SAHP 7 Dryer
Please read this user manual first! Dear Customer, We hope that you get the best results from the product which has been manufactured in state-of-the-art plants and passed through a strict quality control procedure. Therefore, please read the entire user manual carefully before using the product and keep it as a reference for future use. In case of transferring the product to someone else, give the manual as well. The user manual will help you use your product in a fast and safe way.
1 Important safety instructions This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty. General safety • • • • • • • • • • • • Never place the product on a carpet-covered floor; otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product. Do not operate the product if the power cable / plug is damaged.
• • • • • • • • • • • • • • • • • accumulation around the exhaust exit and at adjacent areas. Power cable plug must be within easy reach after installation. Do not dry unwashed items in the dryer. Items soiled with cooking oils, acetone, alcohol, fuel oil, kerosene, stain removers, turpentine, paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer.
2 Installation Refer to the nearest Authorized Service Agent for installation of the product. To make the product ready for use, make sure that the electricity and water drainage system are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out. Preparation of the product's location as well as the electrical and waste water installations is under customer's responsibility.
Connecting the water drain hose 1. Pull hose in the product by hand in order to disconnect it from where it is connected. Do not use any tools to remove the hose. 2. Connect one end of the drain hose supplied separately with the product to the connection point from where you removed the hose of the product in previous step. 3. Connect the other end of the drain hose directly to the wastewater drain or to the washbasin. Hose must be fixed in every type of connection.
Warnings about sounds is normal to hear metallic noise from the C Itcompressor sometimes during operation. collected during operation is pumped to C Water water tank. It is normal to hear pumping noise during this process.
Technical specifications EN 2 Height (adjustable) 84,6 cm Width 59,5 cm Depth 59,8 cm Capacity (max.) 7 kg Weight (net) 51,5 kg Voltage Rated power input See type label Model code Type label is located behind the loading door.
3 Preparations for drying Things to be done for energy saving Following information will help you use the product in an ecological and energy-efficient manner. • Operate the product at a capacity suitable for the program you have selected and pay attention not to overload. • Spin your laundry at the highest speed possible when washing them. Thus, the drying time is shortened and energy consumption is reduced. • Dry the same type of laundry together.
that the washing machine allows on basis of the fabric type. Handkerchiefs (10 pieces) T-Shirts Correct load capacity Loading the laundry 1. 2. 3. A Follow the instructions in the “Programme selection and consumption table”. Do not load more than the capacity values stated in the table. It is not recommended to load the dryer with laundry exceeding the level indicated in the figure. Drying performance will degrade when the machine is overloaded. Furthermore, dryer and the laundry can get damaged.
4 Selecting a Programme and Operating Your Machine Control panel 1 9 2 8 7 4 3 5 6 1. Washing machine spin speed*/ Timer programme selection 6. Anti-creasing Prevents the laundry from creasing after the machine completes its programme. Spin speed used to spin the laundry in the washing macthine / Indicates the time for timer programs. 7. Dryness level Indicates the status of the machine. 8. Cancel audio warning 2. Display 3.
Preparing the machine 1. 2. 3. C obtain better results from your dryer, your C Tolaundry must be washed at suitable programmes Plug in your machine. Place the laundry in the machine. Press the “On/Off” button. Pressing the “On/Off” button does not necessarily mean that the programme has started. Press “Start/Pause/Cancel” button of the machine to start the programme. and spun at the recommended spin speeds in the washing machine.
•Timer programs You can select one of the 10 min., 20 min., 30 min., 40 min., 50 min., 60 min., 80 min., 100 min., 120 min., 140 min. and 160 min. timer programmes to achieve the desired final drying level at low temperatures. Programme dries at the selected time regardless of the drying temperature. Time display The display shows the time remaining for the programme to complete while a programme is running. Time is displayed in hours and minutes as “02:30”.
Programme selection and consumption table Programme table EN Programs 2 Capacity (kg) Spin speed in washing machine (rpm) Approximate amount of remaining humidity Drying time (minutes) Cottons / Coloreds A Extra dry 7 1000 % 60 175 A Cupboard dry 7 1000 % 60 156 A Iron dry 7 1000 % 60 125 Gentle 3 1000 % 60 80 Shirts 1.
Auxiliary function Audio Warning Cancel audio warning Audio warning level 1 Audio warning level 2 Audio warning level 3 Your dryer will give an audio warning when the programme comes to an end. If you do not want to hear this buzzing or want to change the volume level, you need to press the “Volume level” button. No audio warning will be given when “x” appears on the screen. You can select this function either before or after the programme starts. seconds.
Progress of programme Drying Iron Time delay With the “Time delay” function you can delay the programme start up to 24 hours. 1. Open the loading door and put the laundry in. 2. Set the drying programme and spin speed, and if required, select the auxiliary functions. 3. Press “Time delaying” buttons “+” and “-” to set the desired time delay. The time delay symbol will flash. 4. Press “Start/Pause/Cancel” button. Then the time delay starts to count down. The Time delay symbol lights up.
Adding/removing laundry in standby mode Ending the programme through canceling In order to add or take out laundry after the start-up of the programme; 1. Press the “Start/Pause/Cancel” button to switch the machine to “Pause” mode. Drying process will stop. 2. Open the door at Pause position and close it again after adding or taking out laundry. 3. Press “Start/Pause/Cancel” button to start the program.
5 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals. This product must be unplugged during maintenance and cleaning works (control panel, body, etc.). B Lint Filter / Loading Door Inner Surface Lint and fibres released from the laundry to the air during the drying cycle are collected in the Lint Filter. Cleaning the sensors fibre and lint are generally formed during C *Such wearing and washing.
Draining the water tank Dampness of the laundry is removed and condensed during drying process and the water that arise accumulates in the water tank. Drain the water tank after each drying cycle. Condensed water is not potable! Never remove the water tank when the programme is running! If you forget to drain the water tank, the machine will stop during the subsequent drying cycles when the water tank is full and the Water Tank warning symbol will flash.
5. Take out the filter drawer sponge. 6. Clean lint, fibre, and cotton raveling on the filter cloth by hand or with a soft piece of cloth. 9. 10. Place the filter drawer back into its place, turn the filter drawer cower clockwise making sure that it is closed securely. you notice a layer that may lead clogging C When on filter cloth, please clean the layer by washing 7. C 8. Close the filter drawer as to lock the red button. 11. Close the kick plate cover. in warm water.
Cleaning the evaporator Clean the lints accumulated on the fins of the evaporator located behind the filter drawer with a vacuum cleaner. can also clean by hand provided that you wear C You protective gloves. Do not attempt to clean with bare hands.
6 Troubleshooting Drying process takes too much time. • Pores of the lint filter are clogged. >>> Wash the lint filter with warm water. • Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer. • Ventilation grids on the front side of the machine are blocked. >>> Remove the objects (if any) that block ventilation in front of the ventilation grids. Ventilation is not sufficient since the room where the machine is installed is very small.
Lint Filter Cleaning symbol is flashing. • Filter housing is clogged with lints. >>> Clean the lint filter housing. • A deposit has built up on the lint filter pores that may cause clogging. >>> Wash the lint filter with warm water. • Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer. Water leaks from the loading door • Lint has accumulated on the inner surfaces of the loading door and on the surfaces of the loading door gasket.
