501 SE Columbia Shores Boulevard, Suite 500 Vancouver, Washington 98661 USA +1 360 859 1780 / smartrg.com / Gateway User Manual Model: SR700ac Release 1.
Table of Contents Welcome! Purpose & Scope Intended Audience Getting Assistance Copyright and Trademarks Disclaimer Getting Familiar with your Gateway LED Status Indicators Connections DSL WAN LAN USB POWER External Buttons WPS Button WiFi or WLAN Button Reset Button Installing your SR700ac Gateway Logging into your Gateway's UI Device Info Summary WAN Statistics LAN WAN Service xTM xDSL References Route ARP DHCP CPU & Memory Advanced Setup Layer2 Interface ATM Interface PTM Interface ETH Interface WAN Ser
Table of Contents System Log Security Log SNMP Agent Management Server TR-069 Client STUN Config Internet Time Access Control Accounts Add an Account Modify or Delete an Account Default Passwords Services Passwords Access List Logout Timer Update Software Reboot Logging Out Appendix: Compliance Statements FCC Interference Statement FCC Radiation Exposure Statement FCC - PART 68 Ringer Equivalency Number Statement IC CS-03 statement Canada Statement 5GHz Revision History 122 124 125 126 126 129 131 132 133
Welcome! Thank you for purchasing this SmartRG product. SmartRG offers solutions that simplify the complex Internet ecosystem. Our solutions include hardware, software, applications, enhanced network insights, and security delivered via a future-proof operating system. Based in the USA, SmartRG provides local, proactive software development and customer support. We proudly offer the best, most innovative broadband gateways available. Learn more at www.SmartRG.com.
Disclaimer SmartRG does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor patent rights of others. SmartRG further reserves the right to make changes to any products described herein without notice. This publication is subject to change without notice. Any trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners.
Getting Familiar with your Gateway This section contains a quick description of the Gateway's lights, ports, and buttons. SmartRG produces several models that vary slightly in capabilities (See Appendix B for details) but the basic scheme of lights, ports and buttons represented in this section exists on each model. LED Status Indicators Your SmartRG gateway has several indicator lights (LEDs) on its exterior. The following table explains the actions of the LEDs located on the front of the SR700ac gateway.
Connections Below is a generic representation of a SmartRG gateway, Your specific model may have more or fewer ports and controls. Refer to the Quick Start Guide enclosed with your gateway for specifics regarding installation of your particular model. The ports depicted in this example are described below. DSL The grey RJ12 port labeled DSL is specifically intended for connection to an internet provider via a DSL (Digital Subscriber Line) service. The center pair carries the first DSL line.
For models with a stand-alone, RJ45, WAN port and a DSL port, the WAN port can be re-purposed to function as an additional LAN port when your internet connection is via DSL. For instructions to enable this SmartPortTM feature, see the Ethernet Configuration section in this manual. LAN The four (yellow) RJ45 ports across the back of your gateway labeled LAN1, LAN2, LAN3, LAN4 are the means to connect client devices such as computers and printers to your gateway.
WiFi or WLAN Button The button labeled WiFi or WLAN (depending on model) toggles the WiFi radio on and off. The WLAN LED indicator on the gateway displays the current state of the Wi-Fi radio. This button is located on the top of the gateway. To activate the Wi-Fi radio, press and hold the WiFi (WLAN) button for 3-5 seconds and then release. Expect a 1-3 second delay before the WiFi (WLAN) LED turns on. Repeat this step to deactivate the Wi-Fi radio.
3. For all models, enter the default username and password (usually admin/admin) and click Login or OK to display the default landing page. For many models, this is the Device Info page. Note: The gateway's UI can be accessed via the WAN connection by entering the WAN IP address in your browser's address bar and entering the default username and password: support/support. WAN HTTP access control MUST be enabled to access the gateway's UI via the WAN connection.
Device Info There are several selections under Device Info in the left navigation bar. Each of them shows a different element of the gateway's setup, status or nature of its connection with the provider and also with LAN devices. Device Info pages are read-only. You cannot interact with or change the settings in this section. Summary When you log into the gateway interface, the Device Info summary page is the first to appear.
WAN On this page, you can view information about the connection between your ISP and your gateway. The WAN interface can be DSL or Ethernet and supports a number of Layer 2 and above configuration options (explained later in this document). Some features are supported only on specific SmartRG models. Those exceptions are specified in this guide. In the left navigation bar, click Device Info > WAN. The following page appears. The fields on this page are explained in the following table.
Statistics In this section, you can view network interface information for LAN, WAN Service, xTM and xDSL. All data is updated in 15-minute intervals. LAN On this page, you can view the received and transmitted bytes, packets, errors and drops for each LAN interface configured on your gateway. All local LAN Ethernet ports, Ethernet WAN ports and wireless Interfaces are included. For some models, statistics are provided for multicast, unicast and broadcast traffic.
WAN Service On this page, you can view the received and transmitted bytes, packets, errors and drops for each WAN interface for your SmartRG Gateway. All WAN interfaces configured for your gateway are included. In the left navigation bar, click Device Info > Statistics > WAN Service. The Statistics -- WAN page appears where you can view detailed information about the status of your WAN. To reset the counters, click Reset Statistics near the bottom of the page.
The fields on this page are explained in the following table. Field Name Description Port Number Statistics for Port 1, or both ports if bonded. In Octets Total quantity of received octets. Out Octets Total quantity of transmitted octets. In Packets Total quantity of received packets. Out Packets Total quantity of transmitted packets. In OAM Cells Total quantity of received OAM cells. Out OAM Cells Total quantity of transmitted OAM cells. In ASM Cells Total quantity of received ASM cells.
xDSL On this page, you can view the DSL statistics for your gateway. All xDSL (VDSL or ADSL) interfaces configured for your SmartRG gateway are included. The terms and their explanations are derived from the relevant ITU-T standards and referenced accordingly. 1. In the left navigation bar, click Device Info > Statistics > xDSL. The Statistics - xDSL page appears. 2. To run an xDSL Bit Error Rate (BER) test (to determine the quality of the xDSL connection): a.
