is displayed. Restrict the operations and a part of functions of the terminal to save the battery power. ・ When "Set a schedule" is set to "Based on percentage", STAMINA mode turns on automatically when the battery level becomes to the specified level.
Display 1 From the Home screen, [apps folder]u[Settings]u[Display]. Set the display mode of still images or videos. Set whether to automatically apply the creator mode in specific applications, or check applications to be applied. ・ You can operate when the application that is available for the creator mode is installed. Video image Reproduce precise texture enhancement or sharp feelings by enhancing patterns and outlines when playing video.
Prevent accidental operations with screen off* Screen saver* Prevent unintentional operations by disabling the touch screen when the key of the terminal is accidentally pressed in a bag, pocket, etc. and the screen is turned on. Set the screen saver. * Appeared when [Advanced] is tapped. Adjusting the white balance 1 2 3 From the Home screen, [apps folder]u[Settings]u[Display]u [White balance]. of "Set manually" Tap any one of [Warm]/[Medium]/ [Cool]/[Custom].
1 From the Home screen, [apps folder]u[Settings]u[Display]u [Lock screen display]. Ambient display (Always-on display) When to show Ambient display New notifications Set a timing for activating Ambient display. Set whether to activate Ambient display when you have notifications in sleep mode. ・ This function may not be operated depending on notification. Sticker Set to display a specified image for Ambient display.
*1 Appeared when "Screen lock" (P.197) is set to "Pattern"/"PIN"/"Password". *2 Displayed items vary depending on the settings of "Screen lock". Setting Side sense Make settings for using Side sense feature (P.54). 1 2 From the Home screen, [apps folder]u[Settings]u[Display]u [Advanced]u[Side sense]. . TRY SIDE SENSE TUTORIAL Side sense menu Multi-window menu Practice the operations of Side sense. Set applications to be displayed in the Side sense menu.
Sensitivity Double-tap Adjust speed of doublespeed tapping operation that can be recognized on the side edge of the screen. Slide length Adjust recognition of sliding length for the side edge of the screen. Gestures Assign an action to double-tapping/sliding up/sliding down the side edge of the screen (Gesture operation). Enable Side sense on Set whether to display the lock screen Side sense menu on the lock screen.
Vibrate for calls Do Not Disturb Phone ringtone Notification sound Default alarm ringtone Dial pad tones* Screen locking sounds* Charging sounds and vibration* Touch sounds* Touch vibration* Set whether to vibrate the terminal while receiving a call. P.186 P.194 Set whether to emit sound when tapping the dialpad. Set whether to emit sound when pressing the power key to lock the screen, or unlocking the screen lock. Set whether to notify of start of charging with sound and vibration.
Setting the ringtone/ notification sound/alarm ringtone 1 From the Home screen, [apps folder]u[Settings]u[Sound]. 2 Tap any one of [Phone ringtone]/ [Notification sound]/[Default alarm ringtone]. 3 Select a sound optionu[OK]. ❖Information To set a ringtone other than ringtone, notification sound, or alarm ringtone preset by default, tap [Add ringtone]/[Add notification]/[Add alarm] in Step 3.
❖Information To increase available memory of the internal storage by selecting files and applications to delete/uninstall them, tap [Internal shared storage]u[FREE UP SPACE]. ・ Tap [Internal shared storage]u[Files], or tap [USB drive]/[SD card] to display the data list. You can check the saved data or copy/move/delete/share the data (P.211). ・ To release the recognition of USB storage/microSD card, tap of "USB drive"/"SD card". To recognize again, tap [USB drive]/[SD card]u[MOUNT].
Location Security 1 From the Home screen, [apps folder]u[Settings]u[Location]. 1 2 3 of "Use location". Read the attention on location information and tap [AGREE]. Google Play Protect*1 Display applications or services which use the recent location information data. Display all applications and services which use the recent location information data. App permission Check/change the app permission using location information.
