® Go Wi-Fi! P322/P322X 802.
8/2011 Document # 6410-00315 D Copyright Notice Copyright © 2009-2011 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo and Go Wi-Fi! are trademarks or registered trademarks of Socket Mobile, Inc. Wi-Fi® is a registered trademark of the Wi-Fi Alliance. All other brand and product names are trademarks of their respective holders. Reproduction of the contents of this manual without the permission of Socket Mobile is expressly prohibited.
Table of Contents Copyright Notice..................................................................................................2 1. Introduction....................................................................................................4 1.1 Key Features Supported........................................................................4 1.2 System Requirements ............................................................................4 2. Installing the P322/P322X Driver .......................
1. Introduction Thank you for purchasing the Socket Go Wi-Fi! P322/P322X 802.11a/b/g SDIO WLAN card. This User’s Guide provides instructions for using the P322/P322X driver on ARMV4I processor based handheld devices running the Windows Mobile 5 or 6 operating system. 1.1 Key Features Supported The provided Go Wi-Fi! P322/P322X driver has the following features and security protocols: • Supports 802.11a/b/g • Works with Microsoft Wireless Zero Config (WZC) software • Supports Windows Mobile 5.
2. Installing the P322/P322X Driver 2.1 Installing the driver CAB file with a Memory Card 1. Copy the driver CAB file from the Driver CD onto a memory card. Alternatively, download the driver CAB file online from: http://www.socketmobile.com/support/downloads/ 2. Insert the memory card into the device. 3. Use File Explorer to copy the CAB file to the device, then navigate to the CAB file 4. Tap on the CAB file to install it. Follow the instructions to complete the installation 2.
5. Follow the InstallShield Wizard to complete the driver installation Go Wi-Fi! P322/P322X User’s Guide © Socket Mobile, Inc.
3. Create Access Point Profile 1. Insert the Go Wi-Fi! P322/P322X card into the SDIO slot of your device. Once the WLAN card is initialized and the driver is loaded, a radio tower icon shows up at the top bar. 2. Tap on the tower icon, then on the “Settings” on the pop-up Connectivity window, it will take you to the following screen. Go Wi-Fi! P322/P322X User’s Guide © Socket Mobile, Inc.
3. Click on “Wi-Fi”, it will show the list of the available WLAN access points. 4. Select the access point that you want to connect to (in this example: “atheros_test”). Click on the menu item “Connect”. If it is the first time connecting to this access point, it will create a new profile. Otherwise, it will start the WLAN connection Go Wi-Fi! P322/P322X User’s Guide © Socket Mobile, Inc.
5. If it is the first time connecting to the access point, it will bring you to the following profile creation screens. At the first screen, you can enter “Network name”. The access point name is used as the default network name. Follow the “Next” soft key to move to the next screen. 6. Next, select the authentication and encryption methods corresponding to the selected access point. Then, enter the right network key.
4. Connect to the Access Point 1. Once you finish the profile creation or you clicked “Connect” on an access point with profile already created, the PDA starts to try connecting to the WLAN access point you selected. 2. The screen below shows that the device is connected to the access point. Go Wi-Fi! P322/P322X User’s Guide © Socket Mobile, Inc.
5. Check IP Address after WLAN Connection You can check the IP address assigned to the device by going to the “Network Adapters” tab and select the “P322 WLAN SDIO” entry. You can check the network connectivity by pinging this IP address from a network computer. Go Wi-Fi! P322/P322X User’s Guide © Socket Mobile, Inc.
6. Technical Support Socket has two technical support resources to help you. Please note that support is available only in English. Online Knowledge Base: Search for articles, Frequently Asked Questions or Hot Topics 24 hours a day. http://support.socketmobile.com/EU_S1a.asp Online Requests: Register your product and submit a question to our Technical Support team. http://support.socketmobile.
7. Limited Warranty Socket Mobile Incorporated (Socket) warrants this product against defects in material and workmanship, under normal use and service, for one (1) year from the date of purchase. Product must be purchased new from a Socket Mobile Authorized Distributor or Reseller. Products purchased through non-authorized channels are not eligible for this warranty support.
7.1 Limited Software Warranty LIMITED WARRANTY. Socket Mobile, Inc. (Socket) warrants that the original disk or CD ROM is free from defects for 90 days from the date of delivery of the SOFTWARE. CUSTOMER REMEDIES. The entire liability of Socket and your exclusive remedy shall be, at the option of Socket, either (a) return of the price paid or (b) replacement of the SOFTWARE which does not meet the Socket Limited Warranty and which is returned to Socket with a copy of your receipt.
PORTIONS OF THIS SOFTWARE ARE PROVIDED BY THEOPENSSL PROJECT OR ERIC YOUNG “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
8. Regulatory Compliance 8.1 English Go Wi-Fi! cards are designed to be compliant with the rules and regulations in locations where they are sold and will be labeled as required. This product is type approved and users are not required to obtain license or authorization before using. USA • FCC Part 15 Subpart B Class B Section 15.107, 15.109 • FCC Part 15 Subpart C Section 15.207, 15.247 • FCC Part 15 Subpart E Section 15.207, 15.209, 15.407 • FCC Procedure ANSI C63.
The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). IMPORTANT NOTE: Federal Communications Commission (FCC) Radiation Exposure Statement This EUT is compliant with SAR for general population / uncontrolled exposure limits in ANSI / IEEE C95.1-1999 and has been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C.
8.2.1 Déclaration d'interférence de la FCC Ce matériel a été contrôlé et correspond aux limites imposées pour les dispositifs numériques de classe B, conformément à la section 15 des règlements FCC. Ces limites sont destinées à assurer une protection suffisante contre les interférences nuisibles dans un milieu résidentiel.