Notification Pager Manual 1
Notification Pager Notification Pager Functions Notification pager will notify the operator (Sound/Vibration) when irregular occur during autonomous cleaning or when the machine encounters obstacles. When using the notification pager for the first time, please take the pager out of the battery box and charge the pager. (⇒see "Recharging the Notification Pager'). Notification pager can only be used during autonomous cleaning. No.
Notification Pager Functions & Usage When the machine detects danger or detects an obstacle, an alert will be displayed on the notification pager(⇒see "Alert display and its notification timing")and it notifies the operator by emitting an alert and vibrating. It emits an alert and vibrates for 15 seconds then stops for 5 seconds, which it repeats for 10 minutes. After the error with the machine has been resolved, the notification pager sounds for 1 second and its display indicates standby.
Alert display and its notification timing Appearing on display Description Appearing on display Description Standby (within the communi Autonomous cleaning complet cation range/paired) e Machine battery level low No machine battery remainin g Dustbag full Connected for wireless comm unication Connection for wireless com Error alert munication not possible ・When danger has been (outside communication rang dete e/not paired) cted near obstacles or steps ・When the emergency stop b utton ha
Turning the Notification Pager On/Off When using the notification pager for the first time, use the supplied pin to turn the power On. Turning the Notification Pager On 1 Insert the supplied pin in the power button on the side of the notification pager Keep the inserted pin pressed until the notification pager vibrates. An icon appears on the display.
Turning the Notification Pager Off 1 Insert the supplied pin in the power button on the side of the notification pager The display goes out.
Paring the Notification Pager In order to receive the alert on the notification pager, the pager must be paired with the machine itself. 1 Turn On the notification pager and the machine 2 Check if the machine is connected to the Robot Operations Center (ROC) Please check your mobile phone cellular connection in advance. Robot Operations Center (ROC) will not be conn ected to LTE in an area where there is no signal.
3 Press the button on the notification pager for at least 5 seconds The message "Wireless connection in process" will be shown on the pager's display. 4 Attach the pager on to the pager holder on the side of the machine Carry out autonomous cleaning and check if you will recieve the alerts (⇒see "Carrying Out Autonomous Cleani ng").
Recharging the Notification Pager If notification pager battery is running low, charge the pager fully before using it. 1 Insert the Micro USB plug on the cable in the terminal on the back of the notification pager charger 2 Connect the USB plug on the cable in the USB AC adapter, and plug the adapter into an outlet The customer must purchase a USB AC adapter themselves. 3 Place the notification pager in its charger An AC adapter is not included in the product package.
Safety Precautions About safety Precautions Precautions presented here are intended to prevent harm to the user and other persons as well as damage to property. Always observe them. SoftBank Robotics shall not be liable for any damages incurred by the user or any third person as a result of the malfunctioning, mis operation, trouble, etc. experienced by the machine, notification pager, battery, or battery charger.
Description of Symbols The following symbol categories explain the level of harm or damage that will occur if indications are not observed and equipment is used incorrectly. Read the guide after thoroughly understanding the indications. DANGER Indicates a “probability of immediate danger of death or serious injury* 1” with incorrect handling. Indicates a “possibility of death or serious injury* 1” with incorrect handling.
Handling the Notification Pager DANGER Do not drop or throw. Subjecting it to strong impact may cause the battery pack in the notification pager to leak, overheat, rupture, or ignite, and may cause fire, electric shock, malfunction, etc. WARNING Do not place the notification pager or notification pager charger in a cooking device (microwave oven , etc.) or high-pressure container (pressure cooker, etc.), or on top of an electromagnetic cooking dev ice (IH cooktop).
Pictorial Symbols Refer to the labels on each product (the machine, battery charger, battery). Each is compliant with the Japanese Electri cal Appliances and Material Safety Act (Spec ified Electrical Appliances and Materials). Incorporates a specified wireless system as defined by Japanese law (TELEC or JATE-cer tified). Do not short-circuit. Do not disassemble. Do not immerse in water or other liquid.
FCC ID: 2ATI9-P00000401A01 Specific Absorption Rate (SAR) During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage, and near the body with the separation of 0.0 inches (0 mm). Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. These requirements set a SAR limit of 1.
CE Body SAR(5mm)≤2.0W/kg(10g) Limbs SAR(0mm)≤4.0W/kg(10g) The Specific Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the body when using a device. This device meets guidelines for exposure to radio waves, and is designed not to exceed those limits. Do not dispose of used device in a household rubbish bin. The device connected to a USB interface of version USB2.0.