Installation Guide

ManualsBrandsSolarEdge ManualsCablesSolarEdge 40a Level 2 Electric Vehicle J1772 Charge Connector w/ 25 ft Cable & Holder

EV Charger Cable Installation and EV Charger Configuration

Contents

EV Charger Cable Installation and EV Charger Configuration

Introduction 1

Package Contents 1

Required Equipment 1

Mounting the EV Charger Cable 1

EV Charger Activation and Configuration 3

EV Charger Configuration and Monitoring 4

Specifications 5

Charging Instructions 5

Version History

l Version 1.1, Apr 2018 - Clearance updated; addition of operating instructions

l Version 1.0 , Feb 2018 - Initial release

Introduction

The EV Charger Cable is used with SolarEdge‘s EV Charging Single Phase Inverter (referred to as inverter). This document describes how to install and connect

the cable and how to configure the EV Charger.

Package Contents

l A holder that is mounted on a wall/ pole (screws are not included)

l EV Charger Cable

l Cable lock

Required Equipment

l 4 screws

l Screwdriver

l Drill

NOTE

Connection to the SolarEdge monitoring platform is required for first EV charging.

Mounting the EVCharger Cable

Install the EV Charger Cable after the inverter is already installed (refer to the Inverter Installation Guide).

Connect the EV charger Cable to the inverter (see Figure 1):

a. Align the two white arrows on the EV charger cable connector with the white dot on the inverter connector located at the bottom of the inverter: the

dot should be between two arrows.

b. Plug the connector into the EV connector.

c. Rotate the cable connector clockwise to fasten it.

EV Charger Cable Installation and EV Charger Configuration MAN-01-00445-1.1

Figure 1: EV cable connection

Summary of content (5 pages)

PAGE 1
EV Charger Cable Installation and EV Charger Configuration Contents 1 1 1 1 1 3 4 5 5 EV Charger Cable Installation and EV Charger Configuration Introduction Package Contents Required Equipment Mounting the EV Charger Cable EV Charger Activation and Configuration EV Charger Configuration and Monitoring Specifications Charging Instructions Version History l l Version 1.1, Apr 2018 - Clearance updated; addition of operating instructions Version 1.
PAGE 2
EV Charger Cable Installation and EV Charger Configuration 2. Determine the mounting location, on a wall, stud framing or pole. Maintain the following minimum clearance areas between the holder and other objects: l 8" (20 cm) from the top and sides of the holder l 24" (60 cm) - 4 ft (1.2 m) from the bottom of the holder 3. Position the holder against the wall/ pole and mark the drilling hole locations. 4. Drill the holes. 5.
PAGE 3
EV Charger Activation and Configuration EV Charger Activation and Configuration After installing the EV Charging Single Phase Inverter, and the EV Charger Cable, the EV Charger should be activated in order to enable charging. This chapter describes how to activate and configure the EV Charger using the SolarEdge monitoring platform mobile application. NOTE Connection to the SolarEdge monitoring platform is required for first EV charging. 1.
PAGE 4
EV Charger Cable Installation and EV Charger Configuration 5. When the EV Charger is activated and ready for configuration, the following screen is displayed. Tap OK. Figure 6: EV Charger activated EV Charger Configuration and Monitoring 1. Before starting, make sure that: l l l The inverter is installed and activated (refer to the Inverter Installation Guide) The EV Charger Cable is installed The EV Charger activation is complete 2. Access the SolarEdge monitoring app. 3.
PAGE 5
Specifications Specifications EV Charger Connector SAE J1772-2009 Charging Cable Length 25 ft./ 7.6 m (15 ft./ 4.6 m option) Charging Cable Weight 12.5 lb./ 5.7 kg (7.7 lb./ 3.5 kg for the 15 ft./ 4.6 m option) Holder Weight 0.6 lb. / 300 gr Charging Instructions 1. Verify that the green LED at the bottom of the inverter is ON indicating that the EV Charger is ON and ready to charge. 2. Hold the EV Charger plug and unwind the cable from the holder. 3.