The internal storage is encrypted by default. Show type of credential storage*4. Display trusted CA credentials. Manage the user credentials saved in the terminal. Install from Install certificates. SD card Clear Clear all certificates or credentials credential information stored in the credential storage.* 5 Trust agents*3 Set whether to enable Trust agent when the screen lock unlocking method is set to "Pattern"/"PIN"/ "Password". Screen pinning*3 Set whether to enable screen pinning.
of "Screen lock" as required. ■ To turn off the screen lock Make pattern Set whether to show pattern when the Home screen, [apps 1 From visible* entering pattern. folder]u[Settings]u[Security]u Lock after screen Set the time from when the screen [Screen lock]uEnter the set unlock timeout turns off to when the screen is pattern/PIN/passwordu[None]u locked automatically. [YES, REMOVE].
Setting up fingerprint authentication The terminal has a fingerprint sensor (P.34) and you can unlock the screen lock with the fingerprint authentication, touching it with the registered finger. Notes on using fingerprint authentication Your terminal recognizes a fingerprint based on its unique characteristics. For this reason, some users may not be able to use fingerprint authentication if their fingerprints are not sufficiently unique.
Registering your fingerprint 1 From the Home screen, [apps folder]u[Settings]u[Security]u [Fingerprint Manager]. ・ 2 If you have already registered fingerprint, the entry screen for unlocking the screen lock appears. Enter the unlocking method to display the Fingerprint Manager screen. Select the screen lock unlocking method. After this step, follow the onscreen instructions. When the registration is complete, the screen indicating addition of the fingerprint appears.
docomo service/cloud 1 From the Home screen, [apps folder]u[Settings]u[docomo service/cloud]. Set up your d ACCOUNT to use docomo applications (P.50). You can also use your biological information (fingerprint) registered on the terminal to set up your d ACCOUNT. docomo cloud Make settings for docomo cloud compatible service. docomo Set whether to use the function of Application Data automatic back up/restore data of Backup docomo apps, or check the list of apps whose backup data stored.
Accounts 1 From the Home screen, [apps folder]u[Settings]u[Accounts]. Add account Automatically sync data P.202 P.202 Adding accounts Add or remove online service accounts. ・ Set up your Google account (P.49) ・ Auto-sync data (P.202) 1 From the Home screen, [apps folder]u[Settings]u[Accounts]u [Add account]. 2 Tap the account type. ・ docomo account is set by default. Removing an account 1 From the Home screen, [apps folder]u[Settings]u[Accounts]u Select an account you want to remove.
Xperia Assist Accessibility You can check "Xperia 使いこなしガイド (Guide for using Xperia)" which introduces use of the terminal, or view the support page. Also, you can set for the battery or activate Xperia Lounge Japan. 1 From the Home screen, [apps folder]u[Settings]u[Xperia Assist]. Xperia 使いこなしガイド (Guide for using Xperia) STAMINA mode Battery Care Xperia Lounge Japan サポート (Support) View Xperia 使いこなしガ イド (Guide for using Xperia) to check function descriptions, how to use, etc. Set STAMINA mode (P.
Remove animations Set whether to turn off the animation effect of screen display. Click after mouse Set whether to perform click pointer stops operation when the pointer moving stops when using a mouse (commercially available) etc. Power button ends Set whether to end calls by call* pressing the power key. Auto-rotate screen P.58 Touch & hold delay Set response time for operation of touching and holding the screen.
Digital Wellbeing & parental controls You can prevent from overusing the terminal by checking your usage habits of the terminal, managing the usage time with the tool such as the app timer. Also, you can set the use restriction by guardian. 1 2 From the Home screen, [apps folder]u[Settings]u[Digital Wellbeing & parental controls]. Check and set each item. Google Check, change, or delete information or settings related to your Google account and the services.
Languages & input System 1 From the Home screen, [apps folder]u[Settings]u[System]. Languages & input Gestures Date & time Backup Back up to Google Drive Account*1 Reset Reset options*2 network settings Reset app preferences Erase all data (factory reset) Multiple users*2 System update*2 Application update*2 P.206 P.207 P.208 Set whether to back up data of applications, settings of the terminal, etc. to Google Drive. Set an account for backup to Google Drive.
Pointer speed* Text-to-speech output* Set speed of the pointer when using a mouse (commercially available) etc. P.204 * Appeared when [Advanced] is tapped. Changing the phone language 1 2 3 From the Home screen, [apps folder]u[Settings]u[System]u [Languages & input]u [Languages]. [Add a language]uSelect the languageuSelect the country or region as required. Drag of the language to the top layer ("1" position).
