User Guide

ManualsBrandsSony Mobile Communications ManualsElectronicsGSM/WCDMA/LTE Phone+Bluetooth, DTS/UNII a/b/g/n and NFC

Before Using the Terminal

docomo nano UIM card/microSD card slot

Notification LED

→

P. 4 7

Front camera lens

Earpiece/speaker

Proximity/light sensor : Detects a face getting closer

to the touch screen during a call and turns it off to

prevent misoperation, and helps with automatic

screen brightness control.

Touch screen

→

P. 4 2

Speaker

Volume key/Zoom key

i O

Power key/Screen lock key/Fingerprint sensor

→

P. 3 9 , P. 1 7 5

j k

Camera key

→

P.129, P.132, P.134

Camera lens

RGBC-IR sensor : When shooting, it detects

elements of light source of shooting environment

to adjust white balance automatically.

Flash/Photo light

LTE/FOMA antenna section

LTE/Wi-Fi antenna section

Laser AF sensor : When shooting, it detects distance

to a subject and focus on automatically.

Wi-Fi/Bluetooth antenna section

Nameplate

LTE antenna section

mark

LTE/Wi-Fi antenna section

Headset jack

→

P.123, P.226

Part names and functions

b c d e

x y

k l m

Top

Bottom

RightLeft BackFront

Summary of content (11 pages)

PAGE 1
Part names and functions b c d e k l m o n v q w Top x y p h a r f Bottom i s t j u g Left a b c d e Front Right docomo nano UIM card/microSD card slot Notification LED → P.47 Front camera lens Earpiece/speaker Proximity/light sensor : Detects a face getting closer to the touch screen during a call and turns it off to prevent misoperation, and helps with automatic screen brightness control. f Touch screen → P.
PAGE 2
w Second microphone : Reduces noise to make voice to be listened easily. x Microphone y USB Type-C jack *1 The antenna is built into the terminal. Covering around the antenna with your hand may affect the quality of communications. *2 A sticker bearing the CE mark, FCC ID, IMEI information, etc. is attached. Please do not peel off the sticker or remove the nameplate. ❖Note Do not put a sticker or other material on the proximity/light sensor, laser AF sensor, or RGBC-IR sensor.
PAGE 3
2 Pull the tray straight out from the terminal. 4 Turn the terminal horizontally and insert the tray with the card and press it straight into the slot. ･ 3 Be careful about the direction to insert of the tray. With the IC side facing up, place the docomo nano UIM card on the tray. Make sure that the cut corner of the card is oriented properly. ･ Be sure to fit the docomo nano UIM card into the tray so that it does not shift.
PAGE 4
Removing docomo nano UIM card 1 2 5 Remove the cover of docomo nano UIM card/microSD card slot (P.26). Pull the tray straight out from the terminal. (P.32). 3 Remove the docomo nano UIM card from the tray. 4 Insert the tray into the terminal and press it straight into the slot. ･ Firmly press until the tray is all the way in, and make sure that there are no gaps between the terminal and cover (P.32).
PAGE 5
Life of the internal battery Charging The internal battery is not fully charged at the time of purchase. ･ Estimated charging time (P.224) Operation time on full charge (estimate) The charging time varies by the internal battery condition or operating environment. ･ "Continuous standby time", "Continuous call time" (P.226) Continuous FOMA/3G stand-by time GSM LTE Continuous FOMA/3G call time GSM VoLTE call (voice) Stationary (Auto) : Approx. 650 hours Stationary (Auto) : Approx.
PAGE 6
Use a compatible AC adapter or USB cable A to C for charging. If you use a charger other than compatible ones, charging may not be available or operations may not be performed correctly. ･ Insert and remove the AC adapter cord or USB cable A to C slowly and evenly so that excessive force is not applied. ･ When charging starts while the power is on, a sound to indicate the start of charging is heard, and the notification LED of the terminal turns on (P.47).
PAGE 7
If regularity in your charging habit cannot be found, Battery Care does not start because incomplete of the learning and normal charging will be performed. ･ If you remove charging equipment during Battery Care charging, the terminal may not be fully charged. ･ 2 Unfold the power plug of the AC adapter and insert it into a power outlet. Then place the terminal on the desktop holder.
PAGE 8
❖Note Connect the terminal correctly. Wrong connection may cause damage. ･ A terminal mounted on the desktop holder may be damaged if pressed hard against the holder. ･ Attaching/Removing the attachment ■ 1 Attaching Check the shape of front/back of the attachment and the attaching part of the desktop holder, then fit the attachment with the desktop holder. 2 Firmly press the attachment straight into place and make sure that there are no gaps between the attachment and the desktop holder.
PAGE 9
3 When charging is complete, remove the power plug of the AC adapter, and then remove the Type-C plug horizontally from the terminal. 2 Insert a USB plug of the USB cable A to C to a USB port of a PC. ･ A sound to indicate the start of charging is heard, and the notification LED of the terminal turns on (P.47). ❖Note Connect the AC adapter correctly. Wrong connection may cause damage.
PAGE 10
3 When charging is complete, remove the USB plug of the USB cable A to C from the USB port of PC and then remove the Type-C plug horizontally from the terminal. Turning power on/off Turning power on 1 ❖Note ･ Press and hold O for at least 1 second. The terminal vibrates and the lock screen appears after a while. ･ When you first turn on the power and " ようこそ (Welcome)" is displayed, follow the onscreen instructions to make initial settings (P.41). ･ Connect the USB cable A to C correctly.
PAGE 11
When SIM card lock (P.175) is set, enter PIN code on the PIN code entry screen (P.175). ･ ❖Information Also, when the screen backlight goes off after a specified time elapses, the terminal goes into sleep mode. You can change the time-out period for turning off the screen backlight (P.164). ･ Turning power off 1 Press and hold O for at least 1 second. 2 [Power off].