User's Manual Part 5
Table Of Contents
- SonicWALL Internet Security Appliance
- VCCI Statement
- Canadian Radio Frequency Emissions Statement
- Class B Information
- Canadian Radio Frequency Emissions Statement
- VCCI Statement
- INDUSTRY CANADA (IC) NOTICE (APL10-01F)
- Regulatory Information for Korea
- Lithium Battery Warning
- Cable Connections
- Power Supply Information
- Mounting the SonicWALL PRO 200 , PRO 230, PRO 300, PRO 330, PRO 2040, PRO 3060, and PRO 4060
- Mounting Models APL11-027 and APL11-031
- Wall Mounting the SOHO TZW
- 1. Using the mounting plate as a template, mark the places to insert the mounting anchors.
- 2. Using a #2 Phillips screw driver, press the tip of the anchor into the marked places on the hollow wall.
- 3. Turn the screwdriver clockwise until the anchor is flush with the wall. Repeat for the second anchor.
- 4. Insert a #6 x 11/4” pan head Phillips self-tapping screw into each anchor leaving a gap for the mounting plate.
- 5. Hang the mounting plate on the screws. Use the middle row of mounting holes.
- 6. Slide the plate down to the narrowest part of the keyhole so that the mounting plate rests on the screws.
- 7. Tighten the mounting screws to secure the mounting plate.
- 8. Snap the SOHO TZW onto the mounting plate.
- Wall Mounting the SOHO TZW
- Mounting Models APL11-027 and APL11-031 on the Ceiling
- 1. Locate a metal support to hang the SOHO TZW.
- 2. Using the mounting plate as a template, mark the places to insert the mounting anchors.
- 3. Drill two holes for #6 x 1-1/4” screws in the marked location.
- 4. Install the #6 x 1-1/4” self-tapping screws leaving a slight gap for the mounting plate.
- 5. Hang the mounting plate on the screws.
- 6. Slide the plate down to the narrowest part of the keyhole so that the mounting plate rests on the screws.
- 7. Tighten the mounting screws to secure the mounting plate.
- 8. Snap the SOHO TZW onto the mounting plate.
- Other Considerations for Mounting the APL11-027 and APL11-031
Page 1
SonicWALL Internet Security Appliance
Regulatory Statement and Safety Instructions
Models APL04-016, APL04-017,1RK05-015, 1RK07-025, 1RK08-026, 1RK0A-02A,
and 1RK09-032 are FCC Class A devices (for office use only), and the following statement is
applicable to these models*:
FCC Part 15 Class A Notice
NOTE: This equipment was tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy. And if
not installed and used in accordance with the instruction manual, the device may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user is required to correct the interference at
his own expense.
Complies with EN 55022 Class A and CISPR22 Class A.
Regulatory Model/Type Product Name
APL11-027, APL11-031 SOHO TZW
APL10-01F TELE3 SP (Class B)
APL12-028 TELE3 SPi
APL04-01E TELE3 TZ and PRO 100 (Class B)
APL11-024 TELE3 TZX (Class B)
APL04-022 TELE3 (Class B) and SOHO3 (Class B)
APL04-016 PRO 100 (Class A)
APL04-017 TELE3 (Class A) and SOHO3 (Class A)
APL11-029 TZ 170
1RK05-015 PRO 200 and PRO 300
1RK07-025 PRO 230
1RK08-026 PRO 330
1RK0A-02A PRO 2040
1RK09-032 PRO 3060 and PRO 4060