KP2 PRO INSTALLATION GUIDE DISTRACTION DETECTED Version 5.
KP2 PRO INSTALLATION GUIDE EVENT TRIGGER TABLE OF CONTENTS Please follow along with this guide for details on proper device installation and calibration. PACKAGE CONTENTS .................................................................... 3 HOW TO CALIBRATE YOUR G-SENSOR ...................................10 KP2 FEATURE REFERENCE ............................................................4 HOW TO CONFIGURE KP2 SETTINGS...................................... 11 HOW TO INSTALL YOUR KP2 ...............
PACKAGE CONTENTS KP2 Vehicle Recorder Mounting Bracket & Attached Power Cable (Connects to Adapter Cables) Removable Wedge Block (Driver-Facing Camera Ordered Separately) Torx® Wrench *64GB MicroSD Card (Pre-Installed) 8" 3-Wire Adapter Cable (Connects to Bracket Cable) Square Adhesive Cable Clips (x5) *128GB MicroSD Available Upon Request Nano SIM Card (Pre-Installed) Double-Sided 3M™ Tape (One Adhered to Bracket, One Extra Piece) Alcohol Prep Pad (x2) SMARTWITNESS KP2 PRO INSTALLATION GUIDE 3
KP2 FEATURE REFERENCE Camera Lens FRONT Lens Angle Lock Windshield Bracket SIDE Unscrew the right-side bracket. Remove the KP2 from the bracket to adjust camera angle or insert/remove SIM/SD card. Applied screws for design purpose only.
KP2 FEATURE REFERENCE SIDE COVER OPEN Release Tab Nano SIM Slot (4FF) Micro SD Card Slot Memory SD Card Slot 2nd Camera (Model: KP2-DFC) BACK Ecall/Panic Button Bluetooth Pairing Button LED Types: Warning LED (RED) Record LED (BLUE) Network LED (GREEN) SMARTWITNESS KP2 PRO INSTALLATION GUIDE 5
HOW TO INSTALL YOUR KP2 Prepare Your KP2 DISCLAIMER The KP2 installation featured in this guide is designed for professional installation. SmartWitness assumes installers possess knowledge of current, generally accepted industry installation standards and practices. 1. Use the Torx® wrench provided in the package contents to open the side cover of the device. You’ll notice that both the microSD and SIM cards come pre-installed. See Diagram A. 2. Keep the side panel open.
HOW TO INSTALL YOUR KP2 Attach Your Camera to the Windshield Your vehicle’s windshield temperature shouldn’t be too hot or cold. SmartWitness recommends installing your KP2 in moderate temperatures (10°C~27°C). If in severe cold weather, use the vehicle defrosters to warm and dry out the windshield. Ensure your windshield is dry and has no chips or cracks before installation. If the windshield is compromised, device application may cause chips or cracks to spread. 1.
HOW TO INSTALL YOUR KP2 Connect the KP2 to Your Vehicle’s Power Source If you are not a professional technician, click here to request installation from an approved SmartWitness installer. By continuing this process without a certified installer, you accept the ramifications of tampering with your vehicle’s power source. 1. Turn off your vehicle. 2. Take your main power cable, and place it where it’ll reside alongside the vehicle’s headliner and A-pillar.
HOW TO TEST YOUR INSTALLATION After installing the KP2 in your vehicle, test whether it is operational. 1. Turn on your vehicle. Your camera should power on. 2. You’ll see a Red/Blue/Green light sequence during your camera’s boot-up process (see LED Reference Table). 3. After your camera completes the boot-up process, check for a solid Blue light. This indicates proper operation and recording. 4. Check for a Green light that remains on, indicating connectivity. 5. Watch for a Blue light.
HOW TO CALIBRATE YOUR G-SENSOR Park your vehicle on a flat surface for calibration. After your camera boots up, press the G-sensor calibration button. This is the small black button to the right of the e-call/panic button. You’ll hear a beep, and the KP2 LED light will blink briefly to indicate that the G-sensor calibration has registered. You’ve completed the first steps of your KP2 installation. To adjust your settings, continue to How to Configure KP2 Settings.
HOW TO CONFIGURE KP2 SETTINGS Access KP2 Installation App To finalize your installation and onboard your device, scan the QR code. Download and open the app. Scan your device’s IMEI label, and follow the walk-through featured below. 1. Ensure the IMEI code in the app matches your device’s IMEI. If there isn’t a match, tap No and contact SmartWitness support. If there’s a match, tap Yes to continue. 2. Read the instructions to understand more about your vehicle’s “Horizon” and “Hood” lines.
COMPLETE YOUR INSTALLATION/SUPPORT You’ve finished your KP2 installation and device calibration. Your KP2 is ready to go. If you have any complications during the installation process or have any questions, please contact our support team at support@smartwitness.com or call us.
LED & BUZZER SPECIFICATIONS LED Warning Status/Step Red Startup & Power Off Off - Booting Step 2 On On and Off Off - Booting Step 3 On On On and Off - Booting Finished On On On - Power Off Off Fast Simultaneous On and Off Continuous Record Off Off Off - Recording - On - - Standby - On - - Recording - Fast On and Off - - - On - - Event Recording - Fast On and Off - - - Off - - 4G LTE Network Device Ready - - On - Communication - - On - SD For
TECHNICAL SPECIFICATIONS NAME VALUE Image Sensor 2 Megapixel CMOS Sensor G-Sensor Internal 3-Axis G-Sensor Main, Road-Facing Camera (Forward-Facing): 140° (115°(H), 60°(V)) Gyro 3 Axis (X, Y, Z), Output Rate: 100Hz 2nd Camera (Optional, Driver-Facing): 130° (104°(H) x 56°(V)) Time GPS Time Sync + Built-In Real-Time Clock (RTC) ADAS Event Types - Headway Monitoring Warning (Tailgating) - Forward Collision Warning - Lane Departure Warning Speaker Audible Alerts for Events and Audio for ADAS an
© 2022 SmartWitness. All Rights Reserved.