Instruction Manual WIRELESS WEATHER STATION Model: SC93 TIME Moon Phase In&Out Temp In&Out Humidity Adjustable Backlit Dual Alarms Weather Forecast °C/°F Switchable Snooze Function DST Function
Content 1. Preface 2. Attention 3. Package Content 4. Product Specification 4.1 Color Weather Station 4.2 Wireless Remote Sensor 5. Know Your Device 5.1 Screen 5.2 Buttons 5.3 Wireless Remote Sensor 6. Preparation 7. Initial Time Setup 8. Dual Alarm Setting 8.1 Alarm Setting 8.2 How to Turn on/off the Alarms 8.3 How to Check the Alarms 8.4 Turn off the Alarm Tone 8.5 Snooze Function 9. Weather Station and Remote Sensor Pairing & Manual Signal Reception 9.
1. Preface Thank you for choosing this weather station from SMARTRO. Before Use ● Make sure to read the instruction manual carefully. This information will help you to familiarize yourself with your new device, to learn all of its functions and get advice in the event of problems. ● Following the instructions will prevent damage to your device. ● We shall not be liable for any damage that occurs as a result of not following these instructions. ● Please keep this instruction manual for future reference.
4. Product Specification 4.
5. Know Your Device 5.
5.
5.3 Wireless Remote Sensor SC93 C8 WIRELESS SENSOR C1 CH1 C2 C3 C4 C1: Temperature C2: Humidity C3: Transmission signal light C4: "°C/°F" switch button C5: "TX" button C6: Channel switch knob C7: Battery compartment C8: Wall-mount hole 5 TX 1 2 3 AA (UM-3)1. 5V C6 C/F AA (UM-3)1.
6. Preparation ● Open weather station battery compartment cover, insert 2 x AA batteries, ensure correct battery polarities [ "+" and "–" ] and connect the DC adapter to power the weather station. ● The screen will light up, and the device will make a beeping sound. The weather station will start to detect indoor temperature and humidity. ● Open the wireless remote sensor battery compartment cover. Choose the same channel as the weather station through the numbered knob.
● The PRESSURE value will be flashing, press "▲" or "▼" to set the correct pressure and press " " to confirm. icon. Press " " to confirm and to end up the time setting. ● The WEATHER icon will be flashing, press "▲" or "▼" to set the current weather Note: ● During the setup, if you want to exit, double click " " button. If there is no operation of buttons within 20 seconds, the weather station will save the current settings and automatically return to the normal display.
Note: ● During the alarm setting, double clicking " " or not operating any buttons within 20 seconds will cause the weather station to save the current settings and automatically return to the normal display. ● The snooze time can be set from 5 ~ 60MIN. It can also be deactivated by setting it to OFF. ● For quick setting of the values, long press "▲" or "▼". 8.
9. Weather Station and Remote Sensor Pairing & Manual Signal Reception 9.1 Weather Station and Remote Sensor Pairing Step 1: — Insert 2 x AA batteries in the weather station and connect it with the adapter. — Insert 2 x AA batteries in the remote sensor. Step 2: — Select a channel for the remote sensor through the numbered knob (1, 2, and 3). The indicator will light up once to indicate that the wireless remote sensor is sending out signals.
- Please ensure that the channels of the weather station and sensor are the same. - Long press " " button to receive signals manually. A flashing RF antenna symbol will be displayed beside the channel. This means that the weather station is in a receiving state. - Press "TX" button on the wireless remote sensor to send out signals manually, a red light will flash. 9.
10. Temperature & Humidity 10.1 How to Set Temperature Alert ● Firstly choose a channel you want to set the outdoor temperature and humidity alert on, then press " column. ● Press and hold " alert setting. " to activate the alert, " " will be displayed in the ALERT " button for 2 seconds to enter the temperature and humidity ● The highest outdoor temperature and " " will be flashing.
10.2 Frost Point Alert When the outdoor temperature reaches +30.2°F (-1.0°C) ~ +37.3°F (+2.9°C), the frost alert will be automatically activated and the icon " " will be flashing. 10.3 Comfort Indicator & Mold Risk ● Indoor comfort level is generated based on the indoor temperature and humidity, there are 5 levels as follows: Comfortable too cold or too hot ● The mold risk level is generated based on the indoor temperature and humidity.