Date & time ・ To set date, time, time zone or 24-hour format manually, turn off "Use network-provided time", "Use network-provided time zone", or "Use locale default". 1 From the Home screen, [apps folder]u[Settings]u[System]u [Date & time]. Adjust date and time automatically by using network-provided information. Date Set date manually. Time Set time manually. Use networkAdjust time zone provided time zone automatically by using network-provided information. Time zone Set time zone manually.
❖Information Some pre-installed content can be re-downloaded, even if it is deleted when you reset your terminal. To download, from the Home screen, tap [apps folder]u[Xperia Lounge Japan]u u[ サポート (ブラウザで開きます)(Support (Open the window by the browser))]u[ スマートフォン/タブレット関連(プ リインストールコンテンツなどの再ダウンロード)(For smartphone/tablet (For re-downloading preinstalled contents))]u[ ドコモ (DOCOMO)] (in Japanese only) and then select the terminal on the displayed screen.
About phone 1 From the Home screen, [apps folder]u[Settings]u[About phone]. Register a name of the terminal. Phone number Your own phone number is displayed. Emergency information Register your blood type or the other information that can be useful for initial response in emergency or the contacts for emergency. Legal information Check third party's licenses or Google terms of use, etc. Certificates P.248 Detailed Diagnostics Set whether to send detailed diagnostics data of the terminal.
File management Storage structure Phone (Internal shared storage) Folders in the internal storage (/storage/ emulated/0) by default are as follows. ・ Displayed folders may differ depending on the terminal operations. Alarms Android DCIM Download Movies Music Notifications Pictures Podcasts Ringtones Stores alarm sounds etc. Stores setting data for system or each application, temporary files, etc. Stores still pictures/videos shot by Camera. Stores downloaded data through the web browser.
❖Information ・ To search data, tap in Step 2 and enter a file name, then tap of the software keyboard. ■ 1 2 3 4 5 ■ 1 2 3 4 5 Creating a folder From the Home screen, [apps folder]u[Files]. uTap the category or storage. Tap the folder as required. u[New folder]. Enter a folder nameu[OK]. Renaming a folder or file From the Home screen, [apps folder]u[Files]. uTap the category or storage. Tap the folder as required. Touch and hold a folder or file you want to rename.
Keep the Bluetooth device approximately 10 m or more away from a wireless LAN device. ・ Within approximately 10 m, turn off either the Bluetooth device or the wireless LAN device. ・ Data communication Bluetooth function Bluetooth function is a technology which enables to connect with Bluetooth device such as PC, handsfree headset wirelessly. ・ The terminal does not connect wirelessly with all types of Bluetooth devices. ・ Supported Bluetooth profiles (P.
・ Make sure that the Bluetooth function and Bluetooth detection function of the target device are on in advance. 1 From the Home screen, [apps folder]u[Settings]u[Device connection]u[Pair new device]. ・ Detected Bluetooth device names are displayed in "Available devices". 2 Tap a name of Bluetooth device for pairing. 3 Confirm the Bluetooth pairing code (pass code) on the confirmation screenu[PAIR]. ・ ■ Paired Bluetooth device names are displayed in "Currently connected".
Sending/Receiving data via Bluetooth function Turn on Bluetooth function in advance, then pair with a target Bluetooth device. Sending data via Bluetooth function 1 [Bluetooth] from the sharing menu of each application. 2 Tap the other Bluetooth device. Receiving data 1 Send data from the other Bluetooth device. ・ 2 appears on the status bar. Drag the status bar down u[Incoming file]u[ACCEPT].
External device connection 1 When a screen for installing driver software appears, wait for a while until the installation is complete. ・ When the confirmation screen of installing software appears on the terminal, tap [SKIP] or [CANCEL]. ・ Connecting to PC Connect to a PC to exchange data between the internal storage or the microSD card and a PC. ❖Information Appeared screen may vary depending on the operating system (OS) of a PC. ・ You may not be able to operate copyrighted data of images, music, etc.