3. To reset the counters, click Reset Statistics at the bottom of the page. The fields on this page are explained in the following table. Field Name Description Mode xDSL mode that the modem has trained under, such as ADSL2+, G.DMT, etc. Traffic Type Connection type. Options are: ATM, PTM and ETH. Status Status of the connection. Options are: Up, Disabled, NoSignal , and Initializing. Link Power State Current link power management state (e.g., L0, L2, L3).
Field Name Description tiple bit error, and therefore, HEC Error Correction is not performed. [1],[2] OCD Errors Total number of Out-of-Cell Delineation errors. ATM Cell delineation is the process which allows identification of the cell boundaries. The HEC field is used to achieve cell delineation. [4] An OCD Error is counted when the cell delineation process transitions from the SYNC state to the HUNT state. [2] LCD Errors Total number of Loss of Cell Delineation errors.
The fields on this page are explained in the following table. Field Description Destination Destination IP addresses. Gateway Gateway IP address. Subnet Mask Subnet Masks. Flag Status of the flags. Metric Number of hops required to reach the default gateway. Service Service type. Interface WAN/LAN interface. Next Hop (For IPv6 Route only) Next hop IP address.
The fields on this page are explained in the following table. Field Name Description IP address The IP address of the host. Flags Each entry in the ARP cache will be marked with one of these flags. Options are: Complete, Permanent, and Published. HW Address The hardware (MAC) address of the host. Device The system level interface by which the host is connected. Options are: br(n), atm(n), eth(n), and atm(n).
Field Name Description Hostname The host name of each connected LAN device. MAC Address The MAC Address for each connected LAN device. IP Address The IP Address for each connected LAN device. Expires In The time until the DHCP lease expires for each LAN device. CPU & Memory On this page, you can view the CPU and memory data for the gateway. In the left navigation bar, click Device Info > CPU & Memory. The following page appears, showing the current usage and history.
ATM Interface On this page, you can configure Asynchronous Transfer Mode / Permanent Virtual Conduit (ATM/PVC) settings for your gateway. You can customize latency options, link type, encapsulation mode and more. Note: Devices (routers) on both ends of the connection must support ATM / PVC. 1. In the left navigation bar, click Advanced Setup > Layer2 Interface > ATM Interface and then click Add. The following page appears. 2.
Field Name Description ATM path. This setting works with the VCI. Each individual DSL circuit must have a unique VPI/VCI combination. String limits are: 0-255. VCI Enter a Virtual Channel Identifier. A VCI is a 16-bit identifier that has a unique channel. Options are: 32-65535. Select DSL Latency Select the level of DSL latency. Options are: l Path0 Fast: No error correction and can provide lower latency on error free lines. l l Select Link Type Encapsulation Mode l EoA: Ethernet over ATM.
Field Name Description Scheduler for Queues of Equal Precedence as the Default Queue The algorithm used to schedule the queue behavior. VC scheduling is unique from Default Queues. Options are: l WRR: Weighted Round Robin packets are accessed in a round robin style and classes can be given. l l l WFQ: Weighted Fair Queuing packets are assigned in a specific queue. Default Queue Weight: The default weight of the specified queue. Options are: 163.
Field Name Description Select DSL Latency Select the level of DSL latency. Options are: l Path0 Fast: No error correction and can provide lower latency on error-free lines. l Path1 Interleaved: Error checking that provides error-free data which increases latency. Select Scheduler for Select an algorithm for applying queue data priority.
3. If a WAN port is already configured or you clicked Add, the following page appears. Note: If a WAN port it is already configured, you must remove it before you can define a new one. Before you can remove the existing port, you must first modify or delete any WAN service that uses it. The Add button does not appear until the existing port is removed. 4. Select the LAN port you wish to act as a WAN port. 5. Click Apply/Save to commit your changes. 6.
WAN Service In this section, you can configure WAN services for: l "xPPP over Ethernet" l "IP over Ethernet" l "Bridging" A sample configuration scenario is provided for each variation. xPPP over Ethernet There are several parts to configuring a PPP over Ethernet WAN service. You will progress through several pages to complete the configuration. 1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears. 2.
3. Click Next. The following page appears. 4. Accept the default of PPP over Ethernet (PPPoE) WAN service type. 5. Modify the other settings as needed. The fields on this page are explained in the following table. Field Name Description Enter Service Description Enter a name to describe this configuration. Enter 802.1P Priority Options are 0 - 7. The default is 0. For tagged service, enter values in this field and the 802.1Q VLAN ID field.
Field Name Description Internet Protocol Selection Different scheduling priorities can be applied to statistically multiplexed data flows. Since each data flow has its own queue, an ill-behaved flow (which has sent larger packets or more packets per second than the others) will only punish itself and not other sessions. Options are IPv4 Only, IPv4&IPv6 (Dual Stack), and IPv6 Only. Note: When you select IPV4&IPV6 or IPV6, the subsequent options presented will change accordingly. 6. Click Next.
7. Modify the fields as needed. The fields on this page are explained in the following table. Field Name Description PPP Username Enter the username required for authentication to the PPP server. PPP Password Enter the password required for authentication to the PPP server. PPPoE Service Name (Optional) Enter a description for this service. Authentication Method Select a means for authentication. Options are: l AUTO: Attempt to automatically detect handshake protocols (listed below).
Field Name Description Enable PPP Debug Mode Select to have the system put more PPP connection information into the system log of the device. This is for debugging errors and not for normal usage. Bridge PPPoE Frames Between WAN and Local Ports Select to enable PPPoE passthrough to relay PPPoE connections from behind the modem. Also known as Half-Bridged mode. Enable Firewall This option enables functions in the Security sub-menu and is enabled by default. Click the checkbox to disable this option.
9. Click the arrows to move your selection from left to right or from right to left. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
10. Click Next. The following page appears where you will select DNS Server settings. 11. Select the DNS server interface from the available WAN interfaces. 12. Click the arrows to move your selection from left to right or from right to left. 13. Alternatively, you can enter static DNS IP addresses in the Use the following Static DNS IP address section. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
14. Click Next. The summary page appears indicating that your PPPoE WAN setup is complete. 15. Review the summary and either click Apply/Save to commit your changes or click Back to step through the pages in reverse order to make any necessary alterations. IP over Ethernet There are several parts to configuring a IP over Ethernet WAN service. You will progress through several pages to complete the configuration. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. Select the Layer2 interface to use for the WAN service and click Next. The following page appears. 3. Select the IP over Ethernet WAN service type. 4. Modify the other fields as needed. The fields on this page are explained in the following table. Field Name Description Enter Service Description (Optional) Enter a name to describe this configuration. Enter 802.1P Priority Enter a priority for this WAN service. Options are 0 - 7. The default is 0.