11. Weather Forecast 11.1 Weather Forecast Statement ● The weather station calculates the weather forecast based on the historical recorded barometric pressure where you are located. ● The weather forecast cannot be compared with the professional weather services supported by satellites and high-performance computers. ● If the weather information on the device is different from the local weather forecasting service, please take the advice of the latter as authoritative. 11.
13. Air Pressure The barometric pressure updates every hour. The weather station will record the pressure of the last 3, 6, 9, 12, 18, 24 hours and compare it with the current barometric pressure to generate a histogram. 14. Backlight & Night Mode 14.1 Backlight Setting — When connecting the weather station with the DC adapter, the backlight will remain on. The backlight has 5 brightness levels for selection: level 1, level 2, level 3, level 4 and OFF.
● The minute of the exit time of night mode will be flashing, press "▲" or "▼" to set the required minute and press " " to confirm. After completing these steps the weather station will return to the original display. Note: ● When night mode is on, the icon " " will be displayed on the screen.
16. Low Battery ● If the battery icon " " is displayed in the "INDOOR" column, it means that the weather station batteries are running out. Please replace the batteries as soon as possible. ● If the battery icon " " displays in the "OUTDOOR" column, it means that the remote sensor batteries are running out. Please replace the batteries as soon as possible. 17. Troubleshooting PROBLEM CAUSE SOLUTION 1. Press " activate the backlight for 15 seconds. batteries.
The device has some The indoor and outdoor readings are different when putting the two devices together. tolerance. Temperature range in 32°F~104°F(0-40°C), tolerance:±1.8°F. Other: ±3.6°F. Humidity range in If the difference is beyond the range, please please contact after-sales support at: support@smartro.co. 40%~80%, tolerance: ±5%. Other: ±8%. The time alarm function is activated. The alarm rings unexpectedly at night. Please check if the alarms are set correctly or turn them off.
19. Waste Disposal ● This product is manufactured with high-grade materials and components which can be recycled and reused. ● As a consumer, you are legally required to take them to your retail store or an appropriate collection site depending on national or local regulations in order to protect the environment. ● The symbols for the heavy metals contained are: Cd=cadmium, Hg=mercury, Pb=lead. ● Please do not dispose of this instrument in household waste.
Appendix 1: City Code of the United States Country United States(US) 19 City Abbr Washington DC No.
Buffalo BUF 201 Richmond RMD 202 Columbia COL 203 Little Rock LRC 204 Columbus CLS 205 Grand Rapids GRS 206 Salt Lake City SLC 207 Providence PVD 208 Manchester (NH) MNH 209 San Diego SDG 210 Santa Fe SFE 211 Bismarck BIS 212 Reno REN 213 New Haven NHV 214 Baltimore BAL 215 South Carolina (SC) SCR 216 Savannah SAV 217 20
Appendix 2: City Code of other Countries Country Germany(DE) Austria(AT) Belgium(BE) Bosnia & Herzegovina(BA) Abbr No. City Abbr Berlin BER Bremen BRE Köln Dortmund No.
Greece(GR) Athens AHN 69 Hungary(HU) Budapest BUD 70 Ireland(IE) Dublin DUB 71 Ancona ANC 72 Naples NAP 82 Bari BAR 73 Palermo PAL 83 Bolzano BOZ 74 Parma PRM 84 Cagliari CAG 75 Perugia PEG 85 Florence FIR 76 Rome ROM 86 Foggia FOG 77 San Remo SRE 87 Genoa GEN 78 Triest TRI 88 Italy (IT) Lecce LEC 79 Turin TUR 89 Messina MES 80 Venice VEN 90 Milan MIL 81 Verona VER 91 Liechtenstein(LI) Vaduz VDZ 92 Luxemburg(LU) Luxembourg LUX 9
Sweden(SE) Switzerland (CH) United Kingdom(GB) Lithuania(LT) Gothenburg GOT 138 Karlstad KAR 139 STO 140 146 Basel BAS 141 Lugano LUG Berne BNE 142 Sion SIO 147 Chur CHU 143 St.
: +1(323)287-5798 : support@smartro.co : http://bit.ly/smartro_01 : smartro_01 : https://www.smartro.
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.