M55 SIP DECT Handset Quick Installation Guide
Important Safety Information This symbol is to alert you to important operating or servicing instructions that may appear on the product or in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock. Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1.
12. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 13. Do not overload wall outlets and extension cords. 14.
19. Use only the power cord indicated in this manual. 20. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 21. In wall mounting position, make sure to mount the telephone base on the wall by aligning the eyelets with the mounting studs of the wall plate. Then slide the telephone base down on both mounting studs until it locks into place. Mount the device only at heights not exceeding 2 meters.
For cUL compliance only Mesures de sécurité importantes Ce symbole vous alertera d’informations importantes ou d’instructions d’entretien pouvant apparaître dans ce guide d’utilisation. Respectez toujours les mesures de sécurité et de sécurité de base lorsque vous utilisez ce produit, afin de réduire les risques de blessures, d’incendie, ou d’électrocution.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire. 11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez pas de liquides dans l’appareil. 12.
adéquate. Une étincelle dans ces endroits pourrait provoquer un incendie ou une explosion. Ces environnements pourraient être l’utilisation médicale de l’oxygène sans ventilation adéquate; le gaz industriel (dissolvants, vapeurs d’essence, etc.); une fuite de gaz naturel, etc. 17. Placez uniquement le combiné de votre appareil près de votre oreille lorsqu’il est en mode de conversation normal. 18.
• Le remplacement d’une pile d’un type incorrect peut entraîner une explosion ou la fuite d’un liquide ou d’un gaz inflammable. • Évitez de jeter une pile dans le feu ou dans un four chaud, ou d’écraser ou de couper mécaniquement une pile, car cela peut provoquer une explosion. • Évitez de laisser une pile dans un environnement où la température est extrêmement élevée, ce qui pourrait provoquer une explosion ou une fuite de liquide ou de gaz inflammable.
Compliance FCC Part 68 Consumer Information: a. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back or bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. b. An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e.
Compliance h. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. i. NOTICE: If you have specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. j.
RESET RESET RESET About this Guide RESET This quick installation guide provides a reference for the external features of the M55 SIP DECT Handset and installation instructions. The M55 SIP DECT Handset is for use with the M500 Multi-cell SIP DECT Base Station. Please refer to the M55 SIP DECT Handset User Manual for complete operation instructions.
Quick Reference Guide 1 2 10 3 13 11 14 4 5 5 6 12 7 8 9 1 Earpiece 7 SPEAKER key 2 MESSAGE LED 8 Alphanumeric keypad 3 Color screen 9 Microphone 4 Soft keys 10 - VOLUME + key 5 Line 1-6 programmable feature keys 12 OFF/Cancel key 6 11 Programmable key ¡ MENU/Confirm key and 13 Belt clip navigation keys 14 Speaker 12
Handset Installation This section assumes that your network infrastructure is established and that your IP PBX phone service has been ordered and configured for your location. Handset installation involves both the handset and the handset charger. The handset charger is powered using the supplied power adapter. The handset chargercan be placed on a flat surface or mounted on a wall.
Use only Supplied Installing the charger Install the charger as shown below. Plug the power adapter into an electrical outlet not controlled by a wall switch.
IMPORTANT INFORMATION 1. Use only the power adapter supplied with this product. To order a replacement power adapter, visit our website at www.snomamericas.com . 2. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. Battery installation and charging Install the battery as shown on the following page.
To install the handset battery: Place the top of the battery in the handset battery compartment so that the battery connectors are aligned. 1. 3. Align the cover flat against the battery compartment, then slide it upwards until it clicks into place. 2. Push the bottom of the battery down into the battery compartment. Rechargable Li-ion battery MODEL: 503860AR1500 Battery Capacity: 1500mAh 3.7V Li-Ion Energy: 5.55Wh Date:2021.04 Manufacturer: Yiyang Corun Battery Co.
4. Charge the handset by placing it face forward in the charger. The battery icon indicates the charge status as the battery charges. Very low battery. Charging less than 30 minutes. Charging less than 30 minutes. Charging 30 to 80 minutes. Charging 80 minutes to 7 hours. Charging more than 7 hours. Fully charged at 11 hours. IMPORTANT INFORMATION • Use only the supplied rechargeable battery or replacement battery (model number 503860AR1500). To order a replacement battery, visit our website at www.
Wall mounting the charger The charger is ready for tabletop use. If you want to mount the charger on a wall, use two 10 mm (3/8 inch) screws and wall anchors to hold the charger in place. Screws and wall anchors are not provided, but are available for purchase at hardware retailers. You might need a professional to install the charger. To mount the charger on the wall: 1. Use a pencil to mark the desired positions of the two holes on the wall.
Registering the handset to the base station The handset must be registered to the base station in order to make and receive calls. There are three methods of registration: • Auto registration • Manual registation (triggered via Web UI). • Manual registation (triggered via LINK button on base). Registering the handset - Auto registration 1. Make sure the base station is connected to power and the network. 2. Press the MENU/Confirm key. The User Settings screen appears. 3.
Registering the handset - Manual registration (triggered via Web UI) 1. Make sure the base station is connected to power and the network. 2. Press the MENU/Confirm key. The User Settings screen appears. 3. Press or to scroll down to Registration and press OK. The Registration screen appears. 4. With This device selected, press OK. The “This device” screen appears. 5. Press or to scroll down to The base Web UI and press OK.
Registering the handset - Manual registration (triggered via LINK button on base) 1. Make sure the base station is connected to power and the network. 2. Press the MENU/Confirm key. The User Settings screen appears. 3. Press or to scroll down to Registration and press OK. The Registration screen appears. 4. With This device selected, press OK. The “This device” screen appears. 5. With The base LINK key selected, press OK.
Deregistering the handset Before using the handset with a different base station, you must deregister the handset from the base station to which it is currently registered. To deregister the handset: 1. 2. 3. 4. 5. Press the MENU/Confirm key. The User Settings screen appears. Press or to scroll down to Registration and press OK. The Registration screen appears. Press or to scroll down to Deregistration and press OK. The “Dereg. HS” screen appears, showing the list of registered handsets.
Maintenance Taking care of your telephone • Your base station and cordless handset contain sophisticated electronic parts, so you must treat them with care. • Avoid rough treatment. • Place the handset down gently. • Save the original packing materials to protect your products if you ever need to ship them. Avoid water • You can damage your cordless telephone if it gets wet. Do not use the handset in the rain, or handle it with wet hands.
VTECH COMMUNICATIONS, INC. Tigard, Oregon 97223, USA. Copyright © 2022 Snom Technology GmbH. All Rights Reserved.