EN CONTENTS Contents 1 INTRODUCTION ................................................................................. 3 2 SAFETY INFORMATION ................................................................... 4 3 INSTALLATION MATERIAL.................................................................. 7 3.1 Kit supplied dishwasher (fully integrated)............................................ 8 3.2 Kit supplied dishwasher (integrated)....................................................
INTRODUCTION 1 EN INTRODUCTION Thank you for choosing one of our products. To install this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to installation of the appliance. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about installation of the dishwasher.
EN WARNINGS 2 SAFETY INFORMATION THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE.
WARNINGS EN CHECK THAT THE VOLTAGE, FREQUENCY AND PROTECTION OF THE DOMESTIC MAINS POWER SUPPLY MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE. TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISWASHER. DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERIALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE.
EN WARNINGS DO NOT OPERATE THE DISHWASHER UNLESS ALL THE OUTER PANELS HAVE BEEN POSITIONED CORRECTLY. IMMEDIATELY AFTER INSTALLATION, BRIEFLY TEST THE APPLIANCE FOLLOWING THE INSTRUCTIONS INDICATED BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. DO NOT ATTEMPT TO REPAIR THE APPLIANCE.
INSTALLATION INSTRUCTION EN 3 INSTALLATION MATERIAL To install the dishwasher correctly, the following materials are required: Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ phillips screwdriver ( rif. A Fig. 1); spirit level (rif. B Fig. 1); tape measure ( rif. C Fig. 1); compass saw ( rif. D Fig. 1); pencil ( rif. E Fig. 1); file (rif. F Fig. 1); 13mm open-ended whrench( rif. G Fig. 1); plumbing pliers ( rif. H Fig. 1); drill (rif. I Fig. 1); safety gloves ( rif . L Fig. 1). Fig.
INSTALLATION INSTRUCTION EN 3.1 Kit supplied with dishwasher (fully integrated) The kit supplied with the dishwasher comprises: • 1 adhesive steam guard or 1 steel steam guard (ref. A or B fig. 2)*; • 1 template for door panel (ref. C fig. 2); • 2 hooks for door panel (ref. D fig. 2); • 8 screws for securing the door panel hooks (ref. E fig. 2); • 2 screws for securing the door (ref. F fig. 2); • 2 screws for fixing the dishwasher to the adjacent walls (ref.G fig.2); • 2 screw caps (ref. H fig.2).
INSTALLATION INSTRUCTION 3.2 EN Kit supplied with dishwasher (integrated) The kit supplied with the dishwasher comprises: • 1 adhesive steam guard or 1 steel steam guard (ref. A or B fig. 2)*; • 1 template for door panel (ref. C fig.3); • 2 hooks for door panel (ref. D fig.3); • 8 screws for securing the door panel hooks (ref. E fig.3); • 2 screws for securing the door (ref. F fig.3); • 2 screws for fixing the dishwasher to the adjacent walls (ref. G fig.3); • 2 screw caps (ref. H fig.3).
INSTALLATION INSTRUCTION EN 4 DIMENSION OF DISHWASHER A height Integrated dishwasher 81.8 cm ÷ 88.8 cm Fig. 4 32-13/64"÷ 34-61/64" Integrated with steel door 86 cm ÷ 93 cm Fig. 4a 33-35/64"÷ 36-39/64" B width C depth 57 cm - 22-7/16" 59.7 cm ÷ 59.9 cm 23-1/2"÷ 23-37/64" Fully integrated 60 cm - 23-5/8" 55 cm - 21-21/32" Fig. 4b integrated Integrated with steel door Fig. 4 Fully integrated Fig. 4a Fig.
INSTALLATION INSTRUCTION 5 EN INSTALLATION AND HOOK-UP DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE. Remove the polystyrene rack blocks. Position the appliance in the chosen installation position. The sides and rear of the appliance can lie against kitchen units or walls. If the dishwasher is installed next to a heat source, separate it with a heat insulating panel in order to prevent overheating and malfunctions.
EN INSTALLATION INSTRUCTION 5.1 Leveling Level the appliance using the relative adjustable feet (e.g.: ref. A fig. 5); use an open-ended wrench to rotate the feet until the dishwasher is perfectly level. Some models are fitted with just one rear foot which can be adjusted with a screw located at the bottom front of the appliance (ref. A fig. 6); use a suitable Phillips screwdriver to turn the screw until the dishwasher is perfectly level. Use a spirit level to check the appliance is perfectly level (ref.
