Owner’s Manual SSLM7BA1 MONITOR-SLIMLINE 7 INCH-A SSLM7BB1 MONITOR-SLIMLINE 7 INCH-B -1-
MONITOR-SLIMLINE 7 INCH Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver’s seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, the unit should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle.
Welcome Thank you for purchasing this Headrest Video Monitor with built-in DVD player. Before operating this system, read this manual thoroughly and retain it for future reference.
Table of Contents 1.
Type of Discs your DVD will Play ······································································································ 23 Loading and Playing Discs ·················································································································· 23 To Load and Play a Disc ······················································································································ 23 7.
12. Technical Data······································································································································ 33 13. Troubleshooting ··································································································································· 35 14. FCC Notice··········································································································································· 37 15.
Optional Accessories Wireless Headphone This SLIMLINE includes a built-in dual channel infrared transmitter for use with a wireless headphone. The volume can then be adjusted with the controls on each headset. The wireless headphone must be used within a line of sight from the transmitter, as infrared transmission, like visible light travels only in a straight line. Wired Headphone There is a 1/8-inch headphone jack on the device that can be used with any standard stereo headphone.
Installation Sequences After safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation.
-9-
Router Cabling under Driver Seat & Passenger Seat • Connect 6-pin signal cord 1A (white) and 6-pin signal + power cord 2A (red) of driver seat to corresponding with the connectors of signal cord 3A, and then fix both connectors with a clamp if available. And connect other end connectors (white and red) of signal cable 3A to corresponding with connectors of Control Box as shown below. Repeat for passenger seat. • Connect FM antenna cable to Control Box 2-pin connector.
Functional Verification Accessory Function Checks: Turn vehicle ignition to ON, depress power button on each headrest monitor. Insert disc into DVD player, press ENTER button on the remote control or LCD panel. Listen with wireless headphones (be sure to set to channel “A” to listen to Monitor A and channel “B” to listen to Monitor B. Connect jumper cable from output Monitor A to inputs on Monitor B, and then press source button on Monitor B to “AV”.
Control Description on the Front Panel - 12 -
1. DVD Player Busy Light • Caution children to avoid touching or The busy light indicates the activity state of the scratching the screen, as it may become dirty or DVD player. damaged. 2. DVD Compartment Slot 6. USB 1.1 Port Insert a disc to play. You can play videos, music, and images stored 3. IR Sensor - Forward Sensor Eye in a USB device such as USB-compatible stick Allow the remote control to navigate the OSD ( memory or memory card reader, etc. On Screen Display) on the device and to control 7.
12. STOP/LEFT Button This button function allows you to navigation the contents when enter DVD menu, besides this button is act as STOP function for DVD playback control. 13. POWER/SOURCE Button - Switches device ON or to standby/on mode. - This device is turned on by selecting a source. Press to cycle through all of the available sources. - The device will turned off by press this button exceed over 3 seconds when the device on status. 14.
Remote Control Operations Installing the Battery Before attempting to operate your remote control, install the batteries as described below. 1. Turn the remote control face down. Press down on the ridged area of the battery cover and slide it off. 2. Install two “AAA” batteries as shown. Make sure that proper polarity (+ or -) is observed. 3. Slide the cover back until it clicks. The remote control will operate this device. It is not a universal remote control and will not control other equipment.
Button Function Descriptions 1. SOURCE Any video equipment connected to the audio/video inputs can be used with the monitor by pressing this button. Each time the button is pressed, the audio/ video source will change in the following sequence: Monitor A→Monitor B→AUX→TV. 2. POWER Press the button to turn the SSLM7BA1/SSLM7BB1 device on. The current video source will be displayed on the screen, and the picture will appear in a few seconds. Press the button again to turn the device off. 3.
