User's Manual

Page 1
8/17/10
SMCWF01-Z 08172010
SMCWF01-Z Key Fob Quick Start Guide
1 Pre-Installation Guidelines
A. Holding the key fob in one
hand, carefully insert the
tip of a flat-head
screwdriver into the casing
seam.
B. Push lightly and twist the
screwdriver handle.
C. Find the supplied CR2032 3-
volt lithium battery.
D. Remove the circuit board
and rubber button pad from
the key fob casing.
E. Place the rubber button pad
on the circuit board so the shield
icon is nearest the beveled end of
the circuit board.
F. Hold down the center button
and any other button while slowly
inserting the battery in the battery
slot (positive side away from the
circuit board).
G. When the LED flashes green,
release the buttons immediately.
The LED flashes green three times every five seconds.
The device is defaulted and in Search mode. The key fob
is now ready to be added to the TouchScreen.
H. Replace the circuit board in the key fob casing.
2
I
Adding a Key Fob
. From the Home screen, touch the Settings widget.
J. When the Keypad screen appears, touch the numbers
enter your keypad code.
to
K. When the Settings menu appears, use the keypad to
enter the Installer Code (this code is the same for all
TouchScreens installed by your company).
When the Technician keyboard pad appears, enter your
Technician ID an
L.
d touch Done.
M. When the Technician Settings menu appears, select Key
Fobs & Pads > Add a Key Fob. The Locating Key Fobs
screen appears.
N. Touch Next . The system scans the premises for key
that can be added. Key fobs must meet the followin
fobs
g
requirements:
- Defaulted
- Not currently paired with another TouchScreen.
Follow the system prompts to complete the add process
O.
and pair the key fob with the TouchScreen.
P. When the system finds the key fob, press
center
and hold the
button to pair it with the TouchScreen.
Key
Q. Press and hold the Arm Away or Arm Stay
buttons to test the key fob’s connectivity
to the TouchScreen.
Note: If no available key fobs are found or
fewer are found than expected touch Cancel
Fob Add to return to the Technician
Settings menu.
3 Deleting a Key Fob
Congratulations on purchasing your SMC
W
F01-Z Key Fob.
The SMCMT02-Z Key Fob is a professional state-of-the-art device that allows you to arm and disarm your system from anywhere within or just outside your home. Disarming your security
system with your key fob does not skip the Entry Delay period and does not require entering a key pad code. The SMCMT02-Z also provides an emergency alarm function anywhere within
range of the TouchScreen.
Deleting a key fob from the premises removes it from being
used to perform actions in your security system. You should
delete a key fob:
¾ If the key fob is being relinquished by the customer.
¾ To reset the key fob to factory default settings by
deleting the key fob and re-adding it to the TouchScreen
immediately.
To delete a key fob from the TouchScreen:
A. Perform steps A through D in step 2, “Adding a Key Fob
to the TouchScreen”.
B. When the Technician Settings menu appears, select Key
Fobs & Pads > Delete a Key Fob. The Remove Key Fob
screen appears.
C. Touch the key fob icon that you want to delete.
D. When a confirmation dialog appears, touch Yes to delete
the key fob from the TouchScreen.
E. After deleting the key fob from the TouchScreen, press
the
button on the key fob to reset the device to
default and place it in Search mode so it can be added
to a TouchScreen again.
Congratulations!
You have successfully your added key fobs.

continued on next page