Wireless Headset Series UHW-10/20 Under the Helmet FHW-10 Over the Head Operation Manual 7340 SW Durham Road • Portland, OR 97224 USA Phone: 503-684-6647 • 1-800-527-0555 Fax: 503-620-2943 • email: sales@firecom.com www.firecom.
Introduction The UHW/ FHW series offers highly reliable wireless communication headsets for fire and emergency truck operator applications. The UHW/ FHW series provides secured, digitally encoded interference free communications. When operated as part of a wireless system, up to 40 headsets can operate interference free in close proximity to each other1. 1- Although not recommended, under certain circumstances, it may be possible to operate up to 50 head sets in close proximity.
Proper Fit When worn properly, this headset will provide significant hearing protection. If it is not worn properly, the headset’s effectiveness in reducing harmful noise is severely compromised. • The length or vertical fit of the headset ear dome is adjusted by the headband or head strap. Adjust as necessary to achieve a fit that ensures the headset ear dome completely covers the ear. • This headset is intended to be a left dress headset.
Headset Power Switch and Volume Control A power switch with non detented volume control is provided. This control is located on the bottom side of the right ear dome on the UHW-10/ 20 headsets, and on the top side of the left ear dome on the FHW-10 headset. Volume should be set at a comfortably high audio level to optimize performance but not so high as to cause audio distortion and hearing discomfort.
Mic Muffs The headset microphone is covered with a washable, replaceable foam mic muff. This mic muff helps prevent the “pops” and “hisses” that can occur from speaking into a microphone that is close to the mouth. Mic muff To clean or replace the mic muff: O-ring 1. Remove the o-ring. 2. Slip the mic muff off the microphone. 3. At this time, you can decide whether to clean or replace the mic muff.
Charging All headsets have a 5.5 mm panel mounted charger jack located on the right ear dome. A charger cable assembly with 5.5mm plug is provided with the headset. The unterminated end of the charger cable can be wired to nominal 12V (11-16V) from the vehicle. Plug the terminated end of the charger cable into the headset charger jack (refer to the LED indicators section for proper operation of the battery charging red LED indicator NOTES: 1.
Never remove the charging cable from the headset by pulling on the cord. The headset should be unplugged at the jack location by pulling the charger plug from the jack. Wipe headset and ear seals with a mild soap and water mixture only. NEVER IMMERSE ANY PART OF THE HEADSET IN WATER. Although the microphone is water resistant, to ensure a longer life, keep the microphone away from moisture, when possible. Do not store in direct sunlight or in areas of high temperature. Specifications Headset Sensitivity .
FCC RF Exposure Warning: - - - This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF exposure requirements, the base unit must be installed and operated 20 cm (8 inches) or more between the product and all person’s body (excluding extremities of hands, wrist and feet). This product may not be collocated or operated in conjunction with any other antenna or transmitter.
Power - 3.7V rechargeable lithium Ion battery - 8-10 hours of talk time - Cycle life 500 cycles minimum - Over voltage, under voltage, over current and over temperature protection. - Charge source 12V nominal (11-18v). 0.25A minimum. - Change time 3 hours max from deeply discharged state.
Notes 8 9
Notes 10 9
FIRECOM is a division of Sonetics Corporation 7340 SW Durham Road • Portland, Oregon 97224 800-527-0555 • 503-684-6647 • Fax: 503-620-2943 Email: sales@firecom.com • www.firecom.com Copyright © 2008 Sonetics Corporation - All rights reserved. The information in this document is subject to change without notice. No part of this document may be reproduced in any form without prior written consent of Sonetics Corporation. This document is part number 600-0074-00 RevA. Printed in China.