NFC Reader/Writer Operation Manual EXW1-NT1 P/N:CIR315C-01 FCC ID: 2AJE7SMC-WEX06 IC ID: 21344-WEX06 CAN ICES-3 (B)/NMB-3(B) U.S. Canada H - 26043 IFETEL:xxx-xxx Argentina Brazil Mexico UA.TR.
Indonesia Vietnam 総務省指定 R-R-OZK-NT1 EXW1-NT1 Made in China Korea 第 AC-20094 号 Japan Taiwan
Thank you for purchasing an SMC NFC Reader/Writer for SMC wireless system. Please read this manual carefully before operating the product and make sure you understand its capabilities and limitations. Please keep this manual handy for future reference. To obtain the operation manual about this product, please refer to the SMC website (URL https://www.smcworld.com) or contact SMC directly. Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
■Safety Instructions Warning ■Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. ■Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. ■Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
■Precautions for connecting the USB terminal of the NFC reader / writer ●Use the USB terminal at the back of the product for connecting the PC for the NFC reader / writer. Do not use the USB terminal on the front of the product. * It has been reported that the operation becomes unstable when the USB terminal on the side or the front of the PC is used depending on the type of the PC. ●Use a hub with power adapter when a USB hub is used.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal.
Contents of package Description Qty. NFC Reader/Writer 1 USB extension cable (2.95 m) 1 Operation Manual (this document) 1 Downloading and Installation of the driver software Windows OS has a general-purpose NFC reader/writer driver software installed. However, for the use of the SMC NFC reader / writer, please install the driver software in accordance with the procedure described in this document and operation manual before use.
● Installation of the driver software 〇 Windows 8.1 / Windows 10 When the PC is connected to the Internet, the driver software is automatically installed. Install the driver software again following the steps below. The Windows OS starts installation of the driver by connecting the EXW1-NT1 to the USB port of the PC. (1) Windows 8.1 / 10 displays the identified devices in the task bar at the bottom of the screen.
● Installation does not start automatically. (1) Download the driver software and manual referring to “Downloading of the driver software”. (2) Select language and press the “OK” button. (3) Screen below appears. Press the “Next (N)” button. (4) Screen below appears. Press the “Next (N)” button.
(5) Screen below appears. Press the “Install (I)” button. (6) The screen below appears and installation starts. Please wait. (7) The screen below appears when the installation is complete. * When the screen requires restarting of the PC, restart the PC. Press the「 Finish (F)」button.
# Check the operation of the NFC reader/ writer Check the operating condition of the LED of the NFC reader / writer referring to “Usage”. * The NFC reader/ writer is not displayed in the desktop or micro-computer even when it is correctly identified by the OS.
# SMC Wireless Communication System I/O Configurator (NFC version) The "I/O Configurator (NFC version)" can be used to check the parameter setting of the wireless unit and the contents and status of the constructed wireless system, using an NFC reader/writer and a PC. Refer to the product operation manual and "I/O Configurator (NFC version)" operation manual for details of the "I/O Configurator (NFC version)." (URL https://www.smcworld.
Fixing brackets Model Indication and Part Number To fix the NFC Reader/Writer onto a wireless unit and perform Read/Write, please purchase the following brackets External Fixing brackets Symbol NFC Reader/Writer xx ■EXW1-NT1-xx xx Contents For the following EX600-W models EX600-WEN1/2 EX600-WPN1/2 EX600-WSV1/2 For the EXW1 series ■EXW1-NT1-xx - As the brackets and the NFC Reader/Writer worsen the performance of wireless communication in the 2.
Contacts AUSTRIA (43) 2262 62 280 Girakstrasse 8, AT-2100 Korneuburg, Austria BELGIUM (32) 03 355 1464 Temesselei 232, 2160 Wommelgem, Belgium BULGARIA (359) 2 9744492 Business Park Sofia, Building 8c, 6th floor, BG-1766 Sofia, Bulgaria CROATIA (385) 1 370 72 88 Zagrebačka Avenija 104, HR-10000 Zagreb, Croatia CZECH REP.
NORWAY (47) 67 12 90 20 Vollsveien 13 C, Granfos Næringspark N-1366 Lysaker, Norway POLAND (48) 22 211 96 00 ul.