Removing USB cable A to C safely ・ Do not remove the USB cable A to C during while transferring data. Data may be damaged. 1 Confirm that it is not transferring data, remove the USB cable A to C from the terminal and a PC.
International roaming Overview of International roaming (WORLD WING) With the international roaming (WORLD WING), you can use the terminal without changing phone number or mail address in the service area of the overseas network operator affiliated with DOCOMO. You do not need to change the settings of call and SMS. For details of International Roaming Service (WORLD WING), refer to NTT DOCOMO website. https://www.nttdocomo.co.
Before using overseas Advance preparation Network service settings Before leaving Japan To use the terminal overseas, check the following in Japan. ■ Subscription ・ ■ Charging ・ ■ Check if you subscribe WORLD WING. For details, contact "General Inquiries" on the last page. For charging, refer to NTT DOCOMO website. Usage charge Overseas usage charges (call and packet communication) differ from those in Japan. For details, refer to NTT DOCOMO website.
After arriving overseas When you arrive overseas and turn on the terminal, the terminal connects an available network automatically. Connectivity When "Automatically select network" (P.220) is set to ON, the most suitable network will be selected automatically. Setting network By default, the terminal automatically searches available network and connect to it. To switch network manually, set as follows.
Setting the preferred network type 1 From the Home screen, [apps folder]u[Settings]u[Network & internet]. 2 [Mobile network]u[Advanced]u [Preferred network type]. 3 Select the preferred network type to set. ・ Select "5G/4G/3G/GSM" to switch available network type automatically. Using VoLTE during international roaming Set to enable VoLTE when VoLTE is available during international roaming. 1 2 From the Home screen, [apps folder]u[Settings]u[Network & internet]. [Mobile network]u of "4G Calling".
Making/Receiving a call in the country you stay When you arrive overseas and turn on the terminal, an available network is automatically set. ・ Check that the battery and signal levels are high enough. ・ Depending on the network operator, even if the Caller ID notification is active, the caller ID may not be notified or appear properly. In this case, calls cannot be made from the call history.
3 4 . ・ Making a call to WORLD WING user overseas When the International dial assist screen is displayed, tap [CALL]. When the call is finished, . Making a call within the country you stay You can make a call by entering the phone number of the other party's land-line phone or mobile phone in the same way you do in Japan. 1 2 3 4 From the Home screen, Enter a phone number. ・ u . To make a call to land-line phone, enter the area code (city code), other party's phone number in order. .
Making a call from the other party ■ To have the other party make a call from a land-line phone or mobile phone in Japan to the terminal in the country you stay, the other party only needs to dial the phone number as in Japan.
Setting International dialing assist 1 2 From the Home screen, u . [Settings]u[Calls]u[Roaming settings]. 3 [International dial assist]. Auto Set whether to automatically add the conversion country code set in "Country code". Country code Select a country code used for auto conversion. Setting Network service (overseas) Set network service such as voice mail from overseas. ・ You need to set "Remote operation settings" (P.109) to "Activate Remote operation" in advance.
After returning to Japan After returning to Japan, restore to the settings which are made before you traveled. ■ When using packet communication overseas Turn off "Data roaming" (P.220). ■ If you cannot connect to DOCOMO network automatically after returning to Japan Set "Preferred network type" (P.221) to "5G/4G/3G/GSM". ・ Turn on "Automatically select network" (P.220).
Appendix Troubleshooting Troubleshooting When you have a vague idea of malfunctioning, you can perform diagnosis by yourself. For details, refer to NTT DOCOMO website. ・ Check if the software update is necessary for the terminal. If necessary, perform the software update (P.236). ・ When checking the following items not to improve the state, contact the phone number given in "Repairs (Inquiries/Request)" on the last page of this manual (in Japanese only) or a DOCOMO-specified repair office.
■ Charging Phenomenon Cause and handling Cannot charge ・ Check if the adapter's power (The notification plug is correctly inserted to a LED does not power outlet or accessory turn on, or the socket. ・ Check if the adapter and the icon does not indicate charging terminal are set correctly. → P.44 ・ When using an AC adapter status) (optional), check if the Type-C plug of the AC adapter is connected to the terminal correctly. → P.44 ・ When using the USB cable A to C 02 (optional), check if a PC is turned on.
