Phonak RemoteControl User Guide
Welcome Congratulations on choosing the Phonak RemoteControl. Please read the user guide carefully to make sure that you understand and get the best out of your remote control. For more information about features and benefits, simply contact your hearing care professional. ! Compatibility information: Check your hearing aid compatibility with your hearing care professional. Phonak – life is on www.phonak.
Content 1. 2. 2.1 2.2 2.3 2.4 Description Using phonak RemoteControl Activating the Phonak RemoteControl Switching On/Off Understanding the indicator light Pairing the Phonak RemoteControl with your hearing aid 2.5 Changing hearing aid volume 2.6 Changing hearing aid program 3. Inserting a new battery 3.1. Open the battery compartment 3.2. Remove the battery from the battery compartment 3.3. Insert the new battery 3.4. Close the battery compartment 4. Reset the Phonak RemoteControl 5.
1. Description 2. Using Phonak RemoteControl The intended user of the Phonak RemoteControl is to enable changes of your hearing aid programs and volume. 2.1 Activating the Phonak RemoteControl Pull out the battery protective tab to activate your Phonak RemoteControl. Light indicator Volume up On/Off slider 2.2 Switching On/Off Use the slider to switch on or off. Battery door 2.
2.4 Pairing the Phonak RemoteControl with your hearing aid To use your Phonak RemoteControl with your hearing aids, you must first pair the hearing aids. It is only necessary to perform the pairing procedure once with your hearing aids. After the initial pairing, your Phonak RemoteControl will connect automatically with your hearing aids. The Phonak RemoteControl will be automatically in the pairing mode if switched on for the first time.
3. Inserting a new battery 2.6 Changing hearing aid program 3.1. Open the battery compartment Each press of the program button will switch your hearing aids to the next available program. 1 2 Press to change the hearing aid program 3.2. Remove the battery from the battery compartment Hearing aids may beep to confirm selection, depending on your hearing aid configuration. Changes are applied to both hearing aids at the same time. 3.3.
4. Reset the Phonak RemoteControl The Phonak RemoteControl requires a lithium button cell (CR2032) 3.4. Close the battery compartment 12 A reset of your Phonak RemoteControl will remove the pairing to your hearing aids. Press the volume up “+” button and the program change button for more than 10 seconds.
5. Troubleshooting Problem No indicator light when a button is pressed Hearing aids do not respond to the RemoteControl commands Solid red light indicator Causes Remote control is switched off Batter is empty Hearing aids are switched off Hearing aids are not paired with your RemoteControl Remote control is switched off Battery is empty General device error What to do Switch on your remote control (chapter 2.
6. Compliance information Declaration of conformity Hereby Phonak AG declares that this Phonak product is in compliance with the essential requirements of the Medical Devices Directive 93/42/EEC as well as the Radio Equipment Directive 2014 / 53 / EU. The full text of the declaration of conformity can be obtained from the manufacturer or the local Phonak representative whose address can be taken from the list on http:// www.phonak.com (worldwide locations).
Notice 3: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Compliance with emission and immunity standards Emission standards 20 EN 60601–1-2:2015 IEC 60601–1-2:2014 EN 55011:2009+A1 CISPR11:2009/AMD1:2010 CISPR22:1997 CISPR32:2012 ISO 7637-2:2011 CISPR25:2016 EN 55025:2017 Immunity standards EN 60601-1-2:2015 IEC 60601-1-2:2014 EN 61000-4-2:2009 IEC 61000-4-2:2008 EN 61000-4-3:2006+A1+A2 IEC 61000-4-3:2006+A1+A2 EN 61000-4-4:2012 IEC 61000-4-4:2012 EN 61000-4-5:2014 IEC 61000-4-5:2014 EN 61000-4-6:2014 IEC 61000-4-6:2013 EN 61000-4-8:2010 IEC 61000-4-8:2009 EN
7. Information and description of symbols With the CE symbol, Sonova AG confirms that this product – including accessories – meets the requirements of the Medical Devices Directive 93/42/EEC as well as the Radio Equipment Directive 2014/53/EU. The numbers after the CE symbol correspond to the code of certified institutions that were consulted under the above-mentioned directives.
Japanese mark for certified radio equipment. Humidity during storage: 0% to 70%, if not in use. Indicates the manufacturer’s serial number so that a specific medical device can be identified. Atmospheric pressure during transportation and storage: 200 hPA to 1500 hPa Indicates the manufacturer’s catalogue number so that the medical device can be identified. During transportation keep dry.
8. Important safety information Please read the information on the following pages before using your device 8.1 Hazard warnings Your device operate between 2.4 GHz–2.48 GHz frequency range. When flying please check if flight operator requires devices to be switched off. The intended use of the remote control is to enable changes of the hearing aid programs and volume. Keep this device out of reach of children and mentally challenged people or pets.
Remove the battery if you are not using the device for a long period of time. Dispose of electrical components in accordance with your local regulations by Sonova AG. External devices may only be connected if they have been tested in accordance with corresponding IECXXXXX standards. Do not use the device in explosive areas (flammable anesthetics, mines or industrial areas with a danger of explosions), oxygen rich environments or where electronic equipment is prohibited. 8.
Clean the device using a damp cloth. Never use household cleaning products (washing powder, soap, etc.) or alcohol to clean the device. Never use a microwave or other heating devices to dry the device. The digitally-coded, transmission technology used in the device is highly reliable and experiences virtually no interference from other devices.
9. Service and warranty 9.1 Local warranty Please ask the hearing care professional, where you purchased your devices, about the terms of the local warranty. 9.2 International warranty Sonova offers a one year limited international warranty, valid as of the date of purchase. This limited warranty covers manufacturing and material defects. The warranty is valid only if proof of purchase is shown. 9.
029-0782-02/V1.00/2019-02/na © 2019 Sonova AG All rights reserved 288407 613389 Manufacturer: Sonova AG Laubisrütistrasse 28 CH-8712 Stäfa Switzerland www.phonak.