Reference Guide

SRS-XB13 UC (US/CaFR/LaES) 5-025-467-11(1)
5-025-467-11(1)
©2021 Sony Corporation
Printed in China / Imprimé en Chine
https://www.sony.net/
SRS-XB13
Wireless Speaker
Enceinte sans fil
Altavoz inalámbrico
Reference Guide
Guide de référence
Guía de referencia
Supplier's Declaration of Conformity
Trade Name : SONY
Model : SRS-XB13
Responsible Party : Sony Electronics Inc.
Address : 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
Telephone Number : 858-942-2230
This device complies with part 15 of FCC Rules and Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The available scientific evidence does not show that any health
problems are associated with using low power wireless devices. There is
no proof, however, that these low power wireless devices are absolutely
safe. Low power Wireless devices emit low levels of radio frequency
energy (RF) in the microwave range while being used. Whereas high
levels of RF can produce health effects (by heating tissue), exposure of
low-level RF that does not produce heating effects causes no known
adverse health effects. Many studies of low-level RF exposures have not
found any biological effects. Some studies have suggested that some
biological effects might occur, but such findings have not been
confirmed by additional research. The model has been tested and found
to comply with FCC/ISED radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS-102 of the ISED radio frequency (RF)
Exposure rules.
Caution on charging
Inserting the USB plug while it is wet may cause a short circuit due
to foreign matter or liquid (tap water, salt water, soft drinks, etc.)
getting on the main unit or charging cable. This may cause
malfunctions or abnormal overheating.
Never insert the USB plug while the main unit or
charging cable is wet.
Precautions
On safety
• Important information such as the model name is located on the
bottom of the unit.
On placement
• To eliminate the risk of malfunctions, avoid the following locations
when placing or leaving this unit.
– A place subject to high temperatures, such as under direct sunlight or
lighting equipment, near a heat source, or in a sauna
– Inside a vehicle with the windows closed (especially in summertime)
– A place subject to excessive dust
– A place subject to strong vibration
• Place this unit on a flat, level surface. When placed on a sloped surface,
the unit may fall over or fall off the surface due to its own vibration,
resulting in injuries, malfunctions, or performance degradation.
• Depending on the conditions where this unit is placed, it may fall over
or fall off the surface. Do not leave any valuables near the unit.
• This unit is not anti-magnetic. Keep objects susceptible to magnetism
(recorded tapes, watches, cash cards and credit cards with magnetic
coding, etc.) away from the unit. When you carry around the unit, keep
this in mind as well.
Others
• Do not use or leave the unit in an extremely cold or hot environment
(temperature outside the range of 5 °C – 35 °C (41 °F – 95 °F)). If the unit
is used or left in outside the above range, the unit may automatically
stop to protect internal circuitry.
• At high temperature, the charging may stop or the volume may reduce
to protect the battery.
• Even if you do not intend to use the unit for a long time, charge the
battery to its full capacity once every 6 months to maintain its
performance.
On Copyrights
• Android is a trademark of GoogleLLC.
• The BLUETOOTH® word mark and logos are registered trademarks
owned by BluetoothSIG,Inc. and any use of such marks by
SonyCorporation is under license.
• iPhone, iPod and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
• USB Type-C® and USB-C® are registered trademarks of USB
Implementers Forum.
• Other trademarks and trade names are those of their respective
owners.
• ™ and ® marks are omitted in the documents.
Notes on waterproof and Dustproof
features (Read before using the unit)
Waterproof and Dustproof performance of the unit
The unit, with the cap fastened securely, has a waterproof specification
of IPX7*
1
as specified in “Degree of protection against water immersion”
of the IEC60529 “Ingress Protection Rating (IP Code)”*
3
, and a Dustproof
specification of IP6X*
2
as specified in “Degrees of protection against
solid foreign objects”*
3
.