Field Name Description For untagged service, enter -1 (disabled) in this field and the 802.1P Priority field. Select VLAN TPID Select the TPID for this VLAN. Options are 0x8100, 0x88A8, and 0x9100. Internet Protocol Selection This data packet scheduling technique allows different scheduling priorities to be applied to statistically multiplexed data flows.
6. Enter the relevant WAN IP Settings. The fields on this page are explained in the following table. Field Name Description Obtain an IP address automatically When you wish the ISP to automatically assign the WAN IP to the gateway. Option 60 Vendor ID (Optional) Broadcast a specific vendor ID for the DHCP server to accept the device. Option 61 IAID (Optional) Interface Association Identifier (IAID). A unique identifier for an IA, chosen by the client.
Field Name Description not specify a prefix length, the default of /64 is used. Specify the Next-Hop IPv6 address In the WAN Next Hop IPv6 Address field, enter the IP address of the next WAN in the group. This address can be either a local link or a global unicast IPv6 address. 7. Click Next. The following page appears. 8. Modify the settings if desired. All settings are optional.
Field Name Descriptopn Enable NAT This option is enabled by default and supports sharing the WAN interface across multiple devices on the LAN. Also enables the functions in the NAT sub-menu and addition PPPoE NAT features to select. Click the checkbox to disable NAT. Enable Fullcone NAT Enables one-to-one NAT. Enable Firewall This option is enabled by default and enables functions in the Security sub-menu. Enable SIP ALG Click to enable Session Initiation Protocol (SIP) pass-through NAT.
1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. Select an ATM interface for the WAN service and then click Next. The following page appears. 3. Select Bridging. The multicast source fields appear. 4. Modify the fields as needed, using the information in the following table. Field Name Description Allow as IGMP Multicast Source Select to enable this service to act as an IGMP multicast source. Allow as MLD Multicast Source Select to enable this service to act as an MLD multicast source.
Field Name Description For tagged service, enter values in this field and the 802.1P Priority field. For untagged service, enter -1 (disabled) in this field and in the 802.1P Priority field. Select VLAN TPID (Optional) Select the TPID for this VLAN. Options are 0x8100, 0x88A8, and 0x9100. 5. Click Next. The summary page appears indicating that your Bridging WAN setup is complete. 6.
LAN On the Local Area Network (LAN) Setup page, you can configure the router’s local IP addresses, subnet mask, DHCP behavior and other related LAN side settings for your gateway. 1. In the left navigation bar, click Advanced Setup > LAN. The following page appears. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. Customize the fields as desired. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description GroupName Select an interface group from the list of available groups (defined on the Interface Grouping page). IP Address Enter the LAN IP address to be used by LAN devices connecting to this gateway. Subnet Mask Enter the subnet mask to be used by LAN devices connecting to this gateway.
Field Name Description l l Option 150: Enter a comma-separated list of TFTP IPv4 server addresses. The maximum allowed is 2. Option 43: Enter the loopback address of the master controller in ASCII format. Configure the second When you select this option, the IP Address and Subnet Mask fields appear where IP address and subyou can enter a second IP address and Subnet mask to support a second, simnet mask for LAN ultaneous LAN. interface For example, the primary LAN might be defined as 192.168.0.
1. In the left navigation bar, click Advanced Setup > LAN > IPv6 Autoconfig . The following page appears. 2. Modify the fields as needed, using the information in the table below. 3. Click Save/Apply to commit your changes. The fields on this page are explained in the following table. Field Name Description Interface Address IPV6 address to assign as the gateways Local LAN IPV6 address and prefix length. Prefix length is required.
Field Name Description options. Zero compression is not supported. Make sure to enter zeros between the colons, that is, do not use shorthand notation (::2). Options are: l Start interface ID: Enter the beginning IPv6 available addresses for DHCP to assign to LAN devices. Enable RADVD l End interface ID: Enter the ending IPv6 available addresses for DHCP to assign to LAN devices. l Leased Time (hour): Amount of time before a new IPv6 lease is requested by the LAN client.
1. In the left navigation bar, click Advanced Setup > Ethernet Config . The following page appears. 2. In the Configure column, select an option (Auto, 100 Full, 100 Half, 10 Full or 10 Half) for each of the four Ethernet ports on your gateway. These options represent 100 megabits or 10 megabits using half or full duplex transmission protocols. When you have a specific device with a known limited transmission speed capability, select one of the latter four options.
NAT In this section, you can configure the settings for Network Address Translation including setting up virtual servers, port triggering and a DMZ host. There is seldom need to customize these settings as the default settings manage the related features sufficiently for most environments. Virtual Servers Virtual Servers (more commonly known as Port Forwards) is a technique used to facilitate communications by external hosts with services provided within a private local area network.
1. In the left navigation bar, select Advanced Setup > NAT and then click Add. The following page appears. 2. Customize the fields to create your port forwarding entry. 3. Click Apply/Save to commit your changes. The servers for the selected service appear on the NAT Virtual Servers Setup page. The fields on this page are explained in the following table. Field Name Description Use Interface Select the WAN interface to which this NAT rule will apply.
Field Name Description Server IP Address Enter the IP address of the LAN client where the service is hosted. External Port Start Enter the first external port for this server. External Port End Enter the last external port for this server. Protocol Select the protocol to be used with this range of ports. Options are: TCP, UDP, or TCP/UDP. Internal Port Start Enter the first internal port for this server. Internal Port End Enter the last internal port for this server.
Field Name Description Use Interface Select the interface for which the port triggering rule will apply. Select an Application Select the application which requires a port trigger entry. The Port and Protocol fields are populated. Custom Application If the application you want does not appear in the selection list, enter a unique name for the application for which you are creating a port trigger entry. Trigger Port Start Enter the starting number of the range of available outgoing trigger ports.