■ Terminal operation Phenomenon Cause and handling ・ While calling, depending on the Become hot while operating/ radio wave condition or call charging duration time, the terminal may become hot around the earpiece/speaker. This condition is not abnormal. ・ While operating or charging, or if you use applications, record videos, etc. for a long time while charging the battery, the terminal, internal battery or adapter may become hot. It is not a problem for operation. You can continue to use the terminal.
Phenomenon Operations are not possible when tapping or pressing keys The screen reacts slowly when you tap or press the keys Cause and handling Check if the power is turned off. → P.47 ・ Check if you activate the screen lock. → P.197 When large amount of data is saved in the terminal or transferring large-size data between the terminal and microSD card, the reactions on the screen may be delayed.
Phenomenon Applications cannot be operated properly (applications cannot be activated, or errors occur frequently) ■ Cause and handling Are there any applications being disabled? Enable disabled applications, then retry. → P.185 ・ Are the permissions for the application granted? → P.61, P.183 ・ Phone call Phenomenon Cannot make a call even if you tap The ringtone does not sound Cause and handling Check if you activate Airplane mode. → P.180 Is "Ring and notification volume" set to the minimum? → P.
■ Display Phenomenon The display is dim ・ ・ ・ ・ ・ ■ Cause and handling Check if "Screen timeout" is set in short time period. → P.188 Check if the brightness of screen is changed. → P.189 When "Adaptive brightness" is ON, screen brightness is changed according to the ambient brightness. → P.188 Check if you cover the Proximity/ Light sensor with a sticker etc. → P.34 When the temperature of the terminal becomes high while using, the display may become darker. It is not abnormal.
■ International roaming Phenomenon Cannot use the terminal overseas (when is displayed) Cannot use the terminal overseas (when is displayed) Cause and handling Do you subscribe to WORLD WING? Check if you subscribe to WORLD WING. ・ Check if you are out of the international roaming service area or in an area with poor radio waves. Check if the service area and network operator are available or not, refer to NTT DOCOMO website. ・ Change the network settings or overseas network operator settings.
■ Bluetooth function Phenomenon The terminal cannot be connected to a Bluetooth device/A Bluetooth device cannot be found by search Cause and handling Allow Bluetooth device (commercially available) to be detectable and then make pairing with the device on the terminal. If you want to cancel a paired device and then make the pair setting again, cancel the pair settings on both the terminal and the Bluetooth device (commercially available). → P.
Error messages Error messages Cause and handling ・ The terminal is out of service No service area, or radio wave does not reach. Move to a location where radio wave can be reached. ・ The docomo nano UIM card is not working properly. Removing and inserting docomo nano UIM card may solve the problem. If the problem persists, contact "Repairs (Inquiries/Request)" on the last page of this manual (in Japanese only). Mobile network Install docomo nano UIM card not available correctly (P.
Software Update ・ Software Update Software update* is a function which updates the software so as to use the terminal safer and more comfortable. The followings are included. Be sure to update the software to the latest one. There are the following 4 types' updates for Software update. * On the terminal, it is displayed as System update.
Updating the software Starting the update To start updating, perform the either operation in the following. ・ From the update notification From the status bar of the terminal, tap the notification to start updating. ・ From the screen which appears on a regular basis When updating the terminal is available, the confirmation screen may appear. Select the operation in the confirmation screen to proceed with the update.
3 Notification of update completion. Notes When the update is complete, the completion screen appears on the terminal. ・ After the Android OS version upgrade, check if there are updates of the applications that you have installed personally. Without updating them, operations may become unstable or functions may not work properly. ・ Once the software update is complete, you cannot restore the previous software.
Software update is unavailable in the following cases. Solve the phenomenon and then retry. - During a call - When date and time are not set correctly - When the remaining battery is not sufficient - When the available memory is not sufficient in the internal storage - During International roaming ・ Do not turn off the terminal while updating the software. ・ Stay in a place with good radio wave condition when downloading the update file.
b Even if the warranty period has not expired, a fee will be charged for repair under the following circumstances. 1. The malfunction or damage is due to modification (including alteration of software) of the product. 2. The malfunction or damage is due to damage of the terminal body, display, external connection jack, etc. caused by being dropped or subjected to an external pressure, or the malfunction or damage is due to breakdown or deformation of the internal circuit board of the terminal. 3.