INSTALLATION INSTRUCTION EN 5.2 Connections Install the dishwasher so as to allow ease of access to the electrical and hydraulic connections through the adjacent unit. These connections must never be behind the dishwasher. The inlet and drain hoses can be pointed in all directions. make sure that they are not bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required direction. Figure 7 indicates the distances to maintain between the dishwasher and the various connections.
EN INSTALLATION INSTRUCTION 5.2.1 Connecting to the water supply PREVENTING THE RISK OF CLOGGING OR DAMAGE: IF THE WATER PIPE IS NEW OR HAS NOT BEEN USED FOR A LONG TIME, BEFORE CONNECTING TO THE WATER SUPPLY CHECK THAT THE WATER IS CLEAR AND FREE OF IMPURITIES, TO PREVENT DAMAGE TO THE APPLIANCE. THE DISHWASHER MUST ALWAYS BE CONNECTED TO THE WATER SYSTEM WITH NEW HOSES; OLD OR USED HOSES MUST NEVER BE REUSED. 5.2.1.
INSTALLATION INSTRUCTION EN Do not cut the inlet hose (see fig. 10). If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. Fig. 10 When connecting the dishwasher drain hose to the sink make sure that the hose is not bent (ref. A fig.
EN INSTALLATION INSTRUCTION 5.2.1.2 Connecting to a drain hose Insert the relative hose into a drain with a minimum diameter of 4 cm (1-37/64") (ref. A fig.12); alternatively, place the hose on the sink (ref. B fig. 11) using the supplied hose support (see fig.13), but taking care to avoid obstructions or excessive curving. Make sure the hose cannot fall out. For this purpose, the hose support is fi tted with a hole (ref. A fig. 13) which can be used to fi x it to the wall or the tap with a piece of string.
INSTALLATION INSTRUCTION EN Do not cut the inlet hose (see Fig. 14) If the hose is cut, the dihwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. Fig. 14 When connecting the dishwasher drain hose to the sink make sure that the hose is not bent (ref. A fig.
EN INSTALLATION INSTRUCTION Connecting to a «T» union of the drain circuit MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4 ") ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A Fig. 16) to the «T» union (ref. B Fig.16) of the drain circuit using a 38 mm to 50 mm (1-1/2" a 2") screw clamp* (ref.C fig 15); if necessary, cut the end of the dishwasher drain hose (ref. D Fig. 16) (do not cut the corrugate section).
INSTALLATION INSTRUCTION EN Connecting to a waste disposal unit with an air gap MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4 ") ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit ( ref. A Fig. 17). 2. Connect the dishwasher drain hose (ref. B Fig.17) to the air gap (ref.C Fig. 16) using the wide spring clamp (ref. D Fig. 17); if necessary, cut the end of the dishwasher drain hose (ref. E Fig.
EN INSTALLATION INSTRUCTION Connecting to the air gap (no waste disposal unit) IMAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4 ") ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A Fig. 18) to the air gap (ref. B Fig. 18) using the wide spring clamp(ref. C Fig. 18); if necessary, cut the end of the dishwasher drain hose (ref. D Fig. 18) (do not cut the corrugated section).
INSTALLATION INSTRUCTION EN Connecting to a waste disposal unit (no air gap) IMAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4 ") ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A Fig. 19 ). 2. Connect the dishwasher drain hose (ref. B Fig. 19) to the waste disposal unit inlet (ref. C Fig. 19), using the wide spring clamp (ref. D Fig. 19). D A B C Fig.
EN INSTALLATION INSTRUCTION 5.2.2 Electrical connections and warnings CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAMEPLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE. THIS APPLIANCE MUST BE GROUNDED.
INSTALLATION INSTRUCTION EN DO NOT CHANCE THE PLUG ATTACHED TO THE APPLIANCE. IF THE PLUG IS NOT SUITABLE FOR THE SOCKET, CALL IN A QUALIFIED ELECTRICIAN TO FIT A SUITABLE PLUG. THE PLUG AT THE END OF THE POWER CORD AND THE CORRESPONDING SOCKET MUST BE OF THE SAME TYPE AND MUST CONFORM TO CURRENT REGULATIONS GOVERNING ELECTRICAL APPLIANCES. THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION. NEVER REMOVE THE PLUG BY PULLING ON THE WIRE.