Security In this section, you can configure filtering for IP and MAC. IP Filtering - Outgoing On this page, you can add an outgoing filter when refusal of data from the LAN to the WAN is desired. 1. In the left navigation bar, click Advanced Setup > Security and then click Add. The following page appears. 2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit the completed entry. The fields on this page are explained in the following table.
Field Name Description Source IP address [/prefix length] Enter the source IP address of a LAN side host for which you wish to filter/block outgoing traffic for the specified protocol(s). Note: The address specified here can be a particular address or a block of IP addresses on a given network subnet. This is done by appending the associated routing "/prefix" length decimal value (preceded with the slash) to the addresses.
2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Filter Name A free-form text field. Enter a descriptive name for this filter. IP Version Select the IP version for this filter. Options are IPv4 and IPv6. The default is IPv4. Protocol Select the protocol to be associated with this incoming filter. Options are: TCP/UDP, TCP, UDP, or ICMP.
MAC Filtering Your SmartRG gateway can block or forward packets based on the originating device. This MAC filtering feature is available only in Bridge mode. For other modes, similar functionality is available via IP Filtering. On this page, you can manage MAC filtering for your gateway. 1. In the left navigation bar, click Advanced Setup > Security > MAC Filtering. The following page appears. 2. To modify policy settings: a. Review the information on the page. b.
Add a MAC Filtering Rule You cannot edit rules but you can add new ones and then remove the obsolete ones. 1. On the MAC Filtering page, click Add. The following page appears. 2. Fill in the fields, using the information provided in the following table. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Protocol Type Select the protocol associated with the device at the destination MAC address.
Time Restriction On this page, you can restrict Internet access to particular days and specific times for each device that accesses your gateway. 1. In the left navigation bar, click Advanced Setup > Parental Control > Time Restriction and then click Add. The following page appears. 2. Fill in the fields using the information in the table below. 3. Click Apply/Save. The fields on this page are explained in the following table.
URL Filter On this page, you can exclude and include URLs as desired to control access to them. Each list can include up to 100 addresses. Note: Only one Exclude list and one Include list are supported for each gateway. Unique lists are not supported for connecting devices. 1. In the left navigation bar, click Advanced Setup > Parental Control > Url Filter. 2. To block a URL: a. Select Exclude List. b. Click Add. The following page appears. c. Click Apply/Save to save your settings.
QoS Config On this page, you can enable QoS and set the DSCP Mark classification. The maximum number of queues that can be configured vary by mode, as shown below. Mode Maximum # of queues ATM 16 Ethernet 4 per interface PTM 8 Note: Wireless queues (e.g., the WMM Voice Priority queue) are shown only when wireless is enabled. If the WMM Advertise function on the Wireless Basic Setup page is disabled, assigning classifications to wireless traffic has no effect. 1.
Supported DSCP Values The DSCP marking QoS Queue Management Configuration marking on ingress packets is based on the selection you make in the Select Default DSCP Mark field. The selected default marking is applied automatically to all incoming packets without reference to a particular classification. Note: A default DSCP mark value of Default(000000) will mark all egress packets that do NOT match any classification. The following values are supported.
3. In the Interface field, select the Layer 2 interface to be associated with this queue. Options include Dynamic WAN and the interfaces defined for your gateway. When you select an interface, additional fields appear. If you select Dynamic WAN, they appear once for each defined WAN interface. 4. Fill in the other fields, using the information in the table below. 5. Click Apply/Save to save your settings. The fields on this page are explained in the following table.
WLAN Queue On this page, you can view the wireless queues and classifications. Note: The WMM Advertise option must be enabled before these classifications will function. This option is enabled by default. If you have disabled it, go to the Wireless > Basic page and clear the Disable WMM Advertise checkbox. In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Queue Config > Wlan Queue. The following page appears.
1. In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Classification and then click Add. The following page appears. A maximum of 32 entries can be configured. 2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Traffic Class Name Enter a descriptive name for this rule. This is a free-form text field.
Field Name Description Rule Status Select whether this rule is active or inactive. Options are: Enable and Disable. The default is Enable. Specify Classification Criteria section Ingress Interface Select an interface. Options are LAN, WAN and any interface already configured for your gateway. Ether Type Select the Ethernet interface type for this classification. Options include: IP, ARP, IPV6, 8855, 8856,and 8021Q . Source MAC Address Enter the source MAC address and mask for this classification.
QoS Port Shaping QoS Port Shaping facilitates setting a fixed rate (Kbps) for each of the Ethernet ports. 1. In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Port Shaping. The following page appears. 2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table.
Routing In this section, you can configure default gateways, static routing, policy routing and RIP settings. Default Gateway On this page, you can configure the default gateway interface list to establish access priority, that is, iInterfaces are accessed in the order listed in the Selected Default Gateway Interfaces column. 1. In the left navigation bar, select Advanced Setup > Routing. The following page appears. 2. Select the interfaces that you want used as default gateway interfaces.
1. In the left navigation bar, click Advanced Setup > Routing > Static Route and then click Add. The following page appears. 2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description IP Version Select the IP version associated with the static route you wish to create. Options are: IPv4 and IPv6.
1. In the left navigation bar, click Advanced Setup > Routing > Policy Routing and then click Add. The following page appears. 2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Policy Name Enter a descriptive name for this entry to the policy routing table. This is a free-form text field. Physical LAN Port Select a physical LAN interface for the policy route.
1. In the left navigation bar, click Advanced Setup > Routing > RIP, and then click Add. The following page appears. 2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Interface Available WAN interfaces. Version Select the applicable Routing Interface Protocol version. Options are: 1, 2, and Both. The default is 2. Operation Select the operation mode.
DNS In this section, you can configure a DNS server, dynamic DNS and static DNS. DNS Server On this page, you can input the Domain Name Server (DNS) information supplied by your service provider. 1. In the left navigation bar, click Advanced Setup > DNS. The following page appears. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. Modify the settings as needed, using the information supplied by your provider and that supplied in the table below. 3. Click Apply/Save. The fields on this page are explained in the following table. Field Name Description Select DNS Server Interface Select entries in the Selected DNS Server Interfaces and Available WAN Interfaces columns and click the arrows to move them left or right. At from available WAN interfaces least one entry must remain in the Selected DNS Server Interfaces column.