After Sales Services If you have problems with the terminal Before asking repair, see "Troubleshooting" (P.227) in this manual to check the problem. If the problem still persists, contact "Repairs (Inquiries/Request)" on the last page (in Japanese only). If repair is required resultingly Bring the terminal to the DOCOMO-specified repair office. However, it must be taken during business hours of the repair office. Note that repair may take some days depending on the problem.
● After the repair, Wi-Fi MAC address or Bluetooth address may be changed regardless of the repaired parts. ● Take care not to let an object that is easily affected by magnetism, such as a cash card near the terminal because the card may become unavailable. ● The terminal is waterproof. However, if inside of the terminal gets wet or moist, turn the power off and then bring the terminal to a DOCOMO-specified repair office as soon as possible.
Sharing screens with the operator (for inquiries on phone) 1 Call あんしん遠隔サポートセンター (Anshin Enkaku Support center). From DOCOMO mobile phones (No prefix) 15710 (toll free) From land-line phones 0120-783-360 Business hours: 9:00 a.m. to 8:00 p.m., open all year round ・ To make a call to the Anshin Enkaku Support center from the terminal, from the Home screen, [apps folder]u[ 遠隔 サポート (Enkaku support)]u[ 電話で問 い合わせる (Call for inquiries)]u . 2 From the Home screen, [apps folder]u[ 遠隔サポート (Enkaku support)].
Main specification Changes may occur because of software update, etc. For the latest information, refer to NTT DOCOMO website. ■ The terminal Product name Size Weight Display Size Type xxxxxx Height : Approx. 154 mm, Width : Approx. 68 mm, Thickness : Approx. 8.4 mm (Thickest part: Approx 9.1mm) Approx. 165 g Approx. 6.
Bluetooth Version Radio power Supported profile Codec*7 (version) Earphone- Diameter for microphone connector jack Number of pole*8 Camera Image Type pickup device Size 5.1*6 power class 1 HFP (1.7) (mSBC: 16kHz), HSP (1.2), OPP (1.2), SPP (1.2), HID (1.0), A2DP (1.3) (LDAC/aptX Adaptive/aptX HD/aptX/ AAC/SBC), AVRCP (1.6), PBAP (1.2), PAN (PAN-NAP (1.0)/ PANU (1.0)), HOGP (1.0), MAP (1.4) Effective pixels 3.
Zoom Video (digital × optical) Still image Continuous 1seg watching time*11 Continuous Full seg watching time*11 Answering Savable Machine number Maximum recordable time per one Camera : Up to approx. 9.0 x Front camera : ― Camera : Up to approx. 9.0 x Front camera : ― Approx.740 min. Approx.810 min. No limit*12 Up to 60 sec. *6 However, procedures may differ or data transfer may not be possible depending on the Bluetooth device's characteristics or specifications.
■ File format (media) ■ The terminal supports the display or playback of the following file formats: Type Sound Still image Video File format AAC-LC (.mp4, .m4v, .3gp, .3gpp, .3g2, .3gpp2, .ts, .aac, .m4a), AAC+ (.mp4, .3gp, .3gpp, .3g2, .3gpp2, .ts, .aac), eAAC+ (.mp4, .3gp, .3gpp, .3g2, .3gpp2, .ts, .aac), AAC-ELD (.mp4, .3gp, .3gpp, .3g2, .3gpp2), AMR-NB (.3gp, .3gpp, .3g2, .3gpp2, .amr), AMR-WB (.3gp, .3gpp, .3g2, .3gpp2, .awb), FLAC (.flac), MP3 (.mp3), MIDI (.mid, .midi, .smf, .xmf, .mxmf, .
Certificate and compliance You can check details of certificate and compliance mark specific to the terminal (including certificate number/compliance number). 1 2 ■ From the Home screen, [apps folder]u[Settings]u[About phone]. [Certificates] VCCI The terminal complies with a technical standards based on VCCI RULES FOR VOLUNTARY CONTROL MEASURES and the mark of conformity is depicted electronically on the screen.
