Annex no. 5 Functional Description / User Manual State: 2010-03-01 m. dudde hochfrequenz-technik Vers. no.: 1.10 Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel.
Project Documentation | EKTSDG-010000 Target Simulator Doppler Generator Project Number: SMS Project Number: Project Title: Handheld Radar Target Simulator Doppler Generator Keyword(s): Electronic Radar Target Simulator Doppler Generator K-Band Date: June 7, 2012 Document: UserManual_EKTSDG.doc Status: Ready Review done Approved Delivered Outdated/invalid PROPRIETARY The information contained in this document may be subject to change without notice.
Contents 1 2 3 4 5 6 7 8 Document Revision History ............................................................................. 3 Overview ....................................................................................................... 4 2.1 Features .................................................................................................. 4 2.2 Applications ............................................................................................. 4 Getting Started ...................
1 Document Revision History Table 1-1: Document Revision History Date 2012-02-08 2012-03-21 2012-06-07 Editor Michaelis Mende Hadasch Description Initial design of document Review Added chapter 7: Declaration of conformity for USA PROPRIETARY The information contained in this document may be subject to change without notice. The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH. 2012-06-07_UserManual_EKTSDG.
2 Overview The EKTSDG-010000 (Elektronic K-band Target Simulator/ Doppler Generator) is a handheld portable moving target simulator for K-band Radar transceivers. It can be used for calibrating and testing speed displays, door openers, safety systems and other radar based Doppler sensors. The EKTSDG-010000 uses a linear polarized antenna. A software generated modulation signal allows generation of low distortion and directional Doppler signals from 44Hz to 9kHz corresponding to speeds from 1km/h to 200km/h.
3 Getting Started This chapter explains the first steps of using the EKTSDG device and the EKTSDGRemote Software. 3.1 Equipment Needed EKTSDG Device USB Stick with EKTSDG-Remote Software PC with Windows 2000/XP/Vista/7 3.2 EKTSDG-Remote Software EKTSDG may be connected via USB to any Windows PC. The included EKTSDGRemote software allows realtime remote controlling and configuring the presets of the EKTSDG. 3.3 Installing from USB Stick 1. Remove any EKTSDG system connected to your system 2.
3.4 EKTSDG-Remote Screen After launching the EKTSDG-Remote Software, the screen below should appear. Figure 1: EKTSDG-Remote Screen See section 3.2 for details on this software. PROPRIETARY The information contained in this document may be subject to change without notice. The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH. 2012-06-07_UserManual_EKTSDG.doc I Page 6 of 15 I June 7, 2012 www.smartmicro.
4 EKTSDG Handheld Operation 4.1 Controls (5) Power Indicator (1) Power On (6) Antennas (2) Preset Selector (3) Charge Indicator (7) Active Preset (4) USB Connector Figure 2: Controls and Displays 4.2 Using EKTSDG 4.2.1 General Remarks Prepare the settings as described in section 5.2. Maximum distance depends on the radar sensitivity and the amplitude settings of EKTSDG. 4.2.
Press Power switch (1) while pressing the Preset selector (2) > EKTSDG default preset LED (7) blinks 1. Repeat pressing the Preset selector (2) until the desired preset LED (7) flashes > after 1 second, the selected LED (7) stops blinking and EKTSDG runs the selected preset > the selected preset will become the new default preset 1. PROPRIETARY The information contained in this document may be subject to change without notice.
5 EKTSDG-Remote Software Legend of Controls: 1 5 8 2 3 4 6 7 9 Figure 3: EKTSDG-Remote Software Screen 10 1. Doppler Signal ON/OFF 2. Direction of Movement 3. Doppler Amplitude (simulates object distance) 4. Object Speed parallel to (5) 5. Object Speed parallel to (4) 6. Select Speed Display Unit 7. Copy Settings to Preset Memory 8. Select Standard Preset 9. Duration of Doppler Signal 10.
5.2 Configuring EKTSDG EKTSDG starts up with a “default preset”. This is one of three configurable presets. All presets can be configured by means of the EKTSDG-Remote software or with a terminal software. Default preset can also be selected manually directly with the EKTSDG. See section 4.2.4. 5.2.1 Storing Settings as Presets 1. Select the desired parameters in the Live Setting section with controls (1) to (6) 2. Copy these parameters to the desired preset with selector (7) 3.
6 EKTSDG USB Serial Interface EKTSDG can optionally be operated by a terminal program or by customer software. The USB port is represented as serial interface by the driver software, that has been installed according to section 3.3. 1. Connect EKTSDG 2. Start EKTSDG-Remote software or check the windows control panel to get the assigned COM port. Close EKTSDG-Remote software before opening terminal software! 3. Open a terminal program like Windows Hyper Terminal 4. Select the appropriate COM port.
6.2 Terminal Mode: Preset Setting For using presets please refer to section 4.2. Presets Setup Page ================== [q] [w] [e] [r] P1 P1 P1 P1 Direction of Motion Speed Reach Time : : : : 0 3 100 0 [0=Forward, 1=Backward] [001..200km/h] [001..100%] [001..600x100ms, 0=endless] [t] [z] [u] [i] P2 P2 P2 P2 Direction of Motion Speed Reach Time : : : : 0 113 100 60 [0=Forward, 1=Backward] [001..200km/h] [001..100%] [001..
7 Declaration of Conformity for USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
7.1 FCC Label Figure 6: FCC Label PROPRIETARY The information contained in this document may be subject to change without notice. The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH. 2012-06-07_UserManual_EKTSDG.doc I Page 14 of 15 I June 7, 2012 www.smartmicro.
8 Contact Address: smart microwave sensors GmbH In den Waashainen 1 38108 Braunschweig Germany Phone / Fax numbers: Phone: Fax: +49-531-39023-0 +49-531-39023-599 Web / Email address: Web: Email: www.smartmicro.de info@smartmicro.de PROPRIETARY The information contained in this document may be subject to change without notice. The information contained in this document shall remain the sole exclusive property of s.m.s smart microwave sensors GmbH. 2012-06-07_UserManual_EKTSDG.