The fields on this page are explained in the following table. Field Name Description D-DNS provider Select a dynamic Domain Name Server provider. Hostname Enter the hostname of the dynamic DNS server. Interface Select the gateway WAN interface whose traffic will be pointed at the specified Dynamic DNS provider. Username Enter the username for the dynamic DNS server. Password Enter the password for the dynamic DNS server.
DSL On this page, you can configure settings for the DSL interface. Caution: Altering these settings unnecessarily can result in the gateway being unable to attain DSL synchronization. 1. In the left navigation bar, click Advanced Setup > DSL. The following page appears. 2. Modify the fields as needed. 3. Click Apply/Save to commit your changes. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
The fields on this page are explained in the following table. Modulation Data Transmission Rate Max Downstream Max (Mbps) Upstream (Mbps) G.Dmt ITU-T G.992.1 standard. 12 1.3 G.lite ITU-T G.991.2 standard. 4 0.5 T1.413 ANSI T1.413 Issue 2 standard. 8 1.0 ADSL2 ITU-T G.992.3 standard. 12 1.0 AnnexL Annex L of ITU-T G.992.3 standard which supports longer loops but with reduced transmission rates. ADSL2+ ITU-T G.992.5 standard. 28 1.0 AnnexM Annex L of ITU-T G.992.
UPnP On this page, you can enable UPnP when 3rd party devices on your LAN support this Universal Plug and Play standard. Common client devices include gaming consoles, IP cameras, printers and others. This feature is enabled by default. 1. In the left navigation bar, select Advanced Setup > UPnP. The following page appears. 2. To disable this option, click Enable UPnP to clear the box. 3. Click Apply/Save to commit your changes. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
DNS Proxy On this page, you can configure the DNS proxy settings. A DNS proxy improves domain look-up performance for clients by creating a historical cache of look-ups. 1. In the left navigation bar, click Advanced Setup > DNS Proxy. The following page appears. This feature is enabled by default. 2. To disable the DNS proxy feature, click the Enable DNS Proxy checkbox to clear it. The Host name and Domain Name fields are hidden. 3. Click Apply/Save to commit your changes. SMARTRG INC.
Interface Grouping On this page, you can create an interface group to map local interfaces to WAN interfaces. A typical application for this feature is assigning IPTV set-top boxes to a WAN interface. 1. In the left navigation bar, click Advanced Setup > Interface Grouping and then click Add (below the table). The following page appears. (The instructions that display at the top of this page are not shown below). SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. To create a new interface group, enter a unique Group Name, then proceed with either step 3 (dynamic) or step 4 (static) below. 3. If this new grouped interface is to share the WAN interface, click Shared WAN Interface. Not selecting this option this will cause the WAN interface you select to be removed from any other interface groups.
4. In the Available WAN Interfaces list, select the interface(s) that you want to group and click the left arrow to move it to the Grouped WAN Interfaces list. Hold down the CTRL key or Shift key to select multiple interfaces. Note: Depending on the WAN interface configuration, these clients may obtain public IP addresses. 5. Do the same in the Grouped and Available LAN Interfaces lists for any applicable LAN interfaces. 6.
3. Select the WAN and LAN interfaces associated with the tunnel you wish to establish. The Manual button is selected by default. 4. Enter the appropriate values in the IPv4 Mask Length, 6rd Prefix with Prefix Length and Border Relay IPv4 Address fields. 5. Click Apply/Save to commit your changes. IPv4inIPv6 On this page, you can configure the IPv4inIP6 settings. 1. In the left navigation bar, click Advanced Setup > IP Tunnel > IPv6inIPv4 and then click Add. The following page appears. 2. 3. 4. 5.
IPSec Internet Protocol Security is a protocol for securing communications by packet level encryption and authentication. On this page, you can enable and remove connections, or edit existing connections. 1. In the left navigation bar, click Advanced Setup > IP Sec and then click Add New Connection. The following page appears. 2. Enter your connection details by completing the appropriate fields. 3. If desired, click Advanced IKE Settings to select Phase 1 and Phase 2 specific parameters.
Field Name Description IPSec Connection Name A free form text field. Enter a descriptive name for this connection IP Version Select the IP version environment associated with your infrastructure. Options are IPv4 and IPv6. Tunnel Mode Select the encapsulation method to be used. Options are: l ESP: Use this mode to encapsulate a packet with ESP and IP headers. An ESP trailer is added to the packet for authentication and integrity. l AH: Use this mode to encapsulate a packet with AH and IP headers.
1. On the IPSec Settings page, click Show Advanced IKE Settings to display the Phase 1 and Phase 2 fields. 2. Fill in the fields, using the information in the table below. Field Name Description Mode Select a mode. Options are Main and Aggressive. Encryption Algorithm Select the encryption algorithm. Options are 3DES , AES 128, AES-192, and AES-256. Integrity Algorithm Select the integrity algorithm. Options are MD5 and SHA1. Select Diffie-Hellman Group for Key Exchange Select the D-H group.
1. In the left navigation bar, click Advanced Setup > Certificate > Local and then click Create Certificate Request. The following page appears. 2. Enter your connection details by completing the appropriate fields. For more information about certificates, refer to the ITU X.509 standard. 3. Click Apply to complete the request. The fields on this page are explained in the following table. Field Name Description Certificate Name A free-form text field used to describe the intended use of the certificate.
4. To import a certificate and the corresponding private key, click Import Certificate. The following page appears. 5. 6. 7. 8. In the Certificate Name field, type "cpecert". Paste the Certificate details between the BEGIN and END markers. Paste the Private Key information between the BEGIN and END markers. Click Apply to implement this certificate. Trusted CA On this page, you import and store up to four trusted certificates.
1. In the left navigation bar, click Advanced Setup > Certificate > Trusted CA and then click Import Certificate. The following page appears. 2. In the Certificate Name field, type "acscert", and then paste the certificate details between the BEGIN and END markers. 3. Click Apply to commit this certificate. After you add one certificate, a Remove button appears on the Trusted CA landing page. Click this button to remove the current certificate and replace it with a new one. SMARTRG INC.