Sony Mobile and its third party suppliers and licensors retain all rights, title and interest in and to the Software. To the extent that the Software contains material or code of a third party, such third parties shall be beneficiaries of these terms. This license is governed by the laws of Japan. When applicable, the foregoing applies to statutory consumer rights.
Intellectual Property Right About the Copyright and Portrait rights Copyrighted contents you recorded or obtained from sites or Internet home pages using this product by downloading or other means, such as documents, images, music data, software, are prohibited from reproduction, transformation and transmission over public lines without consent of the copyright holders, unless intended for personal use or any other purpose permitted by law.
"Catch Phone (Call waiting service)" is a registered trademark of Nippon Telegraph and Telephone Corporation. ・ PlayStation and DUALSHOCK are trademarks or registered trademarks or Sony Interactive Entertainment Inc. ・ Sony, Xperia, FeliCa, Reader, DSEE Ultimate, STAMINA, and the Video & TV SideView logo are trademarks or registered trademarks of Sony Corporation. ・ microSD logo, microSDHC logo and microSDXC logo are trademarks of SD-3C, LLC. ・ USB Type-C™ is a trademark of USB Implementers Forum.
"Microsoft Word" is a product name of Microsoft Corporation in the United States. ・ Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. ・ This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. ・ QR code is a registered trademark of Denso Wave Inc.
SIM unlock This terminal supports SIM unlock. If you release SIM lock, you can use SIM by a carrier other than NTT DOCOMO. ・ Available services and functions may be limited. DOCOMO is not liable to any failures or malfunctions. ・ For details of SIM unlock procedure, refer to NTT DOCOMO website. 1 2 3 Insert SIM card provided by other company. Power on the terminal. Enter the SIM unlock codeu [UNLOCK].
Index A About phone ・・・・・・・・・・・・・・・・・・・・・・・・ 210 Access point Initializing ・・・・・・・・・・・・・・・・・・・・・・・・・ 177 Setting・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 176 Accessibility ・・・・・・・・・・・・・・・・・・・・・・・・・ 203 Accounts ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 202 Add account ・・・・・・・・・・・・・・・・・・・・・・・・・ 202 Adjusting sound volume ・・・・・・・・・・・・・・・ 193 Airplane mode ・・・・・・・・・・・・・・・・・・・・・・・ 180 Alarm ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 166 Alarm ringtone ・・・・・・・・・・・・・・・・・・・・・・・ 194 Alarm volume ・・・・・・・・・・・・・・・・・・・・・・・・ 193 Amazon Kindle ・・・・・・・・・・・・・
Ending ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 105 Hold call ・・・・・・・・・・・・・・・・・・・・・・・・・・ 105 Incoming screen ・・・・・・・・・・・・・・・・・・・・ 103 Making a call ・・・・・・・・・・・・・・・・・・・・・・・ 100 Mute ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 105 Receiving ・・・・・・・・・・・・・・・・・・・・・・・・・ 103 Speaker ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 105 Call Blocking ・・・・・・・・・・・・・・・・・・・・・・・・・ 109 Call forwarding service ・・・・・・・・・・・・・・・・・ 108 Call history ・・・・・・・・・・・・・・・・・・・・・・・・・・ 106 Adding to the phonebook ・・・・・・・・・・・・ 106 Deleting ・・・・・・・・・・・・・・・・・・・・・・・・・・ 107 Call History s
