Laser Projector User Manual
safety instructions Before using a laser projector (hereafter referred to as a projector), please read all these instructions and keep them in a safe place for future reference. 1. Read the instructions Before using the equipment, you should read all safety and usage instructions. 2. Cautions and warnings All cautions and warnings in the instructions for use should be followed. 3. Cleaning Before cleaning, unplug the power cord of the projector from the wall outlet.
Precautions for AC power cord The AC power cord must meet the relevant requirements of the country where you are using this projector. Please refer to the figure below to confirm the type of AC power cord plug you are using, and to ensure that the correct AC power cord is used. If the supplied AC power cord is not suitable for the AC outlet you are using, please consult your dealer. This projector is equipped with a grounded AC power cord plug. Make sure that the plug can be inserted into the power outlet.
Disclaimer All rights reserved The ownership of all software and hardware of this product belongs to our company. Without our permission, we shall not copy, copy or extract at will Or translation. This user manual does not have any form of guarantee, expression of position or other hints.
Introduction Projector features This projector integrates high-performance optical engine projection technology and user-friendly design, with high reliability and easy to use. This projector has the following characteristics: • The color mode provides different options designed specifically for different projector purposes.
Item list When unpacking the projector, make sure the following items are complete: 聚 焦 变 焦 Projector VGASignal line Three high service card power cable Warra nty Card Quick User Guide
Product Overview Projector appearance Front and top 1 聚焦 4 变焦 3 2 5 1. Lens 4. Focus 2. Infrared remote control sensor adjustment 5. control panel 3. Speakers (Only FHD models have configuration speakers) lever Bottom, side 7 8 6 6. Vents 7. Adjust feet 8.
back 1 23 4 5 6 7 1.HDMI OUT 5.AUDIO IN 2.MINI USB 6.AUDIO OUT 3.RS-232 4.COMPUTER IN 7.USB A 5V/1.
installation Connect the projector AV USB HDMI OUT only FHD
Adjust the height of the projector This projector is equipped with 3 adjusting feet for adjusting the image height. To raise or lower the image, you can turn the elevator feet to fine-tune the height。 • To avoid damage to the projector, make sure that the adjustment feet are fully retracted before placing the projector in the packing box. Adjust the projector focus To focus the image, turn the focus adjustment (ring) until the image is clear.
Adjust the projected image size Diagonal screen screen Lens center Vertical offset Projectio n distance XGA 4:3 screen size Projection Vertical distance [ 英寸 (mm)] offset [ 英寸 (mm)] [ 英寸 (mm)] [ 英寸 (mm)] [ 英寸 (mm)] 50(1270) 40(1016) 30(762) 77(1956) 3.8(96) 60(1524) 70(1778) 80(2032) 90(2286) 100(2540) 48(1219) 56(1422) 64(1626) 72(1829) 80(2032) 96(2438) 36(914) 42(1067) 48(1219) 54(1372) 60(1524) 72(1829) 93(2362) 109(2769) 125(3175) 141(3581) 156(3962) 188(4775) 4.5(115) 5.3(134) 6.
control panel Control panel and remote control Power Turn the projector on or off signal source Search signal source
Install the battery 1. Open the battery cover in the direction shown。 2. Insert the battery according to the icon in the compartment。 3. Replace the battery cover。 • There is a danger of explosion if the battery type used when replacing the battery is incorrect.
Remote control operation Point the remote control at the infrared remote sensor and press the button。 • The remote control may not work when other strong light sources such as sunlight or fluorescent lights shine on the remote control sensor。 • Operate the remote control where you can see the remote sensor。 • Do not shake or drop the remote control。 • Store the remote control in a cool and dry place。 • Do not splash water on the remote control or place wet objects on it。 • Do not disassemble the
Dimensions 300mm 106mm 聚焦 变焦 270mm Ceiling installation 170mm 160mm Note: It is recommended to use M4L8 screws for fixing projectors that use ceilingmounted M4 screw holes.
Specification DLP Laser Projector Model: SNP-LX3600A Input: 100-240V~, 50/60Hz, 3.5A Manufacturer: Sonnoc (Beijing) Technology Co., Ltd. Address: 806, 7th Floor, No 5, No 26, Huangsi Street, Xicheng District, 100120 Beijing, P.R. China.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.