EN INSTALLATION INSTRUCTION Fig.21 Fig.22 Put the dishwasher into position, taking care not twist or crush the power cord or hoses (see Fig. 23). TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH THE DISHWASHER INTO PLACE. Fig.
INSTALLATION INSTRUCTION 5.3.2 EN Door panel assembly procedure (fully integrated) Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. A Fig. 24); mark the position of the door hooks with a pencil (see Fig. 24). Remove the template and use a drill with a suitable bit to make holes at the points marked on the panel. Fig.
EN INSTALLATION INSTRUCTION Drill holes for the panel handle using a drill with a suitable bit. Use the screw-driver to secure the door handle before hooking the panel to the dishwasher (see Fig. 26). N.B.: the screws are not supplied. Fig. 26 Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip into place (see Fig. 27) Fig.
INSTALLATION INSTRUCTION 5.3.3 EN Door panel assembly procedure (integrated) Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. A Fig. 28); mark the position of the door hooks with a pencil (see Fig. 28). Remove the template and use a drill with a suitable bit to make holes at the points marked on the panel. Fig. 28 Use the screwdriver to secure the door hooks with the 8 supplied screws (see Fig.
EN INSTALLATION INSTRUCTION If a gap is created between the control panel and the door panel (ref. A Fig.30), use the supplied strips (ref. B Fig.30) to fill it. The number of strips depends on the size of the gap. Fig.30 Position the strips between the control panel and the door panel of the dishwasher (ref. A Fig. 31) and fix them from under the control panel with the supplied screws (ref. B Fig. 31 ) using a screwdriver. Adjust the strips until a suitable compromise is reached. Fig.
INSTALLATION INSTRUCTION EN Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide upwards and slip into place (see Fig. 32). Fig.32 5.3.4 Door screwing Secure the door to the panel with the supplied screws. The panel must have a minimum tickness of 20mm (25/32") (see Fig. 33). Fig.
INSTALLATION INSTRUCTION EN 5.3.5 Completion of installation (if necessary, for all models) Make sure the dishwasher door, complete with panel, opens confortably and that the base plate (ref. A Fig. 34-35) does not prevent it from opening fully. If the base plate prevents the door from opening, mark out the section to remove (see Fig. 34-35), take out the base plate and cut it along the marking using a compass saw (see Fig. 36). Fig.35 Fig.34 Fig.
INSTALLATION INSTRUCTION EN Finish the cut with a file (see Fig. 37), in order to remove any burrs and/or imperfections. Put back the base plate (see Fig. 38) and try to open the dishwasher door fully; if the base plate still obstructs the door, repeat the above operations. Fig.37 Fig.
EN INSTALLATION INSTRUCTION 5.4 Apply the gaskets - Type A (the shape of the gaskets depends on the model) Before securing the dishwasher to the adjacent units, attach the gaskets to the sides. Remove the adhesive band on the gasket (see Fig. 39) Fig.39 Fix the gasket to the dishwasher, inserting it in the seat on the sides towards the front (see Fig.
INSTALLATION INSTRUCTION EN Fig.44 Fig.42 shows the state of the dishwasher after the above operations are performed. Fig.
INSTALLATION INSTRUCTION EN 5.5 Apply the gaskets - Type B (the shape of the gaskets depends on the model) Before securing the dishwasher to the adjacent units, attach the gaskets to the sides. Remove the adhesive band on the gasket (see Fig. 43) Fig.43 Fix the gasket to the dishwasher, inserting it in the seat on the sides towards the front (see Fig.
INSTALLATION INSTRUCTION EN Fig.45 Fig.46 shows the state of the dishwasher after the above operations are performed. Fig.
INSTALLATION INSTRUCTION EN Tighten the supplied screws with a screwdriver; this operation definitively fixes the dishwasher to the adjacent units; cover the side holes using the supplied plugs ( rif. A Fig.47 ). Fig.47 5.6 Testing After installation, test the dishwasher by starting a work cycle.