User's Manual

ManualsBrandsSonicwall ManualsElectronicsTZ 150 Wireless / TZ 50 Wireless

Table Of Contents

SonicWALL TZ 150 Wireless Security Appliance Getting Started Guide

SonicWALL TZ 150 WIRELESS Internet Security

Appliance

Regulatory Statement and Safety Instructions

Regulatory Model/Type Product Name

APL15-03A TZ 150 WIRELESS

Class B Notice - Model APL15-03A

FCC Part 15 Class B Notice

NOTE: Models APL15-03A was tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy. And, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If the equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try

and correct the interference using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• I ncrease the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from the receiver connection.

• Consult SonicWALL for assistance.

Complies with EN55022 Class B and CISPR22 Class B.

Refer to the label on the bottom of the unit for device information including Class A or Class B

FCC information.

Caution: Modifying this equipment or using this equipment for purposes not shown in this

manual without the written consent of SonicWALL, I nc. could void the user’s authority to

operate this equipment.

 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters (7.9 inches) between the radiator (antenna) and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

For more information regarding the above statement, please contact SonicWALL, I nc. at 1143

Borregas Avenue, Sunnyvale, CA 94089-1306 or 1-408-745-9600.

SonicWALL declares that the APL15-03A (FCC I D: QWU-03A) is limited in CH1~ CH11 by specified

firmware controlled in the USA

Canada (IC):

To prevent radio interference to the licensed service, this device is intended to be operated

indoors and away from windows to provide maximum shielding. Equipment (or its transmit

antenna) that is installed outdoors is subject to licensing.

1.Operation is subject to the following two conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference that may cause undesired

operation of the device.

This device has been designed to operate with an antenna having a maximum gain of 0 dBD.

Antenna having a higher gain is strictly prohibited per regulations of I ndustry Canada.

Therequired antenna impedance is 50 ohms."

Summary of content (39 pages)