7. MENU Press the button to go to the Root Menu included on the disc. 8. UP, DOWN For DVD: Navigation button, you can use this button to move the select bar to one of items among the menu or file list. For TV: Use these buttons to advance to the next higher or lower channel. For OSD: Increase or decrease the setting of selected item. 9. LEFT, RIGHT Navigation button, you can use this button to move the select bar to one of items among the menu or file list. 10.
15. SUBTITLE Press this button. If the current disc has different subtitles options, this now appears on the screen. Press this button repeatedly until you have reached your desired subtitles option. 16. Numbers Decimal number: 0 to 9; and +100: Add 100. 17. PLAY/PAUSE While playing, press this button once to pause the playback, press the button again to resume the playback. 18. STOP Stop playing the movie or songs. STOP→PLAY: Resumes disc playback. STOP→STOP→PLAY: Resumes from the beginning of the disc.
23. TV-Monitor B (If TV mode is available) Transmit IR codes for TV mode of monitor B. 24. DVD-Monitor B Transmit IR codes for DVD mode of monitor B. 25. SOUND AROUND SELECT (If available) Select a FM transmitter channel. There are 6 channels: CH1: 88.3MHz; CH2: 88.7MHz; CH3: 89.1MHz; CH4: 89.5MHz; CH5: 89.9MHz; CH6: 90.3MHz. 26.
red. When the SKIP mode is on, the device will be tuned to only the stored channels when using the UP/DOWN buttons. 31. AUDIO Press this button. If the current disc has different language options, this now appears on the screen. Press this button repeatedly until you have reached your desired language option. 32. ANGLE View with a different camera angle (The button takes effect only on the DVD that supports frames with multiple angles).
38. PBC (Video CD only) Turn the PBC (Play Back Control) on or off. 39. ZOOM Enlarge the picture in the movie by 2x, 3x, and 4x, or Shrink the picture in the movie by 1/2x, 1/3x, and 1/4x. 40. NEXT When a disc has more than one Chapter, Track, or File, you can move to another Chapter/Track/File. Press the button briefly during play to select the next Chapter for DVD-video or Track/File for VCD, SVCD, MP3, CD, etc. 41.
General Operating Instructions Turning the Device ON or OFF 1. Pivot the screen downward until a comfortable viewing angle is reached. 2. Pressing the POWER button on the lower-left corner of the front panel or the remote control will turn the device on or off. When in use, the controls will be lit. 3. After the device has been turned on and is displaying a picture, adjust the viewing angle by pivoting the screen to optimize the picture quality. 4.
DVD Basic To get the most use out of each DVD, make sure you read this section completely. Regional Coding Both the DVD player and disc are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The system’s code may be region 1. Other regional may not be played in this system. Type of Discs your DVD will Play DVD-Video: DVD contains video. CD-DA: CD contains musical or sound content only. CD-Video: CD contains movie only.
Notes on Discs • To keep a disc clean, do not touch its surface. Handle the disc by its edge. • Keep your discs in their cases or disc magazines when not in use. Also, do not subject disc to heat/high temperature. Avoid leaving them in a parked vehicle or on a dashboard/rear tray. • Do not attach labels, or use discs with sticky ink/residue. Such discs may stop spinning when used, causing a malfunction, or may ruin the disc. • Do not use any discs with labels or stickers attached.
How to use the DVD OSD Menu This section describes how to set and adjust using the on-screen setup pages included in the OSD Menu. You can use the OSD menu screen to adjust all the settings on your screen. Follow the steps outlined below to select the function you desire, and refer to the pages indicated for more information. Using the Setup Menu Using the setup display that you can do the initial setup, adjust the picture quality, and set the various output.
General Setup Page Setting the Language for On-Screen Display Press the SETUP button on the remote control, use the buttons to navigating to General Setup Page, then use the buttons to select OSD Lang sub-menu. OSD (On Screen Display) Language Menu The OSD Lang sub-menu allows the user to select the language for the on-screen display. Press the button and then use the buttons on the remote control to select the desired language. The user can select either English, French, or Spanish for the OSD language.