Liquids that the waterproof performance specifications
apply to
Applicable fresh water, tap water, pool water
Not applicable liquids other than the above (soapy water, water
with detergent or bath agents, shampoo, hot spring
water, salt water, etc.)
*
1
IPX7 (Degree of protection against water immersion): For details, refer
to the Help Guide.
*
2
IP6X (Degrees of protection against dust): For details, refer to the Help
Guide.
*
3
The supplied accessories and the connectors of this unit (USB) are
neither waterproof nor Dustproof. To reduce the risk of fire or electric
shocks, do not expose the unit to water or droplets while using either
or both of the connectors (USB). Do not place a vase or any other
liquid-filled container on the unit.
The waterproof and Dustproof performance of the unit is based on our
measurements under the conditions herein described. Note that
malfunctions as a result of water immersion or dust intrusion caused
by misuse by the customer are not covered by the warranty.
To avoid the deterioration of waterproof and Dustproof
performance
Check the following and use the unit correctly.
• This unit does not have a design that is resistant to water pressure. Use
of the unit in a location where high water pressure is applied, such as
in the shower, may cause a malfunction.
• Do not pour high-temperature water or blow hot air from a hair dryer
or any other appliance on the unit directly. Also never use the unit in a
place subject to high temperatures, such as in a sauna or near a heat
source.
• Handle the cap with care. The cap plays a very important role in
maintenance of the waterproof and Dustproof performance. When
using the unit, make sure that the cap is closed completely. When
closing the cap, be careful not to allow foreign objects inside. If the cap
is not closed completely the waterproof and Dustproof performance
may deteriorate and may cause a malfunction of the unit as a result of
water or dust particles entering the unit.
Cap
How to care for the unit
You can use the unit more comfortably and for a longer period of time
by following the maintenance procedure below.
• If the surface of the unit gets dirty in the following cases, wash the unit
with fresh water (tap water, etc.) promptly to remove the dirt. Leaving
dirt on its surface may cause the surface to discolor or deteriorate, or
the unit to malfunction.
Ex.
– When the unit has sand, salt (chlorine), or other residue on it after
having been used in a mountain area, by a swimming pool, etc.
– When the unit is stained with foreign substances (sunscreen, suntan
oil, etc.)
• If the unit gets wet, wipe off the moisture using a dry soft cloth
immediately. In addition, dry the unit in an airy place until no moisture
remains.
• The sound quality may change if water enters the speaker component
of the unit. This, however, does not indicate a malfunction. Wipe the
moisture off the unit surface, and leave the unit on a dry soft cloth with
its surface with the speaker component facing down to let the water
out from inside the unit. Then, dry the unit in an airy place until no
moisture remains.
Note
• If the surface of the unit gets dirty, do not use detergent, thinner,
benzine, alcohol, etc. to clean the unit because it will affect the water
repellent function of the unit.
• Especially in cold regions, be sure to wipe off the moisture after using
the unit. Leaving moisture on its surface may cause the unit to freeze
and malfunction.
Notes on the License
This product contains software that Sony uses under a licensing
agreement with the owner of its copyright. We are obligated to
announce the contents of the agreement to customers under
requirement by the owner of copyright for the software. Please
access the following URL and read the contents of the license.
URL: @@@
Disclaimer regarding services offered by third parties
Services offered by third parties may be changed, suspended, or
terminated without prior notice. Sony does not bear any
responsibility in these sorts of situations.
Specifications
Speaker section
Speaker system Approx. XXmm (XXin) dia. × 1
Enclosure type Passive radiator model
BLUETOOTH
Communication System
BLUETOOTH Specification version X.X
Maximum communication range
Line of sight approx. XXm (XXft)*
1
Frequency band 2.4GHz band (2.4000GHz - 2.4835GHz)
Modulation method
FHSS
Compatible BLUETOOTH Profiles*
2
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HSP (Headset Profile)
HFP (Hands-free Profile)
Supported Codec*
3
SBC (Subband Codec)
AAC (Advanced Audio Coding)
Transmission range (A2DP)
20Hz - 20000Hz (Sampling frequency 44.1kHz)
*
1
The actual range will vary depending on factors such as obstacles
between devices, magnetic fields around a microwave oven, static
electricity, reception sensitivity, antenna’s performance, operating
system, software application, etc.