PAGE 1
SonicWALL TZ 150 WIRELESS Internet Security Appliance Regulatory Statement and Safety Instructions Regulatory Model/Type APL15-03A Product Name TZ 150 WIRELESS Class B Notice - Model APL15-03A FCC Part 15 Class B Notice NOTE: Models APL15-03A was tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
VCCI Statement Regulatory Information for Korea Ministry of Information and Telecommunication Certification Number All products are made in Taiwan R.O.C. All certificates held by NetSonic, I nc. Canadian Radio Frequency Emissions Statement This Class B digital apparatus complies with Canadian I CES-003. Cet appareil numérique de la classe B est conforme à toutes la norme NMB-003 du Canada.
PAGE 3
Cable Connections - All Models All Ethernet cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWALL is located. Power Supply Information - All Models I f the power supply is missing from your SonicWALL product package, please contact SonicWALL Technical Support at 408-752-7819 for a replacement.
PAGE 4
SonicWALL TZ 150 Wireless Security Appliance Getting Started Guide The SonicWALL® TZ 150 Wireless is a total security platform for both your wired and wireless network, delivering true layered security by integrating gateway anti-virus, intrusion prevention and content filtering capabilities for small networks in an easy-to-use, low cost platform. This Getting Started Guide provides instructions for basic installation and configuration of the SonicWALL TZ 150 Wireless.
PAGE 5
SonicWALL TZ 150 Wireless Configuration 1 2 “Collect Required Information” on page 3 “Applying Power to the SonicWALL TZ 150 Wireless” on page 4 3 “Connecting the SonicWALL TZ 150 Wireless” on page 5 4 “Accessing the Management Interface” on page 6 5 “Using the SonicWALL Setup Wizard” on page 8 6 “Registering Your SonicWALL TZ 150 Wireless” on page 17 7 “Connecting Wireless Clients to the SonicWALL TZ 150 Wireless” on page 22 8 “Connecting Computers to Your SonicWALL TZ 150 Wireless” on page 26
PAGE 6
1 Collect Required Information Internet Service Provider (ISP) Information Collect the following information about your Internet service: If you connect via You probably use Please record Cable modem, DSL with a router DHCP You do not need to provide any Internet connection information. Home DSL PPPoE User Name: Password: Note: Your ISP may require your user name in the format: name@ISP.
PAGE 7
Other Information SonicWALL Management Interface To access the SonicWALL TZ 150 Wireless Web-based management interface. These are the default settings, which you can change: User Name: admin Password: (default: password) Applying Power to the SonicWALL TZ 150 Wireless 2 1. Plug the power supply into the SonicWALL TZ 150 Wireless and into an appropriate power outlet. The Power LED on the front panel lights up green when you plug in the SonicWALL TZ 150 Wireless.
PAGE 8
3 Connecting the SonicWALL TZ 150 Wireless LAN 1 Management Station WAN DSL or Cable Modem Internet Connecting the Ethernet Cables 1. Connect one end of an Ethernet cable to your Internet connection, such as a DSL modem or cable modem. This cable may already be connected between your computer and your modem. If so, disconnect it from your computer, and leave it connected to the internet. 2. Connect the other end of the cable to the WAN port on the back of your SonicWALL TZ 150 Wireless.
PAGE 9
4 Accessing the Management Interface To access the Web-based management interface of the SonicWALL TZ 150 Wireless: 1. On the computer you have connected to port # 1, Start your Web browser. Alert: Turn off pop-up blocking software before accessing the SonicWALL management interface. Your Web browser must support Java and HTTP uploads. Internet Explorer 5.0 or higher or Netscape Navigator 4.7 or higher are recommended. 2. Enter 192.168.168.168 in the Location or Address field. 3.
PAGE 10
If the SonicWALL Setup Wizard Does Not Appear If you cannot connect to the SonicWALL TZ 150 Wireless or the Setup Wizard does not display, verify the following configurations: • Did you correctly enter the SonicWALL TZ 150 Wireless management IP address in your Web browser? • Is your computer running pop-up blocking software? • Are the Local Area Connection settings on your computer set to obtain an IP address dynamically (DHCP)? see Step 7, “Connecting Computers to Your SonicWALL TZ 150 Wireless” on page 2
PAGE 11
5 Using the SonicWALL Setup Wizard The SonicWALL Setup Wizard provides user-guided instructions for configuring your SonicWALL TZ 150 Wireless. Note: Make sure you have any required ISP information to complete the configuration before using the Setup Wizard. See the list of required information in Step 1, “Collect Required Information” on page 3. Tip: If you do not know what type of Internet connection you have, contact your ISP.
PAGE 12
Select Office Gateway, which is a commonly used wireless deployment for LAN and WLAN to Internet connectivity. 2. Change Password - Change the administrative password. This is the password for the admin account. Old Password Should be populated with the default password, password. New Password Enter your new password. Confirm Re-enter your new password. ! Note: Keep your new password in a safe place.
PAGE 13