Preference Page Default Setting Press the SETUP button, and use the and buttons on the remote control to navigate to the Default sub-menu under Preference Page. The default setup allows you to reset all options to factory defaults. Press the button and then press ENTER button to carry out the reset. Note: This function will not effect the parental setting.
Password Setup Page Setting for Password (Parental Control Password) Press the SETUP button and navigate to the Password submenu under the Password Setup Page. The menu appears and allows you to change the parental control password. Press the button and then press the ENTER button on the remote control to entering the sub-menu. Old Password Input the old password or the default password (4 digits). New Password Input a new password (4 digits) using numeric buttons.
Playing Audio CD When playing an audio CD, the DISPLAY banner appears automatically. It displays the current track and the amount of the time that track playing, the total amount of time on the disc and the current time running on the disc. Press the DISPLAY button on the remote control to display the DISPLAY banner. The options below show you what happens when you press the DISPLAY button. Press DISPLAY (1x) “Single Elapsed” appears along with the current track playing and the time of that track.
Playing MP3 Discs MP3 is the format for storing digital audio. An audio CD-quality song can be compressed into the MP3 format with very little loss of quality, while talking up much less space. CD-R discs that have been encoded in MP3 format can be played on your DVD player. Press the DISPLAY button on the remote control to show DISPLAY Banner. The options below show you what happens when you press the DISPLAY button.
shift to left side of the screen and the song s in the folder appear on the right). 3. Press the UP or DOWN arrow button on the remote control to go through the song list and highlight the song you want. Press the ENTER button to begin the playback of the highlighted song. Skipping Songs Use the (NEXT) button on the remote control to move to the next song. Use the (PREV) button to move to the beginning of the currently playing song. Press the button 2 times to move to the previous song.
How to use the Device OSD Menu Picture Adjustment This section describes how to set and adjust using the on-screen in the device OSD Menu. You can use the device OSD menu screen to adjust advanced picture selections on your screen. • Press the PIX button by continuously hitting on the remote control to select the BRIGHTNESS, CONTRAST, SATURATION, HUE, SHARPNESS, IR HEADPHONE, RESET options to adjust value and setting. • After selecting the desired option, and use the or buttons to adjust the setting.
Technical Specification Dimensions Weight 204.90(W)x160.18(H)x57.62(D) mm 1.26Kg Operation <16W (max.) Power Consumption <1.5W (max.) Standby LCD Backlight LED Resolution 480x3(RGB)x234 for 7-inch TFT LCD Panel Luminance 400cd/m2 (min.) DVD Slim Type Slot-In Loader DVD (Single, Dual Layer), DVD-R/+R, DVD+R Dual layer, Supported Disc DVD-RW/+RW, CD, CD-R, CD-RW DVD-Video Navigation Ver1.0, VCD Ver1.0/2.
20Hz~20KHz ± 1dB ≥ 85dB ≤ 0.02 40dB POWER/SOURCE, STOP/LEFT, UP, SETUP/ENTER, Control Button on the Front Panel PLAY/PAUSE/RIGHT, EJECT, and DOWN USB 1.
Troubleshooting If it appears that the device is faulty, first consult this checklist. It may be that something has been overlooked. Symptom Device does not power “ ON” IR sensor inoperative Poor in vehicle radio reception (FM modulator installed) Disc won’t play Play starts, but then stops immediately Remedy • Check if both plugs of the main cord are properly connected. • Is ignition turned “ON”? • Are batteries installed in remote control? • Verify that the batteries in the remote control are fresh.
No picture Distorted picture Cannot advance through a movie No sound or distorted sound Player does not respond to all operating commands during playback Device feels warm • Check that the signal source is connected. • Check that the setting may be in the wrong status. Match your source selected correctly. • Contact the service department. • Check the disc for fingerprints and clean with a soft cloth, wiping from center to edge. • Sometimes a small amount of picture distortion may appear.
FCC Notice This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
WEEE Notice Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems). This symbol on the product or on its packaging indicates that device shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