Multicast Multicast methodology is used for applications shipping information simultaneously to multiple destinations. The most common scenario is Internet television and other streaming media. In IP Multicast, the implementation occurs at the IP routing level, where routers create the most efficient distribution paths for packets sent to a destination. On this page, you can configure the multicast settings. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
1. In the left navigation bar, select Advanced Setup > Multicast. The following page appears. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. In the Multicast Precedence field, select whether IGMP packets are given priority handling and at what level. Options are: l l Disable: IGMP packets are not prioritized. This is the default. Enable: IGMP packets are prioritized using the multicast precedence value. The lower the multicast precedence value, the higher that IGMP packets will be placed in the queue. 3. In the Multicast Strict Grouping Enforcement field, select whether grouping is stricly enforced. Options are Disable and Enable.
Field Name Description l l Enabled: Group members are removed immediately. Disabled: Group members are removed after a query is sent and a response received. LTE WAN Service In this section, you can view LTE WAN status and configure the related network settings. Status Information On this page, you can view information about the LTE connection between your provider and your gateway. In the left menu, click LTE WAN Service > Status Information. The following page appears.
Field Name Description Model Model of the LTE Module. Firmware Version Firmware version of the LTE Module IMEI International Mobile Equipment Identity is a unique 15-digit number used to identify valid equipment on a network provider. IMSI International Mobile Subscriber Identity is a unique number stored on the SIM Card used to identify the subscriber of the network provider. LTE Information section Network Connected Status State of the LTE connection.
Field Name Description Network Mode section Network Select the Network Dial Mode. Options are 4G/3G Auto, 4G Only, and 3G Only. Dial Mode APN Settings section APN Name Enter the Access Point Name for your network provider. Wireless In this section, you can configure the wireless interface settings for your gateway, including basic and advanced settings, MAC filtering, and wireless bridging. Note: While separate pages are provided for both wireless bands (2.
2. Modify the settings as desired, using the information provided in the table below. The table at the bottom of the page lists the guest/virtual access points defined for your gateway. If desired, you can define up to three virtual access points for guest use. 3. Click Apply/Save to commit your settings. The fields on this page are explained in the following table. Field Name Description Enable WiFi Button This option is enabled by default.
Field Name Description Clients Isolation Click to prevent LAN client devices from communicating with one another on the wireless network. Disable WMM Advertise Click to stop the wireless from advertising Wireless Multimedia (WMM) functionality. WMM provides basic Quality of Service (QOS) for applications. Enable Wireless Multicast Click to enable Wireless Multicast Forwarding (WMF). Multicast traffic is forForwarding warded across wireless clients. SSID Enter the Wi-Fi SSID.
2. Modify the settings as needed, using the information provided in the field description table. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Enable WPS Select to enable Wi-Fi Protected Setup. Options are: Enabled and Disabled. Add Client (Appears when WPS is enabled) Select the method for generating the WPS PIN. Options are: Enter STA PIN and Use AP PIN. To add an enrollee station, click Add Enrollee.
Field Name Description mode is automatically made active. Set WPS AP Mode (Appears when WPS is enabled) Select how security is assigned to clients. l Configured: The gateway assigns security settings to clients. l Device PIN Unconfigured: An external client assigns security settings to the gateway. (Appears when WPS is enabled) The PIN for the gateway. This value is generated by the access point.
3. Fill in the fields, using the information in the field description table below. 4. Click Apply/Save to save the settings. The fields on this page are explained in the following table. Field Name Description Select SSID Select the SSID of the wireless network to which this security configuration will apply. WEP Encryption Select to enable Wired Equivalent Privacy (WEP) mode. Options are Enabled and Disabled.
2. Fill in the fields, using the information in the field description table below. 3. Click Apply/Save to save the settings. The fields on this page are explained in the following table. Field Name Description RADIUS Server IP Enter the IP address of the RADIUS (Remote Authentication Dial In User Service) server assoaddress ciated with your network. RADIUS Port Enter the port number for the RADIUS server. Port 1812 is the current standard for RADIUS authentication per the IETF RFC 2865.
WPA2 & Mixed WPA2/WPA Authentication The same configuration fields apply for both WPA2 and Mixed WPA2/WPA authentication methods. 1. On the Wireless > Security page for the band that you want to configure, select WPA2 or Mixed WPA2/WPA in the Network Authentication field. The following fields appear. 2. Fill in the fields, using the information in the field description table below. 3. Click Apply/Save to save the settings. The fields on this page are explained in the following table.
Field Name Description address associated with your network. RADIUS Port Enter the port number for the RADIUS server. Port 1812 is the current standard for RADIUS authentication per the IETF RFC 2865. Older servers may use port 1645. Options are 1 - 65535. RADIUS Key (Optional) Enter the encryption key (if required) needed to authenticate to the specified RADIUS Server. WPA Encryption Select the encryption standard.
Field Name Description Select SSID Select the SSID of the wireless network to which this security configuration will apply. Protected Management Frames Select whether to enable this option. Options are Disabled, Capable, and Required. The default is Disabled. WPA passphrase Enter the security password to be used by this security configuration. WPA Group Rekey Inter- The frequency at which the gateway automatically updates the group key and val sends it to connected LAN client devices.
l Disabled: MAC filtering is off. l Allow: Access for the specified MAC address is permitted. You must add at least one MAC address. l Deny: Access for the specified MAC address is rejected. 4. To add a MAC address to the filter list: a. Click Add. b. Enter the MAC address. c. Click Apply/Save. You are returned to the main MAC filtering page. 5. To remove a MAC address from the list, click the Remove checkbox next to it and then click the Remove button below the list. 6.
Field Name Description AP Mode Select whether to enable or disable access point (AP) functionality. Options are: l Wireless Bridge: Disables AP functionality. l Bridge Restrict (Optional) Select to enable or disable wireless bridge restriction. Options are: l Enabled or Enabled(Scan): Enables wireless bridge restriction. This is the default. Only bridges specified in the Remote Bridge MAC Address field are granted access. Click Refresh to update the station list. The list takes a few seconds to update.
1. In the left navigation bar, click Wireless > Advanced. The following page appears. 2. Modify the fields as needed, using the information in the field description table. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
Field Name Description Band The wireless band that you are configuring. This field is set to 5GHz in the Wireless > 5 GHz Band submenu and to 2.4GHz in the Wireless > 2.4 GHz Band submenu. Channel Select the Wi-Fi channel you want to use. Options include Auto and 36/80 - 161/80 for the 5 GHz band and are Auto and 1 - 7 for the 2.4 GHz band. It is recommended to use only non-overlapping channels, e.g., 1, 5 and 7.