*
2
BLUETOOTH standard profiles indicate the purpose of BLUETOOTH
communications between devices.
*
3
Codec: Audio signal compression and conversion format
Note
Depending on the network environment, there may be an interruption at
the high bitrate transmission.
Microphone
Type Electret condenser
Directional characteristic
Omni directional
Effective frequency range
100Hz - 7000Hz
Amplifier section
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
With X  loads, both channels driven, from XXXHz
- XXXXXHz; rated X.X W per channel minimum RMS
power at stereo mode, with no more than X% total
harmonic distortion from 250 mW to rated output.
General
Power DC 5 V 500 mA (using the USB power supply) or using
built-in lithium-ion battery
Lithium-ion battery life (with playback via a BLUETOOTH connection)
Approx. XXhours*
4
*
5
Approx. XX hours*
4
*
6
Dimensions (including projecting parts and controls)
Approx. XXmm (Xin) dia. × XXmm (Xin) (H)
Mass Approx. XXXg (Xoz) including battery
Supplied accessory
USB Type-C cable (USB-A to USB-C)*
7
(1),
Strap (1) (attached to the unit)
*
4
Actual performance time may vary from the listed time due to the
volume, songs played, surrounding temperature, and usage
conditions.
*
5
Measured value acquired by playing our specified music source with
the volume level of the unit set to XX.
*
6
Measured value acquired by playing our specified music source with
the volume level of the unit set to the maximum.
*
7
A charging cable exclusively designed for the unit. Do not use the
cable for any other purposes.
System requirements for charging battery using USB
Using a USB power supply capable of feeding in DC5V 0.5A.
Do not use a USB adaptor that exceeds the maximum output of 13 W
(5 V, 2.6 A).
Design and specifications are subject to change without notice.
Français Enceinte sans fil
Avant d’utiliser l’appareil, veuillez lire attentivement ce guide et le
conserver pour référence ultérieure.
Informations à noter par le propriétaire
Le numéro de série est apposé sur la partie inférieure du produit.
Notez ce numéro dans l’espace réservé ci-dessous. Veuillez le
mentionner chaque fois que vous appelez votre distributeur Sony à
propos de ce produit.
Numéro de modèle SRS-XB13
Numéro de série
PRÉCAUTION
Pour les clients aux États-Unis
Veuillez noter que tout changement ou toute modification qui n’est pas
expressément approuvé(e) dans ce manuel peut annuler votre capacité
à utiliser cet appareil.
REMARQUE :
Cet équipement a été testé et déclaré conforme aux normes relatives au
matériel numérique de la classe B, fixées par l’article 15 des règlements
de la FCC. Ces limites sont destinées à assurer une protection suffisante
contre les interférences dans une installation résidentielle. Cet
équipement génère et utilise des fréquences radio qui, en cas
d’installation et d’utilisation incorrectes, peuvent être à l’origine
d’interférences dans la réception radio et télévision. Toutefois, rien ne
garantit qu’il n’y aura pas d’interférences. Si des interférences se
produisent, il est possible de déterminer si elles sont dues au matériel
en éteignant et en rallumant l’appareil, et si c’est le cas, l’utilisateur est
invité à corriger le problème de l’une des manières suivantes :
– Modifier l’orientation ou l’emplacement de l’antenne réceptrice.
– Eloigner l’appareil du de réception.
– Brancher l’appareil sur une prise située sur un circuit différent de celui
du récepteur.
– Consulter le revendeur ou un technicien radio/TV expérimenté pour
obtenir une assistance.
Cet appareil ne doit pas se trouver à proximité d’un autre émetteur ou
d’une autre antenne, ou encore être utilisé en même temps que ceux-ci.
