Quick Start Guide SR570ac This Quick Start Guide shows you how to set up and start using your new gateway.
INSTALLATION Locate the splitter cable that is included with your SmartRG gateway. It has three ports. 1. Connect one end of an Ethernet cable to the wall jack installed by your service provider. Connect the other end to the WAN port on the gateway. 2. Connect one end of an Ethernet cable to a LAN port on the gateway. Connect the other end to the Ethernet port on your PC. 3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the gateway. 4.
LED INDICATORS The LEDs on the front of the SR70n gateway can help you understand the current state of your adapter.
QUICK GATEWAY CONFIGURATION Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the hole, press the Reset button gently for 1 second, and then release the button. The system reboots and returns to the factory defaults.
2. Enter the default credentials shown below and click OK. User Name: admin Password: admin Note: Your service provider may use other settings. Contact your provider for details. 3. At the bottom of the page, click Manage gateway (advanced). The gateway interface appears, showing the Device Info summary page.
WiFi Setup Two methods, WPS and Manual, are available for configuring your wireless connection. Perform the steps on this page first, and then follow the instructions for the applicable method. 1. In the left menu, click Wireless. The Wireless Basic page appears. 2. If desired, in the SSID field, enter the network name to which you want your client devices connected. 3. Continue with the steps for the method you prefer.
WPS Method If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method, follow these steps. 1. In the left menu, click Wireless. Click the wireless band that you want to configure and then click Security. 2. In the Enable WPS field, verify that Enabled is selected. . 3. Click Apply/Save to commit your selection. 4. Within 2 minutes, activate WPS on the 3r- party device to which you wish to connect.
Manual Method You can manually configure a wireless connection. Once your gateway’s other parameters are set up, follow these steps. 1. In the left menu, click Wireless. Click the wireless band that you want to configure and then click Security. 2. Scroll down to the Manual Setup AP section. 3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You will need this ID for Step 8. 4. Select the desired Network Authentication method.
OPTIONAL WALL MOUNT Using a Phillips-head screwdriver, remove the mount from the bottom of the gateway. Using the template below, attach the two screws to the wall. Using wall anchors is recommended. 1/16” (2-3mm) Wall Anchor 4 1/8” (104mm) Slide the back of the gateway down on the screws. Note: If a bracket is included with your gateway, slide the bracket into the holes on the back of the gateway and then slide the bracket down on the screws.
Record your SR570ac WiFi Settings Predefined wireless settings If you change the preset wireless settings WiFi network name (SSID) Network key (password) Additional Support If you require further instructions, please contact your local ISP Support. SMARTRG INC. ALL RIGHTS RESERVED.
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3.
2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans fil) pendant un orage électrique. Ceci peut présenter un risque de choc électrique causé par la foudre. 3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite. 4. ATTENTION - Pour réduire les risques d’incendie, utiliser uniquement des conducteurs de télécommunications 26 AWG au de section supérleure.
The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five. L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique.
If trouble is experienced with this equipment, for repair or warranty information, please contact SmartRG,Inc. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