Field Name Description l RX Power Chain Save Enable: The gateway automatically reverts to 20 MHz channel bandwidth when another WiFi network within 2 channels of its own channel is detected or when a client device with its 40 MHz Intolerant bit set is detected. Select whether to turn on power-save mode. Options are Disable and Enable. The default is Enable. Note: Before setting this parameter, set 802.11n/EWC to Auto.
Field Name Description Check work. The displayed value is -1. TPC Mitigation(db) Select the TPC mitigation value in db. Options are 0(off), 2, 3, and 4. The default is 0 (off). Transmit Power Select the desired output power (by percentage). Options are 20%, 40%, 60%, 80%, and 100%. The default is 100%. WMM (Wi-Fi Multimedia) Select whether to enable this technology. It allows multimedia services (audio, video and voice packets) to get higher priority for transmission.
Wifi Insight On this page, you can configure the WiFi Insight system. 1. In the left navigation menu, click Wireless > Wifi Insight. The following page appears. You can also reach this page by clicking Wireless > Wifi Insight > Configure. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
2. In the Sample Interval section, select the number of seconds for sampling to occur. Options are 5, 10, 15, and 20 seconds. The default is 5 seconds. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
3. In the Start/Stop Data Collection section, configure the data sample: a. Click Start collecting data every. The days-of-the-week checkboxes become active. b. Select the days of the week when the data should be collected. c. In the From and To fields, click in the fields and use the plus (+) and minus (-) icons to change the start and end times for collection. You can close the selection box by clicking the X on the box or clicking in the field again. 4. In the Database Size section: a.
1. In the left navigation menu, click Wireless > Wifi Insight > Site Survey. The following page appears. 2. 3. 4. 5. In the first field above the chart, select the wireless network that you want to review. In the Select Channel field, select the channel that you want to review. In the Select Bandwidth field, select the bandwidth. Click Scan. The page refreshes to show the requested information.
1. In the left navigation menu, click Wireless > Wifi Insight > Channel Statistics. The following page appears. 2. In the field at the top of the page, select the wireless band to review. Information is shown for associated stations, channel capacity, interference levels, adjacent channels, and channel distribution. Metrics On this page, you can view glitch counter, chanim, associated stations, and packet queue statistics for your wireless networks. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL.
1. In the left navigation menu, click Wireless > Wifi Insight > Metrics. The following page appears. 2. In the field at the top of the page, select the wireless band to review. Information is shown for glitch counters, chanim, associated stations, and packet queues. Diagnostics in this section, you can run line performance tests. Three legs of the data path are included in the available tests: LAN connectivity, DSL connectivity and Internet connectivity tests.
1. In the left navigation bar, click Diagnostics > Diagnostics. The following page appears. 2. To refresh the data, click Test at the bottom of the page. The normal test method is initiated, utilizing OAM F5 loopback cells. The table is updated with fresh diagnostic information about connection integrity. To learn more about what is being tested and what actions to take when a test fails, click the Help link at the far right of each line item. 3.
1. In the left navigation bar, click Diagnostics > Ethernet OAM. The following page appears. 2. Modify the fields as needed, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. Field Name Description Ethernet Link OAM (802.3ah) section Ethernet Link OAM (802.3ah) Click the Enabled checkbox to set options for this protocol. The fields described below appear.
Field Name Description Local MEP ID Enter the ID of the local MEP. Options are 1 - 8191. Local MEP VLAN ID Enter the ID of the VLAN for the local MEP. Options are 1 - 4094. The default is -1 (no VLAN tag). CCM Transmission Select to enable CCM transmission. Remote MEP ID Enter the ID of the remote MEP. Options are 1 - 8191. The default is -1 (no remote MEP). Loopback and Linktrace Test section Target MAC Enter the MAC address for the test, e.g., 02:10:18:aa:bb:cc.
Trace Route to Host On this page, you can use the Trace Route utility to trace a connection. 1. In the left navigation menu, click Diagnostics Tools > Trace Route to Host. The following page appears. 2. Enter the host name or IP address that you want to trace. 3. Click Trace Route to Host). The details of the trace appear on the page. Management In this section, you can manage configuration files, access control, management server configurations, SNMP Agent settings, and work with event logs.
1. In the left navigation bar, click Management > Settings. The following page appears. 2. To save a backup file of the currently running settings to a local drive, click Backup Running Settings. The open/save dialog box appears. Click OK. The backupsettings.conf file is created in your default download location. 3. To save a backup file of the default settings to a local drive, click Backup Default Settings. The open/save dialog box appears. Click OK. The backupdefaultsettings.
Update On this page, you can restore previously backed-up gateway settings. Both Current and Default settings can be managed here. 1. In the left navigation bar, click Management > Settings > Update. The following page appears. 2. Click the Browse button for the type of setting you wish to restore. 3. Locate the desired configuration file on your local system and click Open. 4. Click the appropriate Update button. The gateway reboots when the update has completed. SMARTRG INC.
Restore Default On this page, you can reset the gateway to its default settings which can be the factory defaults or defaults that you customized and stored. For details, see the "Restore Default" and "Restore Default" sections . 1. In the left navigation bar, click Management > Settings > Restore Default. The following page appears. 2. Click Restore Default Settings. The gateway is rebooted. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
System Log On this page, you can view and configure the system log generated for your gateway. 1. In the left navigation bar, click Management > System Log. The following page appears. 2. To view the contents of the system log, click View System Log. The System Log details page appears. 3. To update the displayed entries, click Refresh. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
4. To modify the system log settings: a. Click Configure System Log. The System Log - Configuration page appears. b. Modify the settings as needed. The following table describes the options for configuration of the system log. Action Description Log Select to turn logging off or on. The default is Disable. Logging Level Select Error unless actively troubleshooting a situation with a subscriber for which increased log detail is required.
c. Click Apply/Save to save your changes. Security Log The security log contains a history of events related to sensitive access to the gateway. Logged events include: l Password change success/failure l Authorized login success/failure l Authorized user logged out l Security lockout added/removed l Authorized/Unauthorized resource access l Software update 1. In the left navigation bar, click Management > Security Log. The following page appears. 2.