Automatically adjust clock for daylight saving time Check this if you live in an area that observes Daylight Savings Time. Click Next. ! Note: It is important that you set the time zone correctly before you register your SonicWALL TZ 150 Wireless. 4. WAN Network Mode - The Setup Wizard automatically detects most networking modes. If it does not detect the networking mode, you may have a Static IP Address. See Step 1, “Collect Required Information” on page 3.
PAGE 14
5. WAN Network Mode - The second WAN network mode page configures your WAN settings for the selection you made in the previous page. WAN Network Mode: NAT Enabled (Static IP) SonicWALL WAN IP Address Enter a single, static IP address. This must be in the correct address range for your ISP. WAN Subnet Mask Enter the subnet mask for your network, for example, 255.255.255.0. Gateway (Router) Address Enter the IP address of your internet gateway.
PAGE 15
WAN Network Mode - NAT with PPPoE Client Obtain an IP Address Automatically Select this if your ISP assigns you a dynamic IP address. Use the following IP Address Select this if your ISP has assigned you a static IP address, and enter the address. PPPoE User Name Enter the user name for your Internet account. The username usually includes “@” and the domain name, for example, joe.user@ispgateway.net. PPPoE Password Enter the password for your internet account.
PAGE 16
SonicWALL WAN IP Address Enter the static IP address for your connection. WAN/DMZ Subnet Mask Enter the subnet mask for your connection. Gateway (Router) Address Enter the address of your Internet Gateway. Click Next. 6. LAN Settings - The LAN Settings page configures your LAN interface. These settings apply to all twenty-four LAN ports. SonicWALL LAN IP Address Accept the default IP address or enter a new IP address of the LAN interface.
PAGE 17
7. LAN DHCP Settings - The LAN DHCP Settings page allows you to select whether or not to use the DHCP Server in the SonicWALL TZ 150 Wireless to automatically distribute IP addressing information to computers and other network devices on your LAN. Enable DHCP Server on LAN Leave checkbox checked to use the DHCP server in the SonicWALL TZ 150 Wireless. Do not use select this option if you already have a DHCP server on your network, or if you want to require your network clients to have static IP addresses.
PAGE 18
allows you to create a first VPN user to connect securely to your wireless network. User Name Enter a user name for the VPN user. Password Enter a unique password for the user. Confirm Password Re-enter the password. Click Next. Note: You add additional users in the Users> Settings page in the SonicWALL TZ 150 Wireless security appliance’s Management Interface. See the SonicOS Standard Administrator’s Guide for instructions. 10.
PAGE 19
Click Next. 11. SonicWALL Configuration Summary - Displays your network configuration information. Setup Wizard Complete - your SonicWALL TZ 150 Wireless is now successfully configured for LAN, Wireless, and Internet access. Click Restart to complete the configuration process. 12. Test your connection: After the SonicWALL TZ 150 Wireless reboots, open a Web browser, and go to If you can view the SonicWALL home page, you have configured everything correctly.
PAGE 20
6 Registering Your SonicWALL TZ 150 Wireless Once you’ve established your Internet connection, it is recommended you register your SonicWALL security appliance at mySonicWALL.com.
PAGE 21
Creating a mySonicWALL.com Account Creating a mySonicWALL.com account is fast, simple, and FREE. Simply complete an online registration form in the SonicWALL TZ 150 Wireless management interface. If you already have a mysonicWALL.com account, go to “Registering Your SonicWALL TZ 150 Wireless” on page 19 to register your appliance. 1. If you are not logged into the SonicWALL TZ 150 Wireless management interface log in with the username admin and the administrative password you set in the Setup Wizard. 2.
PAGE 22
to create one.” The mySonicWALL.com account form is displayed. 5. In the MySonicWall Account page, enter in your information in the Account Information, Personal Information and Preferences fields. All fields marked with an asterisk (*) are required fields. Note: Remember your username and password to access your mySonicWALL.com account. 6. Click Submit after completing the MySonicWALL Account form. 7. When the mySonicWALL.
PAGE 23
2. If the System > Status page is not displaying in the management interface, click System in the left-navigation menu, and then click Status. 3. On the System > Status page, in the Security Services section, click the Register link. The mySonicWALL.com Login page is displayed. 4. Enter your mySonicWALL.com account username and password in the User Name and Password fields, then click Submit. 5.
PAGE 24
SonicWALL content security appliance in your mySonicWALL.com account. 7. Please complete the Product Survey. SonicWALL uses this information to further tailor services to fit your needs. 8. Click Submit. 9. When the mySonicWALL.com server has finished processing your registration, you will see a page informing you that your SonicWALL TZ 150 Wireless appliance is registered. Click Continue, and the System > Licenses page is displayed showing the available security services.
PAGE 25
