Alarm System User Guide 1
Overview The hub Wi-Fi model is an alarm system that utilizes Wi-Fi 802.11 b/g/n(2.4GHz). All sensors are wirelessly connected to the hub. In the event of alarm activation, for example, when a sensor is triggered, a push notification will be sent and an alarm call will be made automatically to all registered users. The system can be controlled on-site by the remote tag supplied, or remotely from anywhere with SmartLife or Tuya APP.
At a Glance Hub 3 1 2 1. 2. 3. 4. 5. Configuration button Indicator x2 Siren port Power port ( Micro USB ) Battery on/off switch Note: The MICRO SIM slot and MIC hole are not available.
Remote tag 1. 2. 3. 4. Arm button Disarm button Home arm button Panic button 1 Door/window sensor 1. 2. 3. 4. 5. 6. 7.
Indicators What you see Blinking blue Blinking purple Blinking red Blinking cyan Solid green Solid cyan Nothing What it means Wi-Fi connection configuration in Smart Mode @ quickly, in AP Mode @ slowly Pairing/sniffer mode Alarming Somebody visit (Doorbell) Armed Home armed Disarmed Pl Placement/Installation It is advised to install the hub over the ground more than 50 cm, do not install the hub at the corner, because this will affect WiFi and RF signal reception.
off the hub. Connect the power cord to the USB port and plug the power adapter into the outlet to power on your hub, then slide the battery switch to on. Door/Window Sensor Install the detector on the door case (window frame), and attach the magnet to the moving part of the door (window) to the alignment mark of the detector. The magnet should be aligned with the middle of detector and placed within 0.6 inches (1.5cm) away from the detector when the door or window is closed.
signal separately .Step.2 Power on the hub Step.3 Long press the wi-fi configuration button until the blue light blinking fast.
Step.4 Open the “ smartlife” app and click “add device” or “+” Step.
Step.6 Connect the hub to the 2.4GHz WiFi.Then wait for connecting successfully. Accessory Pairing The wireless accessories supplied with this kit are paired with the hub. IF NOT or you want to pair more, you might easily pair wireless accessories with your hub as follows. At your device home page in APP tap Accessories > +, or click configuration button three times on your hub, then the hub goes into the pairing/sniffer mode with indicators blinking blue.
How to pairing accessories To Do like this before the hub sniffer countdown expires Add a door sensor Open the back cover of the sensor, and switch on the button. Start with the door sensor and magnet closely aligned, then separate or click the button on the door sensor until the blue light comes on. Add remote Press any button on your remote Tips: up to 20 wireless detectors and 10 remote tags can be added.
Using Security System Arm/Disarm You can arm and disarm your home using the remote tag or APP. Tap Tap Tap Tap to Away arm. to Homel arm. to Disarm. to trigger an emergency alarm. Change Settings via APP Timer To edit the schedules for arming/disarming your system automatically at a daily time. Exit delay Exit Delay allows you to leave your home once you’ve armed the security system. When you place the system into Away Arm Mode, it makes a count down tick to let you know that it is preparing to arm.
a short time until your alarm goes off. When you hear this, you should disarm your system as soon as possible. You can adjust the countdown timing from 0 to 299 seconds. Alarm duration Adjust alarm sound duration from 1 to 59 minutes. Sensor low battery alarm Enable to receive notification when the wireless accessory is low battery. Countdown with tick tone Turn countdown tick tone on or off when the hub is during Exit Delay or Entry Delay.
Normal: Sensors set to Normal Zone are activated in Arm (full arm) or HOME Mode (home/stay/partial arm). We recommend setting door/window sensor to Normal Zone. 24 Hours: Sensors set to 24H Zone will activate the alarm and sounding when triggered, regardless of the alarm status (Armed or Disarmed). Delay: If sensors set to Delay Zone are triggered, the Hub will sound the alarm after the delay time passed. We recommend setting door sensors with a delay if they are used as primary entryways.
Remote Power Supply: DC 3V (CR2025 Lithium Battery x1) Standby Current: <5uA Transmitting Distance: <80m (Without obstacles and no Interference) Radio Frequency: 433Mhz Operation Temperature: -10~55℃ Door/Window Sensor Power Supply: DC 3V (CR2032 Lithium Battery x1) Standby Current: <8uA Transmitting Distance: <80m (Without obstacles and no Interference) Radio Frequency: 433Mhz Operation Temperature: -10~55℃ Siren INPUT: 3~15VDC/500mA Sound Level: 125dB 14
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.