SNMP Agent On this page, you can configure the SNMP (Simple Network Management Protocol) settings to retrieve statistics from the SNMP agent for the gateway. You can enable or disable the SNMP agent and set parameters such as the read community, system name and trap manager IP. 1. In the left navigation bar, click Management > SNMP Agent. The following page appears. 2. To enable SNMP, click Enable in the SNMP Agent field. 3. Modify the other fields as needed, using the information in the following table.
Management Server A management server is an Auto Configuration Server (ACS) such as Cisco Prime Home which offers significant advantages in terms of automation and productivity when managing subscriber devices in the field. In this section, you can configure ACS settings for the TR-069 client and configure STUN server settings. TR-069 Client On this page, you can configure the gateway with details about the management ACS to which this gateway will be linked.
1. In the left navigation bar, click Management > Management Server > TR-069 Management. The following page appears. 2. Update or complete the necessary fields per the instructions from your ACS platform vendor. 3. Click Apply/Save to commit your changes. Note: This manual does not cover the setup of your ACS. Consult the materials provided by your ACS vendor to determine the appropriate parameters and server settings for configuring remote WAN side management via an ACS using the TR-069 Protocol.
Field Name Description ware versions prior to 2.5.0.2, MAC is the only available option. l TR-069 Client Serial Number: This option is available for SmartRG gateways using firmware versions later than 2.5.0.2. Enable or disable the TR-069 client on the CPE. You can disable the TR-069 WAN Management Client if no ACS is employed. Note: If you may want to add an ACS to your infrastructure in the future, it is recommended that you leave this option enabled.
Field Name Description Connection Request URL This option is set to (null) by default and cannot be changed. 5. To force the gateway to attempt to sync with the ACS, click the GetRPCMethods button. This will assist you in verifying the TR-069 parameters entered above. STUN Config STUN stands for “Simple Traversal of UDP through NATs”. STUN enables a device to find out its public IP address and the type of NAT service it is sitting behind.
2. To view the required STUN settings, click STUN Server Support. Additional fields appear. 3. Complete each field in accordance with the implementation specifics of your server. 4. Click Save/Apply to commit your changes. The fields on this page are explained in the following table. Field Name Description STUN Server Address The physical STUN server’s assigned network address. An invalid address will produce an immediate on-page error message from the gateway. You can enter a maximum of 256 characters.
* This mechanism is used in coordination with the refreshing of NAT bindings. Specifically, in conjunction with use of Restricted Cone NAT or Port Restricted Cone NAT (as may be configured in some gateways). A device’s internal address / port mappings, which the STUN protocol is allowed to make use of, can have keep alive values attributed.
2. Click Automatically synchronize with Internet time server. A list of server fields and the Time Zone offset field appear. 3. Select servers from the list or enter your own NTP servers. 4. Select the desired time zone for the gateway. 5. Click Apply/Save to commit your settings. Access Control In this section, you can manage access to your gateway and network. You can configure passwords, accounts, services, access lists, and the logout timer. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL.
Accounts On this page, you can create and manage user accounts for your gateway. Your gateway can support multiple login accounts for its on-board user interface. Each account can be customized to grant access privileges to specific pages in the interface. This is particularly useful when an ISP wishes to limit access for subscribers, yet grant full access for technical support and on-site installation personnel. Add an Account 1. In the left navigation bar, click Management > Access Control > Accounts.
2. To set up a new user, click Create Account. The following page appears. 3. Enter a Username and Password for the new account. 4. Select the features that you want this user to access. If you select a subcategory, the subordinate boxes are also selected. 5. Click Save Account to commit your changes. The new account is created. To test the account credentials, log out of the interface and then log back in using the new account.
You must be logged into the gateway as the Admin or Support user to modify or delete any accounts. 1. In the left navigation bar, click Management > Access Control > Accounts and then click, Delete/Modify Account. The Delete/Edit Account page appears. 2. In the Select an account field, select the account you wish to modify or delete. SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
3. Do one of the following: a. To modify an account, check or clear the desired boxes and then click Update Account to commit your changes. b. To delete an account, scroll to the bottom of the page and click Delete Account to remove the account. c. To disable or enable an account, click the Enable/Disable account buttons. Your changes are implemented immediately.
The fields on this page are explained in the following table. Field Name Description Services This column identifies the SCL services that can be enabled or disabled. Options are: FTP, HTTP, ICMP, SNMP, SSH, TELNET, and TFTP. Use encrypted HTTP(S) Click this checkbox to implement secured HTTP. This option is enabled for the LAN. Warning: When you click this option, the gateway reboots. LAN Select the service enabled on LAN side firewall.
1. In the left navigation bar, click Management > Access Control > Passwords. The following page appears. 2. Enter the information for the logged-in account. 3. Click Apply/Save to commit your settings. The fields on this page are explained in the following table. Field Name Description User Name Specifies name of account to be configured. Options are admin, support, user. Old Password Enter the current password for the entered User Name.
2. To add an address: a. Click Add. The following page appears. b. Enter the address for which you want to restrict access. c. Click Apply/Save. You are returned to the Management Access Lists page. d. To add up to 9 more addresses, repeat steps 2a - 2c. 3. To remove an address, click the Remove checkbox next to it and then click Remove. The list is updated. Logout Timer On this page, you can define the maximum time that a session can remain open before the gateway logs out. 1.
Update Software On this page, you can update the firmware of your SmartRG gateway. Software updates for SmartRG products are available for download by direct customers of SmartRG via the SmartRG Customer Portal. 1. In the left navigation bar, click Management > Update Software. The following page appears. 2. Follow the on-page instructions. When the update has completed, the gateway reboots. Reboot Occasionally, troubleshooting measures may require that the gateway be rebooted.
Logging Out 1. To log out of your gateway, click Logout in the left navigation menu. The Broadband Router Logout page appears. 2. Click the Logout button. A success message appears. Appendix: Compliance Statements FCC Interference Statement This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: l This device may not cause harmful interference.
FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. l This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. l This equipment should be installed an operated with a minimum distance of 20cm between the radiator and your body.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this device does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. IC CS-03 statement This product meets the applicable Industry Canada technical specifications.
5GHz 5150-5350 MHz band is restricted to indoor operations only. Revision History REV DATE CHANGES 1.0 Initial release. March 2017 SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED.
