POWR3 User manual V1.
中 文 SONOFF TECHNOLOGIES CO., LTD. 使⽤说明 1. 断电 ON OFF ON OFF ON OFF ON OFF 设备安装、故障维修请由专业资质电⼯操作,以免发⽣触电危险! 2.
中 文 SONOFF TECHNOLOGIES CO., LTD. 3. 下载“易微联”APP 易 微 联 eWeLink Android™ & iOS 4. 上电 通电后,设备⾸次使⽤,默认进⼊快速配⽹模式(Touch)。 Wi-Fi指⽰灯呈“两短⼀⻓闪烁”。 三分钟内没有进⾏配⽹,设备将退出快速配⽹模式。如需再次进⼊,⻓按配对按钮5秒直到 Wi-Fi指⽰灯呈两短⼀⻓闪烁即可。 5.
中 文 SONOFF TECHNOLOGIES CO., LTD. 兼容配⽹模式 如使⽤快速添加模式配⽹失败,请使⽤“兼容模式”进⾏配对。 1 ⻓按配对按钮5秒直到Wi-Fi指⽰灯呈“两短⼀⻓闪烁”状态,松开。再次⻓按配对按钮5秒 直到Wi-Fi指⽰灯呈“快闪”状态,此时设备进⼊兼容模式。 2 在app界⾯,点击“+”,选择“兼容模式”。 Android设备: 只需输⼊Wi-Fi 码,点击“下⼀步”等待配对完成。 iOS设备: 输 ⼊ W i - F i 码,点 击“ 下 ⼀ 步 ”再 点 击“ 去 连 接 ”,将 移 动 设 备 连 接 上 W i - F i 账 号 为 : ITEAD-**********,密码为:12345678,然后回到“易微联”app,点击“下⼀步” ,等待配对 完成。 产品参数 型号 POWR3 输⼊ 100-240V ~ 50/60Hz 25A Max 输 100-240V ~ 50/60Hz 25A Max 最⼤负载 5500W Wi-Fi IEEE 802.11 b/g/n 2.
中 文 SONOFF TECHNOLOGIES CO., LTD.
中 文 SONOFF TECHNOLOGIES CO., LTD. 恢复出⼚设置 在eWeLink app端“删除设备”,设备即恢复出⼚设置。 常⻅问题 问:设备添加成功后,显⽰离线,⽆法控制? 答:设备刚添加成功后,需要1-2分钟时间连接您的路由器并连⽹。如果⻓时间还是显⽰不 在线,请根据Wi-Fi指⽰灯的状态来判断: 1. 蓝灯2秒快闪⼀下:说明设备没有连上您的Wi-Fi。 ① 可能是Wi-Fi密码输⼊不正确. ② 可能是设备离您的路由器太远,信号太弱,或环境有⼲扰。请先将设备靠近路由器,如 ⽆改善,重新添加⼀遍. ③ 设备不能识别5G的Wi-Fi,请选择2.4G的Wi-Fi重新添加. ④ 检查您的路由器后台是否开启MAC地址过滤,如有,请关闭。 如果以上均尝试不能解决,请⽤⼀部⼿机开启个⼈热点,尝试重新添加。 2.
English SONOFF TECHNOLOGIES CO., LTD. Operating Instruction 1. Power off ON OFF ON OFF ON OFF ON OFF To avoid electric shocks, please consult the dealer or a qualified professional for help when installing and repairing! 2. Wiring instruction Light fixture wiring instruction: N In N L Out 100-240V AC L In Appliance wiring instruction: L Out L In N N In Make sure the neutral wire and live wire connection is correct.
English SONOFF TECHNOLOGIES CO., LTD. 3. Download APP eWeLink eWeLink Android™ & iOS 4. Power on After powering on, the device will enter the quick pairing mode (Touch) during the first use. The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release. The device will exit the quick pairing mode (Touch) if not paired within 3mins.
English SONOFF TECHNOLOGIES CO., LTD. Compatible Pairing Mode If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode ” to pair. 1 2 Long press Pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press Pairing button for 5s again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode. Tap “+” and select “ Compatible Pairing Mode ” on APP.
English SONOFF TECHNOLOGIES CO., LTD.
English SONOFF TECHNOLOGIES CO., LTD. Switch Network If you need to change the network, long press the pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release, then the device enters quick pairing mode and you can pair again. Factory Reset Deleting the device on the eWeLink app indicates you restore it to factory setting. Common Problems Q: Why my device stays “Offline”? A: The newly added device needs 1 – 2mins to connect Wi-Fi and network.
FCC Warning SONOFF TECHNOLOGIES CO., LTD. FCC Warning Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CE Warning 1.Extreme Operating Temperature : -10 ~+40℃ 2.This product can be used across EU member states. 3.This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 20cm, It must be maintained between the user's body and the handset, including the antenna. 4.2.4GWIFI:2412~ 2472MHz,Maximum power: 16.37dBm 2014/53/EU. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.