dmenu ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 148 docomo Data Copy・・・・・・・・・・・・・・・・・・・・ 168 docomo mail ・・・・・・・・・・・・・・・・・・・・・・・・・ 118 docomo nano UIM card ・・・・・・・・・・・・・・・・・ 36 Precautions ・・・・・・・・・・・・・・・・・・・・・・・・・ 23 docomo service/cloud ・・・・・・・・・・・・・・・・・ 201 Docs ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 95 dphoto ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 97 Drive ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 95 Duo ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 97 Dynamic Vibration ・・・・・・・・・・・・・・・・・・・・ 192 E Early Warning "Area Mail"・・・・・・・・・・・・・・・ 125 Emerge
Wallpaper (docomo LIVE UX) ・・・・・・・・・・・ Wallpaper (Xperia Home) ・・・・・・・・・・・・・・ Widget (docomo LIVE UX) ・・・・・・・・・・・・・ Widget (Xperia Home) ・・・・・・・・・・・・・・・・ Xperia Home ・・・・・・・・・・・・・・・・・・・・・・・・ Home Settings (Xperia Home) ・・・・・・・・・・・・ 80 87 80 86 85 87 I iD application ・・・・・・・・・・・・・・・・・・・・・・・・ 153 Imaging Edge Mobile ・・・・・・・・・・・・・・・・・・・ 98 In-call volume Setting・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 193 Initial settings ・・・・・・・・・・・・・・・・・・・・・・・・・ 48 International call Making a call from Japan ・・・・・・・・・・・・・ 102 Making a
Notification panel ・・・・・・・・・・・・・・・・・・・・・・ 71 Notification sound ・・・・・・・・・・・・・・・・・・・・ 194 Notification volume ・・・・・・・・・・・・・・・・・・・ 193 Nuisance call blocking service ・・・・・・・・・・・ 108 O One-handed mode ・・・・・・・・・・・・・・・・・・・・・ 75 Osaifu-Keitai ・・・・・・・・・・・・・・・・・・・・・・・・・ 150 Lock ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 152 Osaifu-Keitai compatible service ・・・・・・・ 152 Settings ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 151 Osusume Apps ・・・・・・・・・・・・・・・・・・・・・・・・ 81 P Personal dictionary・・・・・・・・・・・・・・・・・・・・・ 67 Phone Ringtone volume ・・・・・・・・
Security code Network security code ・・・・・・・・・・・・・・・・ 51 PIN code ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 51 PIN Unlock Key (PUK code) ・・・・・・・・・・・・ 52 Setting menu ・・・・・・・・・・・・・・・・・・・・・・・・ 171 Sheets ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 94 Shooting photos ・・・・・・・・・・・・・・・・・・・・・・ 135 Shooting videos ・・・・・・・・・・・・・・・・・・・・・・ 137 Side sense ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 54 Multi-window menu・・・・・・・・・・・・・・・・・・ 57 Setting・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 191 Side sense menu・・・・・・・・・・・・・・・・・・・・・ 56 Silent mode・・・・・・・・・・・・・・・・・・・・・・・・・・・ 58
V Symbols Vibrate Settings ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 193 Vibration Silent mode・・・・・・・・・・・・・・・・・・・・・・・・・ 59 Video & TV SideView ・・・・・・・・・・・・・・・・・・・ 99 Voice search ・・・・・・・・・・・・・・・・・・・・・・・・・・ 76 Voicemail service ・・・・・・・・・・・・・・・・・・・・・ 108 VPN ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 180 +Message ・・・・・・・・・・・・・・・・・・・・・・・・・・・ Deleting a message ・・・・・・・・・・・・・・・・・ Deleting a thread ・・・・・・・・・・・・・・・・・・・ Forwarding ・・・・・・・・・・・・・・・・・・・・・・・・ Official Account ・・・・・・・・・・・・・・・・・・・・ Receiving ・・・・・・・・・・・・・・・・・・・・・・・・・ Sending
Check usage charge, usage status, subscription information, or make various application online The terminal: d メニュー (dmenu) u [My docomo(お客様サポート)(My docomo (Customer support))] PC: My docomo (https://www.nttdocomo.co.jp/mydocomo/ ) (in Japanese only) * There are cases where the site may not be available due to system maintenance, etc. * To use "My docomo", "Network security code" and "ID/password of d ACCOUNT" are required. Don't forget your mobile phone ...
General Inquiries 0120-005-250 (toll free) *Service available in: English, Portuguese, Chinese, Spanish. *Unavailable from part of IP phones. (Business hours: 9:00 a.m. to 8:00 p.m.) Repairs (Inquiries/Request) ■From DOCOMO mobile phones (In Japanese only) (No prefix) 113 (toll free) *Unavailable from land-line phones, etc.