Si vous avez des questions concernant ce produit :
Site internet : https://www.sony.com/support
Téléphone : Centre d’assistance à la clientèle Sony au 1 800 222 7669
Courrier postal : Sony Customer Information Service Center 12451
Gateway Blvd., Fort Myers, FL 33913
Déclaration de conformité du fournisseur
Nom commercial : SONY
Modèle : SRS-XB13
Responsable : Sony Electronics Inc.
Adresse : 16535 Via Esprillo, San Diego, CA 92127 É.-U.A.
Numéro de téléphone : 858 942 2230
Le présent appareil est conforme à la partie 15 des règles de la FCC et
aux normes des CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout
brouillage subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
Les connaissances scientifiques dont nous disposons n’ont mis en
évidence aucun problème de santé associé à l’usage des appareils sans
fil à faible puissance. Nous ne sommes cependant pas en mesure de
prouver que ces appareils sans fil à faible puissance sont entièrement
sans danger. Les appareils sans fil à faible puissance émettent une
énergie fréquence radioélectrique (RF) très faible dans le spectre des
micro-ondes lorsqu’ils sont utilisés. Alors qu’une dose élevée de RF peut
avoir des effets sur la santé (en chauffant les tissus), l’exposition à de
faibles RF qui ne produisent pas de chaleur n’a pas de mauvais effets
connus sur la santé. De nombreuses études ont été menées sur les
expositions aux RF faibles et n’ont découvert aucun effet biologique.
Certaines études ont suggéré qu’il pouvait y avoir certains effets
biologiques, mais ces résultats n’ont pas été confirmés par des
recherches supplémentaires. Ce modèle a été testé et jugé conforme
aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques
(RF) de la FCC lignes directrices d’exposition et d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’ ISDE.
English Wireless Speaker
Before operating the unit, please read this guide thoroughly and retain it
for future reference.
Owner’s Record
The serial number is located on the bottom of the product.
Record the serial number in the space provided below. Refer to them
whenever you call upon your Sony dealer regarding this product.
Model No. SRS-XB13
Serial No.
CAUTION
Do not install the appliance in a confined space, such as a bookcase or
built-in cabinet.
Do not expose the batteries (battery pack or batteries installed) to
excessive heat such as sunshine, fire or the like for a long time. Do not
expose the batteries to extreme low temperature conditions that may
result in overheating and thermal runaway. Do not dismantle, open or
shred secondary cells or batteries. In the event of a cell leaking, do not
allow the liquid to come in contact with the skin or eyes. If contact has
been made, wash the affected area with copious amounts of water and
seek medical advice. Secondary cells and batteries need to be charged
before use. Always use the correct charger and refer to the
manufacturer’s instructions or equipment manual for proper charging
instructions. After extended periods of storage, it may be necessary to
charge and discharge the cells or batteries several times to obtain
maximum performance. Dispose of properly.
RECYCLING RECHARGEABLE BATTERIES
Rechargeable batteries are recyclable.
You can help preserve our environment by returning your used
rechargeable batteries to the collection and recycling location nearest
you.
For more information regarding recycling of rechargeable batteries, visit
https://www.sony.com/electronics/eco/environmental-management
Caution: Do not handle damaged or leaking rechargeable batteries.
Do not place this product close to medical devices
This product (including accessories) has magnet(s) which may interfere
with pacemakers, programmable shunt valves for hydrocephalus
treatment, or other medical devices. Do not place this product close to
persons who use such medical devices. Consult your doctor before using
this product if you use any such medical device.
For customers in the USA
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment must not be co-located or operated in conjunction with
any other antenna or transmitter.
If you have any questions about this product:
Visit: https://www.sony.com/support
Contact: Sony Customer Information Service Center at 1-800-222-7669
Write: Sony Customer Information Service Center 12451 Gateway Blvd.,
Fort Myers, FL 33913
秘｜
CONFIDENTIAL