Product External Specifications For 802.11b/g /n MIMO Mini-PCI Card (Atheros Solution) WMP-N06 Revision: 1.
FCC Statement : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, and similar equipment).
1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11b/g MIMOMini-PCI Card. This Mini-PCI Card is based on Atheros AR5008 chipset that complied with IEEE 802.11n draft 1.0 standard from 2.4~2.5GHz, and it can be used to provide up to 11Mbps for IEEE 802.11b and 54Mbps/108Mbps for 2.4GHz IEEE 802.11g to connect your wireless LAN. With seamless roaming, fully interoperability and advanced security with WEP standard, 802.
2.2 General Requirements 2.2.1 IEEE 802.11b Section # Feature Detailed Description 2.2.1.1 2.2.1.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK 2400 ~ 2497MHz ISM band Data Rate Media Access Protocol Transmitter Output Power 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK 2.2.1.3 2.2.1.4 2.2.1.5 2.2.1.6 2.2.1.7 2.2.1.
# Feature Detailed Description –70dBm at 54Mbps 2.2.3 IEEE 802.11n Section # Feature Detailed Description 2.2.3.1 2.2.3.2 Standard Radio and Modulation Type Operating Frequency Channel Numbers IEEE 802.11n draft 1.0 BPSK, QPSK, 16QAM, 64QAM with OFDM Data Rate Media Access Protocol Transmitter Output Power 2400 ~ 2483.
2.2.4.
2.3 Software Requirements The Configuration Software supports Microsoft Windows 98SE, ME, 2000, and XP. This configuration software includes the following functions: Information Information allows you to monitor network status. Configuration Configuration allows you to configure parameters for wireless networking. Security Supports enhanced security WEP, 802.1x,WPA. 2.3.1 Information # Feature Detailed Description 2.3.1.1 General Information 2.3.1.2 Current Link Information 2.3.1.
# Feature Detailed Description 2.3.3.3 2.3.3.4 802.1x WPA STA with WEP off will never associate any AP with WEP enabled WEP Key Format: Option for Hex format Support EAP-TLS, EAP-TTLS, and EAP-PEAP Support WPA-PSK and WPA-EAP Support Cipher Mode AES and TKIP 2.4 Mechanical Requirements # Feature Detailed Description 2.4.1 2.4.2 2.4.3 Length Width Height 50.8mm 59.59mm 0.99mm 2.5 Compatibility Requirements This device passes the following compatibility requirements.
Appendix I: Rate Dependent Parameters for High Throughput .
Test Environment Diagram Fixed Attenuator (30dB) * 3 pcs Splitter (1 對 3) IP: 192.168.100.254 (Note: :For IQ-View / IQ-Flex) ) Normal Test Operating Procedure 1. Testing Steps: 8 steps in total P.S.:Pls. Install driver before insert the card. [Step 1] Run ” BC_LOG.exe ” at DUT (see Figure 1) to open test window Ex: C:\Program Files\LitePoint\IQfact\ART_MIMO_1WMPN06…B1G\MINIPCI_2071\ BC_LOG.
[Step 2] Run ” GUI.exe ” at DUT (see Figure 3) to open test window (see Figure 4). Ex: C:\Program Files\LitePoint\IQfact\ART_MIMO_1WMPN06…B1G\MINIPCI_2071\ GUI.
[Step 3] Then Kevin Serial number (see Figure 5) (Figure 5) [Step 4] (a) Plug DUT into MINI PCI / CARD BUS Interface (b) Plug RF Cable on DUT antenna three point and user a special line (MAIN-From Left to Right 0.1.2) [Step 5] Click “Run Production Test Software” to begin test.
[Step 6] Testing.
[Step 7] When test finish, it will show “PASS”(see Figure 8).
[Step 8] When show “PASS”, click “ Test ” and change the next one to continue (see Figure 8). Test Program setup [步驟 步驟 1] search the program file of ” IQ_attn.txt ” see Figure 1), (Ex: Ex: C:\Program Files\LitePoint\IQfact\ART_MIMO_1WMPN06…B1G\MINIPCI_2071\iq_setup\ IQ_attn.
[步驟 步驟 2] Test Fail (see Figure 2), (Figure 2) Alpha Networks Proprietary and Confidential Information 17