7 Connecting Wireless Clients to the SonicWALL TZ 150 Wireless For wireless clients to connect to your WLAN zone, they need: • A wireless network card installed and configured for the SonicWALL TZ 150 Wireless’ SSID • SonicWALL GVC or SonicWALL GSC installed and configured for a secure wireless connection Connecting to the Wireless Network You connect to the wireless network according to the requirements of your client operating system.
PAGE 26
• • “Creating an Office Gateway Connection Profile Using the New Connection Wizard” on page 24 “Establishing a WiFiSec VPN Connection Using the WLAN GroupVPN Policy” on page 25 Installing the SonicWALL GVC or SonicWALL GSC Using the Setup Wizard If necessary, install the SonicWALL GVC. It is available either as the standalone SonicWALL GVC or as the SonicWALL GVC component of SonicWALL GSC. Follow the instructions in the Setup Wizard to install SonicWALL GVC or SonicWALL GSC.
PAGE 27
Creating an Office Gateway Connection Profile Using the New Connection Wizard 1. In your Windows Start Menu, Choose Start > Programs > SonicWALL Global VPN Client. The first time you open SonicWALL GVC, the New Connection Wizard automatically launches. If the New Connection Wizard does not display, click the New Connection Wizard icon on the far left side of the toolbar to launch it. Click Next. 2. In the Choose Scenario page, select Office Gateway. Click Next. 3.
PAGE 28
Establishing a WiFiSec VPN Connection Using the WLAN GroupVPN Policy 1. In the SonicWALL Global VPN Client window, double-click the Office Gateway profile. The Connection Warning dialog box is displayed, which informs you that all traffic that is not going to the secured VPN gateway will be blocked. 2. 3. Click Yes to continue.
PAGE 29
Connecting Computers to Your SonicWALL TZ 150 Wireless You can attach up to ten computers to your SonicWALL TZ 150 Wireless. LAN 3 LAN 4 LAN 1 LAN 2 WAN Internet Hub Configuring Computers for Your Network with DHCP If you enabled the DHCP Server in the Setup Wizard, each computer on your network must be configured to obtain its IP address dynamically. The following steps provide instruction on changing the Local Area Connection settings for several versions of Windows.
PAGE 30
6. Click OK and then OK again to apply the settings. Windows 2000 1. From your Windows Start menu, select Settings. 2. Open Network and Dial-up Connections. 3. Right click on the Local Area Connection icon, and choose Properties. 4. Highlight Internet Protocol (TCP/IP) and click Properties. 5. Select Obtain an IP address automatically. 6. Select Obtain DNS Server automatically. 7. Click OK and then OK again to apply the settings. Windows NT 1.
PAGE 31
Mounting the SonicWALL TZ 150 Wireless You can mount your SonicWALL TZ 150 Wireless on a wall or any vertical surface. Use the template on the next page as a guide for placing the mounting screws. 1. Using the template on the next page, attach two screws to the surface where you want to mount the security appliance. The mounting screws should have a head between 3/16” and 1/4” in diameter. The mounting screws should stick approximately 1/8” out from the surface. 2.
PAGE 32
SonicWALL TZ 150 Wireless Mounting Template Align front corner here Attach mounting screw here Considerations for Mounting the SonicWALL TZ 150 Wireless • Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended. • Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers • Ensure that no water or excessive moisture can enter the unit.
PAGE 33
Page 30
PAGE 34
Glossary of Networking Terms • • • • • • • • • Default Gateway - A device on an internetwork that forwards packets to another network. DHCP - Dynamic Host Configuration Protocol allocates IP addresses to computers on the network automatically without assigning a computer a static (fixed) IP address. DNS - A Domain Name System is a hierarchical naming system that resolves a domain name with its associated IP address. A DNS server looks up the name of a computer and finds the corresponding IP address.
PAGE 35
• • • • • • • Public IP Address - An IP address for a resource in your network that is published outside your network to the WAN. Router - A device that routes data between networks through IP address information in the header of the IP packet. A router forwards packets to other routers until the packets reach their destination. The Internet is the largest example of a routed network. Subnet - A portion of a network.
PAGE 36
SonicWALL TZ 150 Wireless Security Appliance Regulatory Statement and Safety Instructions Regulatory Model/Type Product Name APL15-03B, TZ 50 Note: Detailed regulatory information can be found in the electronic file, “SonicWALL_TZ_50_Regulatory_Statement.pdf,” located on the SonicWALL Resource CD provided with the unit or on the SonicWALL Web site: .
PAGE 37
Copyright Notice © 2004 SonicWALL, Inc. All rights reserved. Under the copyright laws, this manual or the software described within, can not be copied, in whole or part, without the written consent of the manufacturer, except in the normal use of the software to make a backup copy. The same proprietary and copyright notices must be affixed to any permitted copies as were affixed to the original.
PAGE 38
Notes SonicWALL TZ 150 Wireless Getting Started Guide Page 35
PAGE 39
Notes Page 36